Question about 2000 Hyundai Elantra

2 Answers

Turn signals /hazard lights don't blink

Blinkers and hazard lights do not work. all the blubs are new and are working..what could be problem?

Posted by on

  • 1 more comment 
  • recon11e May 18, 2009

    Turn signal and hazard do not work, all other lights are funstioning. Have checked fuses and all are OK

  • Anonymous Mar 17, 2014

    the blinkers do not work I put a new switch in the car and it will pop the fuse number 30 as soon as you try to turn the signal on. I have thought about the hazard switch. could that be my problem?

  • Anonymous Mar 30, 2014

    2000 Nissan Frontier All lights blinking
    when I turn my key on all my lights start flashing they will stop flashing when I turn my head lights on but then my blinkers and hazards don't work any help please

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had the same problem and found the problem to be the turn signal flasher.local parts store sells for 9.99.The hardest part I found was finding someone who knew the location of the part on the car.after checking with a mechanic at the dealer. I finally found it with a flashlight. it is against the driver side firewall inside of the car as far up as you can see while laying on your back in the floorboard and looking up with a flashlight. as soon as this was replaced my hazard lights and turn signals worked perfectly. hope this helps someone else.

Posted on May 28, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

Hi! check first for any blown fuse. INSPECTION 1. Check for a burnt fusible link with an ohmmeter. 2. If a fusible link burns out, there is a short or some other problem in the circuit. Carefully determine the cause and correct it before replacing the fusible link. The fusible link will burn out within 15 seconds if a higher than specified current flows through the circuit.turn signals /hazard lights don't blink - 2f5ff5a.gif

Posted on Jun 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 celica and for some reason the front signals does not work at all. When I turn on the blinkers it blink really fast on both sides but hazard light works fine it blinks normal but it...


check the main earth wire near the battery. and one near the rear of the lights. unbolt them and clean the connectors up put some grease on them after. then check again. remember that when the earth wires come off the radio code will be needed to reset the the radio. be safe and take the battery off.

Sep 28, 2013 | Cars & Trucks

1 Answer

Turn signal hazard lights work but not running lights


The parking lights should be on a different circuit from turn signals - hazard lights. The bulbs usually have two filaments, one for each circuit.
On most models there is a tail light fuse and relay that handles front and rear parking lights.

Jun 28, 2013 | Toyota Tacoma Cars & Trucks

1 Answer

Blinkers only work sometimes


chevy had an issue with the blinkers and hazards not working all the time i found that when my turn signals stop working push the hazard switch until they blink then the turn signals start working again. its a faulty turn signal/hazard switch that needs to be replace costs about 30 bucks pretty simple to replace.

Dec 24, 2010 | 2000 Chevrolet Malibu

2 Answers

Turn signal doesn't come on until I hit my hazard light on & off


it could be duel filament bulb that is blown and shorting inside the bulb to the other circuit, you may need to remove all indicator and hazard bulbs and check. I would also try a new flasher can

Apr 17, 2010 | 2003 Chevrolet Impala

1 Answer

TURN SIGNAL, BRAKE & HAZARD LIGHTS


No Turn Signal Operation (blinker)The turn signal lights in your car are a basic electrical system that controls the front and rear blinker lights to alert the intended direction of the vehicle. We have listed some of the most common problems and repair troubleshooting tips below:
Troubleshooting Procedure
To start troubleshooting this problem:
  • Turn the key to the on position (do not start engine)
  • Inspect the system fuse located in the fuse panel and replace if needed. If you cannot find the location of the blinker fuse consult your owner's manual or an online repair manual
  • When a blinker flasher fails it can cause blinker lights to say on, not blink, or not go on at all. To test the blinker system flasher, remove the flasher unit and insert a jumper wire between the two terminals. If blinker stays on in both directions without blinking, replace the flasher. If you cannot find the location of the blinker flasher consult your owners manual or an online repair manual.
  • 1b7f814.jpg

Jul 09, 2009 | 1999 GMC Denali

1 Answer

Right rear blinker not working!


check the socket whare the bulb goes for rust corosion. you can also test the socket by removing bulb and using a 12 volt test light. remove bulb and connect test light leads to the socket while the signal is on.connect one lead from test light to inner wall of socket and the other one to the terminals in bottom of socket

Jan 13, 2009 | 1995 Ford F250

1 Answer

No turn signals or emergency blinkers


I had the same problem twice before. Solved it the same way both times. In my case it was the Hazard switch at the top of the steering column. It was stuck. I knew it was that because the signal lights had been functioning perfectly until I parked my car alongside the road with the hazard lights on to do some nighttime fishing and sip a little white lightnin'. (just kiddin' about the white lightnin')

When I got back in my car to go, I turned off the hazard lights but I had no turn signal lights! So I kept pushing that hazard button up and down for about 30 times with my left turn signal arm down until it started working again. So after having this happen to me twice, I learned a valuable lesson: Don't ever use hazard signals in this car.

Dec 12, 2008 | 1998 Lincoln Town Car

1 Answer

99 VW Jetta


The turn signal relay is inside the hazard switch on the dash. Get a new one (about $30) and install that and you're cured:)

Sep 02, 2008 | 1999 Volkswagen Jetta

Not finding what you are looking for?
2000 Hyundai Elantra Logo

1,256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...