Question about 2005 Mercury Sable

1 Answer

Motor resistor needs replacement need to locate it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,565 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My heater blowers dnt work and i need to knw where i can locate the resister blocks for my heater blowers so i can ghange them


Its located under dash,or near glove box.

The dash panel lower side has to be out.

HEATER BLOWER MOTOR


Its faulty blower motor resistor. The low and medium speed on blower motor is controlled by resistor and its actual speed is high. So because resistor is not working, blower motors actual speed which is high is working.


It can be faulty blower motor or faulty blower motor resistor. Get the blower motor inspected. If it's faulty it has to be replaced.


=======

For blower motor testing and replacing, check the link below: ----

Blower motor Testing/replacing for all vehicles?

http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.html

------------

These will help.

Thanks.

Nov 28, 2012 | Cars & Trucks

2 Answers

98 century heater blower motor resistor location


look under the passenger side of the dash. There will be a plastic trim panel that will need to be removed. Once its out of the way you will see the blower motor. The resistor will be just to the drivers side of the blower motor.

Nov 15, 2011 | 1998 Buick Century

1 Answer

Where is the heater blower resistor located in a 2000 Subaru Outback? I've seen one reply in a forum saying it is to the left of the blower motor, but I don't know where that is either. I need to...


the blower motor is located under the passenger side of the dash. The blower motor resistor is located behind the glove box assembly. You will need to remove the glove box assembly and then you will see the resistor. It will have one connector with four or five wires and will be held to the HVAC unit with 2 screws.

Jun 23, 2011 | 2000 Subaru Outback

2 Answers

I have a 1998 ford f 150 and the blower motor only works on high


This problem is caused by a defective blower motor speed control resistor.

BLOWER MOTOR LOCATION
The blower motor resistor is located under the glove box. You can locate it by finding a 4 wire connector, directly below the glove box hinge (towards the front of the truck). There are 2 screws holding it in. A mirror is helpful in replacing this, but I managed to replace it without one. You will need a nut driver to remove the screws. My suggestion is to leave the wires connected to the resistor while removing the screws.

Nov 10, 2010 | 1998 Ford F150 Regular Cab

2 Answers

Where is the hvac blower motor located? If you replace the blower motor do you need to replace the resistor too?


Dear Blower Motor Searcher,
The blower motor is located under the dash on the pass side in front.Open the pass front door , get on your knees, and look up under the dash, you will see the flying saucer looking object, that is the blower motor.Right next to it is where the resistor is located, and yes it is recomended that you replace the resistor also because that is where the main current flows thru to get to the blower motor.That actually controls the current of the motor, which controls the speed of the motor, low, med, high, recirc, etc....any other questions get back to me, TX!! HOPE I COULD HELP!!!

Nov 20, 2009 | 2003 Pontiac Aztek

1 Answer

Fan only works on high


It isn't the switch it needs a new blower resistor and new fan motor.
The fan motor will start to pull too many amps through the resistor and in turn smokes the resistor. You can replace the resistor and it will temporarily fix the problem but eventually the fan motor will end up overloading the new resistor and ruining it.
Replace both the resistor and the blower motor. The resistor is located on the firewall inside of vehicle on the passenger side. If I remember correctly it is a bit of a ****** to get to the screws.
Also if you have automatic temperature control the GM part number for the resistor should be 89018643

Nov 09, 2009 | 1999 Buick Century

5 Answers

Blower motor only works on one speed


If it only works on high, replace blower motor resistor.

Jun 19, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Blower motor resistors bank needs to be replaced Jeep Liberty2005


the resistor for the blower motor is located behind the glove box easy to get to and replace

Jun 17, 2009 | 2005 Jeep Liberty

1 Answer

Have to change blower motor resistor where is it located


Located behind glovebox. 2 screws and 2 plugs. very simple

May 11, 2009 | Chrysler Town and Country Cars & Trucks

Not finding what you are looking for?
2005 Mercury Sable Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

fordexpert

Level 3 Expert

5481 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...