Question about 2002 Dodge Intrepid

1 Answer

How do I remover and replace 2002 dodge intrepid left headlamp assembly. Thanks Roger C.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 59 Answers

On the upper radiator support above the headlamp there shoudl be 2 bolts with very small heads, (about 5.5 mm). Take these bolts out, they should be very long pins. once they are removed, headlamps can be removed out teh front.

Posted on Oct 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the headlight lens of 2002 dodge intrepid


If you are replacing the whole headlight assembly, it is really easy. There are two long screws/bolts. They have a star-patterned screw/bolt. Remove those two fastners and pull the headlight straight out enough to disconnect the headlamp bulb from the backside.

Sep 15, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

How do you replace head light bulbs in a 2003 dodge intrepid


On each headlamp, you need to remove the screws holding the headlamp the the car (2 screws per headlamp)
Then pull the lamp out and change the bulbs.
Dont touch the new bulbs with your hands, use the plastic bag they came in (but remove the bag after install!!!)

Feb 06, 2010 | 2003 Dodge Intrepid

1 Answer

I need a digram of how to replace the timing belt for 2002 dodge intrepid 3.5 single dual cam


Hello trimaineiman: My name is Roger and I will help you. A couple of things you should do is replace the water pump while you have the timing belt off. Should the pump fail later it will do severe engine damage to the engines valves. Next This engine is not a free wheeling engine. Should you put the belt on and the valve timing oi not correct. Severe engine damage will occur. By that I mean Valves in the head will be bent and/or piston damage will occur. Here is a picture of the marks. It is the best i could find. Good luck on your repairs. Should you need further help please just ask. Please rate the answer as this way I know it was helpful. Thank You for using Fix Ya. Roger7ab4161.jpg

Jan 23, 2010 | 2002 Dodge Intrepid

1 Answer

Headlamp cover removal. I have purchased the


its stuck on ,evan if clips are present you still cant get the lens off,new headlights from a motor factor are not normally expensive

Nov 05, 2009 | 1999 Dodge Intrepid

1 Answer

Headlight replacement - 2002 Trailblazer


  1. Open and support the hood.Remove the grille.
  2. Pull up on the retaining tabs (1) in order to remove the headlamp assembly from the headlamp panel.
  3. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
  4. Disconnect the headlamp electrical connector (2) from the headlamp assembly.
  5. Remove the side marker socket (4) from the headlamp assembly.
  6. Remove the park/turn socket (3) from the headlamp assembly.
  7. Remove the headlamp assembly from the headlamp panel.
  8. Installation:
  9. Position the headlamp assembly to the headlamp panel
  10. Index and seat the tabs on the park/turn socket (3) to the headlamp assembly.
  11. Index and seat the tabs on the side marker socket (4) to the headlamp assembly.
  12. Connect the headlamp electrical connector (2).
  13. Connect the headlamp leveling electrical connector to the motor/actuator if equipped.
  14. Align and install the 4 locator pins on the back of the headlamp assembly into the retaining tab holes.
  15. Push down on the retaining tabs (1) in order to lock the headlamp assembly into the headlamp panel.
  16. Install the grille. Refer to Grille Replacement .
  17. Close the hood

Oct 27, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

Never changed a bulb


Headlamps -- remove two long bolts with 7 mm or 8 mm hex heads for each headlamp assembly. These bolts are located in the horizontal body panel above and either side of the headlamp assembly. Headlamp can then be pulled forward far enough to remove the lamps from the assembly (twist about a quarter turn).

Taillamps -- inside the trunk, you may have to move the trunk liner aside, but there are three plastic wing nuts holding each taillight assembly in place. After removing these wing nuts, the assembly can be removed.

Sep 25, 2009 | 2002 Dodge Intrepid

1 Answer

How do you adjust head lights on a1996 dodge intrepid after replacing both light assembly. Car was hit in the front & had to replace both lights on the car, lights are used from junk yard.


You should have two plastic nuts on each headlamp assembly, one will be for your high beams and one will be for your low beams.

The nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail (might see holes in your rail above the headlamp unit where the screws are hidden)

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Sep 21, 2009 | 1996 Dodge Intrepid

1 Answer

How do i take out a cooling fan out of a intrepid


YOU MUST REMOVE UPPER RAD SUPPORT TO REMOVE COOLING FANS..REMOVE ALL 10MM,13MM HEADED BOLTS..REMOVE 4 HEADLAMP SCREWS..7MM HEAD..THERE ARE 2 PLASTIC RIVETS THAT MUST BE CUT OFF AS WELL..HOOD LATCH CAN STAY WITH SUPPORT,LAY BACK ON TOP OF ENGINE OR REMOVE IT..MARK LOCATION ON SUPPORT..REMOVE 4 BOLTS FROM FAN ASSEMBLY,UNPLUG IT..IT ALSO COMES OUT EASIER WITH UPPER RAD HOSE DISCONNECTED..1 CLIP ON TOP OF FAN HOUSING AS WELL

Aug 31, 2009 | 2001 Dodge Intrepid

1 Answer

Cut out when accelerating


The battery is located under the right headlamp assembly. To access it remove the right front tire and the access panel at the forward area of the fender well. As far as cutting out, that would depend on several things like when was the last tuneup, is the throttle body clean, any engine fault codes and that sort of stuff.

Aug 19, 2009 | 2002 Dodge Intrepid

Not finding what you are looking for?
2002 Dodge Intrepid Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...