Question about 2002 Chevrolet Camaro

1 Answer

My driver side electric window assembly collapsed and the window fell down inside the door. The motor is still very good, but I need info and/or a diagram of how it is assembled in order to repair it and get the needed parts. Can you help me with this problem?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 277 Answers

My driver side electric window assembly collapsed - f82a631.gif

  1. Lower the window halfway.
  2. Remove the front side door trim panel.
  3. Remove the water deflector.
  4. Support the window in a position needed to access the window rivets by inserting a rubber wedge door stops (1) at the front and rear of the window between the window and the door inner panel.
  5. Drill out the window rivets (3) with a 1/4 inch drill bit.
  6. Remove the window (1) by lifting out of the door. Important: Inspect the window bushings, window bushing retainers, window front up stop, window stabilizer pins and window wedges on the window for damage.
  7. Remove the window bushings and window bushing retainers if necessary, using a flat-bladed tool covered with cloth body tape.
  8. Remove the window front up-stop screw if necessary.
  9. Remove the window front up-stop, front up-stop nut and front up-stop washer if necessary.
  10. Remove the window stabilizer screws, if necessary.
  11. Remove the window stabilizer pins, stabilizer pin nuts and window wedges if necessary.
Installation

  1. Install the window stabilizer pins, stabilizer pin nuts and window wedges if necessary. Notice: Refer to Fastener Notice in Service Precautions.
  2. Install window stabilizer screws, if necessary. Tighten the window stabilizer screws to 7 N.m (62 lb in).
  3. Install the window stabilizer pin nuts, if removed. Tighten the window stabilizer pin nuts to 8 N.m (71 lb in).
  4. Install the window front up-stop washer, if removed.
  5. Install the window front up-stop screw, if removed. Tighten the window front up-stop screw to 7 N.m (62 lb in).
  6. Install the window front up-stop nut if removed. Tighten the window front up-stop nut to 8 N.m (71 lb in).
  7. Install the window bushings and bushing retainers, if removed.
  8. Install the window (1) into door so that holes in window bushings line up with holes in channel.
  9. Install the window rivets (3) in sequence.
  10. Install the water deflector.
Hope this helps

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The drivers side window fell into the door of 96 rendezvous. How do i put it back on track?


The door trim is held on with a combination of screws and push clips Once you have the trim off you will probably find that the window motor regulator is defective. I would recommend replacing the regulator and motor as an assembly.

Are you sure of the year? Didn't think that they made a 1996 Buck rendezvous

.http://www.dormanproducts.com/gsearch.aspx?

Feb 23, 2015 | Cars & Trucks

1 Answer

How to remove left side window motor??


first remove the door panel to give access to the window and regulator assembly you can move the window up or down in order to access the 2 screws or bolts holding the window to the regulatorr assembly if not possible put your hand up inside and try to loosen the screws or bolts with a wrench or small screw driver then the window should fall becareful not to break or damage the glass then unbolt the regulator from door frame and pull it out through the hole if electric the motor should come with it if just manual the rods and so on come with it if electric you need to unplug the motor connector

Aug 06, 2014 | 1992 Ford Explorer

1 Answer

My driver side window wont roll up


First check the fuses for both electric windows if they are good.The fuse box one is on the engine compartment driver side look for long retangular black box and open the fuse cover the cover should designate what the fuses and relay is for the other is on the driver side under the dashboard just above your left foot look under you should see another fuse box.If both fuses are good,then your going to have to check the window regulator which is inside each door.Open the door panel and check window regulator morethan likely the regulator assembly need to be change.You might just need the motor.The whole assembly is quite expensive.

Nov 06, 2012 | 1996 Lexus ES 300

1 Answer

Drivers side window switch clicking


Larry if the window does not go up or down its likely that the gear driven assembly or the motor on your electric window for the drivers door is bad. You will need to disassemble the door by removing the door panel to gain access to the electric motor. Hope this helps you will want to gain access to a service manual from a local parts store to help you with this venture. Good Luck

Nov 28, 2011 | 2002 Kia Sedona

1 Answer

Drivers electric window suddenly fell down inside of door


thw window either came off the window slider or the slider bracket, this can be determined by removing the door panel. this could also be cable driven and the cable has disconnected or broke, can also be determined by removing door panel.

Oct 01, 2009 | 2001 Volkswagen Golf

1 Answer

Drivers window fell down 2003 Impala


Most all window motors and regulators are pop-riveted to the door. This requires special tools to reinstall the pop rivets and assembly.

Jul 18, 2009 | 2003 Chevrolet Impala

2 Answers

Window glass wont move


Most likely the sound is coming from your "window lift assembly" being torn up. Your window motor attaches to the back of the assembly and winds up the cable that raises and lowers your window. Most likely the cable has come unattached and is grinding inside. 
You can buy a new assembly from Autozone (about $100 is what they usually run) and replace it. The first step is to remove the side panel from your door. Once the panel is off you can see where your motor is bolted on to the center of your door. Remove the motor and then unbolt the rest of the window lift assembly. Be careful though about removing the pins that attach your window to the lift assembly. Due to the curve of the glass, it only takes a little pressure to shatter the glass. Once the window lift assembly is replaced, put everything back the way it was before and you are good to go. 
It is not that complicated of a job, it just takes a little patience. Good luck!

Jun 25, 2009 | 1999 Volkswagen Passat

1 Answer

Driver side window is off track and stuck about 75% closed


If your power window motor is not moving up or down at all inside the door panel, you will need a new motor.
If your window is stuck and will not move, it is the motor - it is bad.
If your window falls down into the door panel, the window is off track.
Replacing a window motor is an easy fix, get another one from an auto parts store and replace it.
Good luck!

Mar 12, 2009 | 1993 Honda Accord

Not finding what you are looking for?
2002 Chevrolet Camaro Logo

544 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...