Question about 1993 Toyota Camry V6

1 Answer

If the mark on the crankshaft timing pulley is aligned with the mark on the engine block, does this mean that the Number 1 cylinder is at TDC?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 84 Answers

It means that when alligning the cylinders and after making sure the number one cylinder is at top dead center and the cam marks should be at the very top aligned with one another.

If I can help more please feel free to ask!

Joe

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cam timing for fiat siena 1.2 2001


There are no timing marks on this engine - the engine has to be "locked" using special engine locking / setting kit which you wil have to obtain to do the job.

I will give you the instructions to do the job for when you have the locking kit to do the job.. as follows:

Removal
  1. Raise and support front of vehicle.
  2. Remove:
      • RH front wheel.
      • RH inner wing panel.
      • Air filter assembly.
  3. Support engine.
  4. Remove:
      • RH engine mounting and bracket.
      • Timing belt upper cover,
      • AC receiver/drier (if fitted). DO NOT disconnect hoses.
      • Timing belt lower cover.
      • Auxiliary drive belt.
      • Support bracket between gearbox and cylinder block (Palio).
  5. Palio: Remove bell housing cover plate. Fit flywheel locking tool. Tool No.1.867.029.000. or equivalent commercially available.
  6. Remove:
      • Crankshaft pulley bolts
      • Crankshaft pulley
      • Spark plug leads.
      • Ignition coil and bracket.
      • Spark plugs.
  7. Fit dial gauge and adapter to No.1 cylinder. Tool No.1.860.895.000.
  8. Turn crankshaft to TDC on No.1 cylinder. Set dial gauge to zero.
  9. Ensure notch in rear of camshaft aligned as shown.
  10. Install camshaft aligning tool. Tool No.1.870.823.000

  11. NOTE: If camshaft aligning tool cannot be fitted: Turn crankshaft one turn clockwise.

Installation
  1. Ensure No.1 cylinder at TDC by turning crankshaft slightly clockwise and anti-clockwise. Use dial gauge .
  2. Ensure camshaft aligning tool fitted correctly
  3. Hold camshaft sprocket. Use tool No.1.860.831.000/001
  4. Slacken camshaft sprocket bolt
  5. Fit timing belt in following order:
      • Crankshaft sprocket.
      • Water pump sprocket.
      • Camshaft sprocket.
      • Tensioner pulley.
    NOTE: Observe direction of rotation marks on belt.
  6. Fit tensioning tool locating pegs to tensioner pulley holes -Tool No.1.860.745.100/300. Ensure tensioning tool arm is horizontal.
  7. Set weight at 70 mm mark on scale bar.
  8. Hold camshaft sprocket
  9. Tighten camshaft sprocket bolt - Tightening torque: 70 Nm.
  10. Remove aligning tool
  11. Turn crankshaft two turns clockwise.
  12. Ensure No.1 cylinder at TDC by turning crankshaft slightly clockwise and anti-clockwise. Use dial gauge
  13. Ensure camshaft aligning tool can be fitted - If not: Repeat installation procedure.
  14. Tighten tensioner nut to 28 Nm
  15. Remove:
      • Tensioning tool
      • Camshaft aligning tool
      • Dial gauge
  16. Install components in reverse order of removal.
  17. Tighten crankshaft pulley bolts - Tightening torque: 20 Nm + 90°.

Jun 26, 2016 | Fiat Cars & Trucks

1 Answer

How do you find TDC on conpression stroke 1998 dodge dakota 3.9 v6


Turn crankshaft pulley until TDC mark aligns with engine block pointer. Remove rocker cover and check that cylinder 1's valves are closed (not compressed). This is cylinder 1 TDC firing position.

Nov 01, 2012 | Cars & Trucks

1 Answer

I need timing marks on 2.2 toyota camry 2000


1. Remove the fan and generator V belt:
tdisline_542.jpg

tdisline_543.jpg 2. TIMING CHAIN (2az-FE Engine):
Before servicing the vehicle, refer to the Precautions Section.
Drain the engine oil.
Remove or disconnect the following:
Negative battery cable
Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:
1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.

2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley
tdisline_544.jpg Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine
tdisline_545.jpg

Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine

Remove or disconnect the following:
Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner

  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:
    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
    tdisline_546.jpg
  • Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine
    tdisline_551.jpg

    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.

    Remove the bolt, chain tensioner and spring.

    Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top

    tdisline_552.jpg

  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine
    Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.

