Question about 2000 Oldsmobile Alero

1 Answer

Window on drivers side froze and fell down and won't roll back up. How to take door panel off to fix the window

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 277 Answers

  1. Disconnect the negative battery cable. Important: When removing a door trim panel or switch plate, disconnect the negative battery terminal. This will eliminate the possibility of shorting out the switch if you use a screwdriver, an awl, or other metal object in order to remove the switch from the harness.
  2. Remove the window regulator handle, if equipped.
  3. Remove the front door warning reflector.
  4. Remove the door panel screw (1) through the hole in the door warning reflector opening.
  5. Use a flat bladed tool in order to remove the rear deck release switch bezel.
  6. Disconnect the rear deck release switch.
  7. Use a flat-bladed tool in order to remove the lower switch bezel trim screw access cover.
  8. Remove the lower switch bezel trim screws.
  9. Remove the lower switch bezel
  10. Use a flat-bladed tool in order to pry the front door switch bezel upward.
  11. Disconnect:
  1. Gently disengage the front door trim retaining clips and remove the door trim panel from the door.
Installation Procedure




  1. Install the front door trim panel to the door. Ensure that the retainers are locked into place.
  2. Connect the rear deck release connector.
  3. Install the rear deck release switch bezel. Press the bezel firmly into place.
  4. Install the window regulator handle to the door.
  5. Connect:
  1. Install the front door switch bezel assembly to the front door trim panel.
  2. Install the lower switch bezel trim panel. Notice: Refer to Fastener Notice in Service Precautions.
  3. Install the lower switch bezel trim screws.
  4. Install the lower switch bezel trim screw access cover.
  5. Install the door trim panel screw (1) through the hole in the front door warning reflector.
  6. Install the front door warning reflector.
  7. Connect the negative battery cable.

Posted on Oct 15, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 72 Answers

SOURCE: window came off track and fell into door need to

All you need to do first is remove the screws that hold the door handle on there should be three, next gently pop the panlr off useing a screw driver do not break the wires that control the windows and door locking system and then if you need to replace the entire window track do so but if you do not need to do not if you do it is easy to do so just remove the nuts at the botom of your door , they hold the window track in place and then remove the three bolts that hold the motor in place and then next gently pull the window up and then remove the traco after you have removed the window and reverse the process when putting new track in.

Posted on Sep 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver door won't lock or open with key and window rolls down by itself


you will need to remove the door panel and check out the back of the key lock ,something is broke here thats for sure

Jun 15, 2012 | 2001 Toyota Highlander

1 Answer

Outside handle on 1997 Toyota Avalon will not open door


Since you can get the door open, half the battle is already won. Yes, open the door, pull the interior door panel and take a look around. Watch inside with a flashlight (towards the rear of the door) as you roll the window down to see if you can see what it's snagged on.

Jun 03, 2010 | 1997 Toyota Avalon

1 Answer

2005 volvo s60 inside door latch broke


That is not true.
The handle fell off on the inside. You can remove all the screws, remove window and lock controls. Then take a large flat-tipped screwdriver gently pry off door panel. Pull up and off when loose. You will now have access to inside off door and put the rod back in the handle hole. If the plastic holder piece is broke you will need another one. Cheap.


Oct 01, 2009 | 2002 Volvo V70

1 Answer

Non working driver side power window 2003 Nissan Sentra


I had a similar problem, window fell down one day while driving. Screw was loose at bottom of window that connects to track. Was hard but fixed it and worked great after. Hope it helps u out.

Aug 08, 2009 | 2003 Nissan Sentra

1 Answer

My driver's side window will now roll up how do I fix it?


you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. Then pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything.Sounds like the linkages, or the gears of the regulator are done

Mar 25, 2009 | 1996 Chevrolet Beretta

1 Answer

Subaru impreza/ manual side window stuck


You are having a problem with the "window regulator" remove the door panel, see if the window regulator bolts fell out. they are usually in between the plastic door covering and the door or inside the door on the bottom. they are four bolts that a 10 mm wrench fit, they are short about 1/4 of an inch long, if they fell out you can simply put them back in (I recommend using lock tite on them) These bolts are located in the middle of the door a little towards the front. If your bolts are still in place you probably need a window regulator.

Mar 22, 2009 | 1996 Subaru Impreza

1 Answer

2001 Saab 95 se driver/passenger windows.


A car I owned the left rear window did that. I could pull it up by taking a hold of it while another person held the switch. They told me the problem was the track was made out of plastic and it had broken. They had to replace the track. Yes it was expensive to repair but is ok now.

Mar 10, 2017 | 2000 Saab 9-3 Viggen

Not finding what you are looking for?
2000 Oldsmobile Alero Logo

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...