Question about 1997 Nissan.5 Altima

Open Question

Replaced 1997 Nissan altima Crankshaft Position Sensor and still get troible code P0335

Posted by on

  • Jeff Turcotte
    Jeff Turcotte Oct 16, 2010

    check the connector for bent pins or bad terminals

  • zigmondjmoli Oct 19, 2010

    Thank you. I will give it a good looking over. Would you happen to know how to check the voltage to.. the crankshaft position sensor?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 94 Answers

SOURCE: need to change crankshaft position sensor for 2001 elantra

down by your crank shaft pulley you will find a sensor with 2 wires ruining into it and 1 bolt holding the sensor in remove the bolt and twist and pull on the sensor then slide the new sensor in then reinstall bolt and wire

Posted on Mar 08, 2009

Ad
  • 383 Answers

SOURCE: CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA

1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Posted on Apr 06, 2009

  • 383 Answers

SOURCE: CANNOT FIND THE CRANKSHAFT POSITION SENSOR

cerebral_eni: The crank position sensor is located at the back of the engine block just below the cylinder head. It actually projects into the bell housing and reads the teeth on the flywheel where it references TDC for #1 cyl and RPM's of the crank. It's a "Hall effects generator". Unless you are into electronics and have a lab scope to look for a square wave pattern, I will continue with my other input.
Nissan has a recall campaign on the crank angle sensors.
The campaign # is 07V527000:ECM update for stalling;
NHTSA07V527000 NOV 07,
The symptom was brief malfunction of sensor causing the engine to quit running which could potentially put the vehicle at risk for a collision. The sensors would ultimately fail. There was also a voluntary recall on the reprogramming of the ECM's due to stalling problems. TSB# NTB07-081, Campaign ID#R0712
I hope this information is of some assistance to you. You may be able you get your car repaired under warranty! Good Luck!

Posted on Apr 08, 2009

  • 8 Answers

SOURCE: P0335 CRANK POSITION SENSOR A CIRCUIT MALFUNTION

crank sensors are usually located in/near the distributor.

Posted on Jun 07, 2009

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced camshaft and crankshaft position sensors in my 2005 altima also the o2 seneor car still will not run. error code 335 What else could be the problem?


DTC P0335 - Crankshaft Position Sensor A Circuit Malfunction
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

A P0335 "check engine light" code could be caused by:
Damaged CKP sensor connector
Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
Sensor output open
Sensor output shorted to ground
Sensor output shorted to voltage
Failed crank sensor
Broken timing belt
Failed PCM

If you need additional details about test and solutions, just contact us in the Code Link.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using Fixya, and have a nice day.

Jose.

Oct 21, 2011 | 2005 Nissan Altima

2 Answers

Nissan altima p0335 and p0725 is this a recall


I had the same codes on my 2003 Nissan Altima 2.5 SL


I replaced Crankshaft and Camshaft Positioning sersors and never had this problem since. Check my youtube videos how I did it:

http://youtu.be/7FsLBcuREYE
http://youtu.be/325s0pFQZtg

Apr 07, 2011 | Nissan Altima Cars & Trucks

2 Answers

02' Nissan Altima, car jerking, turns off at light, but turns right back on. Engine light on, code from autozone P0335 crankshaft position sensor. P0725 Engine speed signal circuit. The start up, days it...


If it has a code for loosing the crankshaft position sensor signal, I would certainly start looking at that before venturing into the fuel system. Cam and Crank sensors are a common failure item for Nissans of that era. Nissan actually redesigned the sensor and i think they performed a recall on some vehicles. They are fairly inexpensive and easy to replace. I believe they run about $40 each. Because most people don't have access to a powerful scanner or a digital storage oscilloscope to verify the failure I recommend replacing the cam and crank sensors at the same time.

Sep 02, 2010 | 2002 Nissan Altima

1 Answer

Code p0335


P0335 is fault code for crankshaft position sensor

May 28, 2010 | 2005 Nissan Altima

1 Answer

Nissan Altima 2004 SES light and some times engine donot start


its going to be between the motor and tran on the back lower part it is going to be in between a small gap i chande it on my friends car and it work

Aug 24, 2009 | 2005 Nissan Altima

2 Answers

Crankshaft Position Sensor Error P0335 recurred after r&r


In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Jul 25, 2009 | 2003 Nissan Altima

1 Answer

Crankshaft sensor


Replace the air flow meter.

Jul 19, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...