  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
  • tdisline_553.jpg Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine
    tdisline_554.jpg Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine
    tdisline_555.jpg Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine
    tdisline_556.jpg Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine
    tdisline_557.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    May 21, 2011 | Toyota Camry Cars & Trucks

    1 Answer

    1977 ford pinto timming marks


    Hope this helps. Please don't forget to rate....thanks!



    c17hydro_169.gif

    Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)


    On 2000 cc engines, turn the crankshaft until the two round locating holes in the camshaft pulley are visible from the rear side of the pulley, looking forward from the left-side of the car. When these two holes are parallel to the ground, the timing pointer on the crankshaft pulley should point to TDC. If the drive belt is dislocated, the crankshaft damper will be retarded or advanced 19° per cog on the belt.

    If the engine you are working on does not have the two locating holes on the rear side of the camshaft pulley, then you will have to remove the drive belt cover and observe that when the crankshaft timing marks are aligned to TDC of the compression stroke of the No. 1 cylinder, the distributor rotor is pointing to the index mark on the upper lip of the distributor housing which coincides with No. 1 spark plug tower, and the pointer on the camshaft pulley is aligned with the index mark on the cylinder head.

    On 2300 cc engines, there is an access plug provided in the cam drive belt cover so that the camshaft timing can be checked without removing the drive belt cover. Remove the access plug, turn the crankshaft until the timing mark on the crankshaft damper indicates TDC, and observe that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover. Also, the rotor of the distributor must align with the No. 1 cylinder firing position.


    CAUTION:

    After any procedure requiring removal of the rocker arms on the 2300, each lash adjuster must be fully collapsed after assembly, then released. This must be done before the camshaft is turned.



    Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)

    Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)
    c17hydro_170.gif

    Checking 2000 cc overhead camshaft timing (© Ford Motor Co)

    May 08, 2011 | Ford Mustang Cars & Trucks

    1 Answer

    Como poner la banda de tienpo de un toyota camery


    Installation
    1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

    CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
    4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
    CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
    9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

    Dec 23, 2010 | 1993 Toyota Camry V6

    2 Answers

    Timing belt


    TIMING BELT & SPROCKETS R & I
    NOTE: Some procedures may differ slightly due to engine
    construction.
    Removal
    1) Remove all necessary air ducts. Position No. 4 piston at
    TDC of compression stroke. Align timing marks. See Fig. 2. Remove fan
    and fan shroud. Remove belts. If necessary, remove radiator and
    splashguard.
    2) Prevent engine from rotating and remove crankshaft timing
    pulley retaining bolt. Remove upper and lower timing belt covers.
    Remove spring from tension pulley. Loosen adjusting bolt and move
    pulley toward water pump. Remove timing belt.
    CAUTION: Ensure pistons are at TDC when rotating camshaft or damage
    may result.
    Inspection
    1) Handle timing belt carefully. Avoid twisting or kinking
    belt. Do not allow belt to become contaminated by water, oil, dirt or
    other contaminates. Inspect belt for cracks or damage. If necessary,
    replace.
    2) Measure tension pulley spring length and force. Spring
    length should not exceed 2.76" (70.2 mm) and spring force should not
    be less than 197-347 lbs. (27-48 kg).
    3) Replace tension pulley spring if not within specification.
    Installation
    1) Pull tensioner fully toward water pump side and
    temporarily tighten retaining bolt. Ensure No. 4 cylinder is at TDC on
    compression stroke by rotating crankshaft until keyway aligns with
    mark on front crankshaft seal housing (12 o'clock). Rotate camshaft
    until timing mark on cam gear (arrow) aligns with mark on upper
    camshaft cover (notch). See Fig. 2.
    NOTE: When timing marks are aligned as stated above, No. 4 piston
    is at TDC on compression stroke.
    2) Position timing belt over crankshaft sprocket, oil pump
    sprocket, camshaft sprocket and tensioner in that order. Ensure belt
    is positioned in sequence given and without slack between sprockets.
    Loosen tension sprocket adjusting bolt allowing spring tension to
    tighten belt. Tighten adjusting bolt temporarily.
    3) Temporarily install crankshaft pulley bolt and rotate
    crankshaft 2 complete revolutions in opposite direction of engine
    rotation, until marks on crankshaft and front oil seal retainer are
    aligned again. See Fig. 2. Loosen tensioner lock bolt, allowing
    tesioner spring to fully adjust tension. Tighten tensioner lock bolt.
    4) Install timing belt covers. To complete installation,
    reverse removal procedures. Tighten all bolts to specification. See
    TORQUE SPECIFICATIONS table at end of this article.
    Fig. 2: 2.3L & 2.6L Timing Alignment Marks
    Courtesy of Isuzu Motor Co

