Question about 1997 Chevrolet Lumina

Open Question

How do I replace brake switch on a 1997 chevy lumina

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: replace turn signal switch 1998 chevy lumina

You may look or feel the back side of the steering wheel, looking for 2 screws that hold the airbag to the wheel, these will be internal torq type screws (star) you may have to rotate the steering wheel 90 degrees to access the screws. You should first disable the airbag, by removing the airbag fuse, and or by disconnecting a yellow connector located near the base of the steering column. under the knee bolster.(panel below column). Once the retaining screws are removed, lift bag and disconnect the 2 connector to the airbag, the ground for the horn, and the horn contact wire, which requires you to push down and twist counter clockwise, damage to the horn contact ring will occur if you try and just pull connector from the ring. Now you can remove the steering wheel, may require a puller, and the you will have access to the turn signal switch.

Posted on Jul 20, 2009

  • 306 Answers

SOURCE: The brake lights wont work. The brake light over

the break light wire on the lumina runs through the blinker switch or multifunction switch on the colum.. check there as well as at the tail light sockets. on the late 90s gm cars the sockets had a tendancy to rot away... use a test light at the brake light wire in the trunk and have a friend apply the break. if there is power then may have to get new tail lights. or replacement bulbs.

Posted on Mar 13, 2010

Testimonial: "THANKS FOR THE HELP"

fastboyz
  • 674 Answers

SOURCE: Brake lights 1997 Chevy Lumina

i would check the bulbs first. then continue to the brake switch

Posted on Sep 10, 2008

emissionwiz
  • 75814 Answers

SOURCE: 2001 Chevy Lumina brake lights not working

test and replace the brake light switch, it is located at the top of the arm the brake pedal is attached to.

Posted on Mar 26, 2009

AUTODOC01
  • 216 Answers

SOURCE: brake wiring diagram chevy lumina

why not just replace the turn signal switch must faster and safer . buy one from your local parts house then you can see its not that easy to install but you can do it with a little help

Posted on Aug 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Chevy Lumina REAR BRAKE LIGHTS DONT WORK


This will either be a fuse or the brake light switch which is on the pedal it's self. More likely the switch as these are fickle at best.

Nov 22, 2011 | 1997 Chevrolet Lumina

1 Answer

I have changed my brake switch, fuses, and bulbs in my 1997 chevy lumina and the brake lights still will not work at all, my signal lights only work. What could be the problem?


here is howw it goes, the power from the fuse goes to the brake switch then to the signal light switch and from there to the rear lights, test for signal from the brake switch to the turn signal, if good the signal switch is bad

Apr 13, 2011 | 1997 Chevrolet Lumina

2 Answers

97 chevy lumina break lights


All you need is a new brake light switch which is mounted by the brake pedal

Apr 28, 2010 | 1997 Chevrolet Lumina

1 Answer

The brake lights wont work. The brake light over


the break light wire on the lumina runs through the blinker switch or multifunction switch on the colum.. check there as well as at the tail light sockets. on the late 90s gm cars the sockets had a tendancy to rot away... use a test light at the brake light wire in the trunk and have a friend apply the break. if there is power then may have to get new tail lights. or replacement bulbs.

Mar 13, 2010 | 1997 Chevrolet Lumina

2 Answers

Brake wiring diagram chevy lumina


why not just replace the turn signal switch must faster and safer . buy one from your local parts house then you can see its not that easy to install but you can do it with a little help

Aug 26, 2009 | 1997 Chevrolet Lumina

3 Answers

Brake lights don't work on 97 chevy lumina sedan


Had the same issue in the spring. Replace the turn signal switch. A general weakness in the switch in these years. Replacement solved the problem in my 97 Lumina.

May 07, 2009 | 1997 Chevrolet Lumina

1 Answer

2001 Chevy Lumina brake lights not working


test and replace the brake light switch, it is located at the top of the arm the brake pedal is attached to.

Mar 26, 2009 | 1997 Chevrolet Lumina

1 Answer

Brake Light Problem -1997 Chevy Lumina


The ground wire in the trunk area, coming from the brake light harness, might have come off or really loose. Hope this will get your lights working again. Best wishes.

Jan 20, 2009 | 1992 Chevrolet Lumina

2 Answers

Brake lights 1997 Chevy Lumina


i would check the bulbs first. then continue to the brake switch

Sep 10, 2008 | 1997 Chevrolet Lumina

Not finding what you are looking for?
1997 Chevrolet Lumina Logo

Related Topics:

450 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...