    Dec 13, 2010 | 1989 Isuzu Pickup 2WD

    1 Answer

    Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


    To Install:
    NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
    honda-03-23-3425.gif

    1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

    2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

    3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
    4. Loosen and ten retighten adjusting nut.
    5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
    6. Install lower cover.
    7. Install crankshaft pulley and bolt.
    8. Rotate crankshaft pulley counterclockwise several times to seat belt.
    9. Loosen adjusting nut 1 turn.
    10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
    11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

    12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

    13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
    14. Remove crankshaft pulley and lower cover.
    15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
    16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
    17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

    18. Remove bolt and washer from maintenance hole.
    19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
    20. Insert bolt into maintenance hole and hole in balancer shaft.
    21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

    22. Align groove on balancer shaft with pointer on oil pump housing.
    23. Install balancer belt and loosen adjusting nut 1 turn to tension.
    24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

    25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
    26. Reinstall crankshaft pulley.
    27. Loosen adjusting nut 1 turn.
    28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
    29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
    30. Remove crankshaft pulley.
    31. Install lower cover.
    32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
    33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

      CAUTION
      Do not use impact wrench to perform following step.
    34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
    35. Install dipstick/tube assembly.
    36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
    37. Install cylinder head cover.
    38. Install alternator bracket and alternator.
    39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

    40. Install upper bracket and tighten fasteners in proper numbered sequence.
    41. Install stop.
    42. Install battery and enter radio anti-theft code.
    prev.gif next.gif

    Jul 03, 2010 | Cars & Trucks

    2 Answers

    Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


    Hi,


    You find the timing marks on the picture below.

    moz-screenshot-2.pngaab8238.jpg



    Removal
    Remove auxiliary 1. drive belts.
    2. Support engine.
    Remove:
    Engine mounting and bracket.
    Timing belt upper cover [1].
    3.
    4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
    Remove:
    Crankshaft pulley bolt [4].
    Crankshaft pulley [5]. Use tool No.09213-60017.
    5.
    6. Ensure timing marks aligned [2] & [3].
    7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
    Remove:
    Timing belt lower cover [7].
    Crankshaft sprocket guide washer [9].
    Timing belt.
    Tensioner pulley.

    Installation
    Installation
    1. Check tensioner pulley for smooth operation.
    2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
    3. Fit tensioner and spring. Ensure spring is connected correctly.
    4. tighten bolt [6].
    5. Ensure timing marks aligned [2] & [3].
    6. Fit timing belt. Ensure belt is taut between sprockets.
    Install:
    Crankshaft sprocket guide washer [9].
    Timing belt lower cover [7].
    Crankshaft pulley [5].
    7.
    8. Slacken tensioner bolt 1/2 turn [6].
    9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
    Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
    timing belt lower cover [7].
    10.
    11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
    12. Install components in reverse order of removal.
    13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
    Manufacturer: Toyota

    Jun 25, 2010 | 1997 Toyota Camry

    2 Answers

    I am planning to replace the timing belt on my daughter's 95 Corolla and was wondering what I need to align where before removing the belt eg How do I find TDC? Camshaft pulley and Crankshaft pulley...


    TDC is top dead center/ remove spark plug on cylinder no. 1/ rotate the crankshaft pulley using a socket wrench and power handle and check if the piston on your cylinder no. 1 reach the top center that is TDC/ remove timing belt cover and locate a synchronized marking on your camshaft and crankshaft pulley/ remove old timing belt/ install a new one but make sure that the mark on your camshaft and crankshaft is perfectly synchronized before putting the cover/ manually rotate the crankshaft pulley again and see if it rotates 360 deg. freely then you can be sure you did the job correctly.

    Apr 06, 2010 | 1995 Toyota Corolla

    2 Answers

    Need instructions to replace 1993 Toyota Camry Timing Belt


    Hi Kmcarroll77

    TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

    Installation
    1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

    CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
    4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
    CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
    9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
    b7619be.jpg
    92cabaf.jpg
    Hope this helps, don't forget to rate.

    Lazaruselite

    Feb 25, 2009 | 1993 Toyota Camry V6

    Not finding what you are looking for?
    1993 Toyota Camry V6 Logo

    Related Topics:

    77 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8518 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...