Question about 1997 Lincoln Town Car

1 Answer


Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 232 Answers

Door hing pins?

Posted on Oct 15, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I need to remove a door hinge on a 1996 Lincoln town car

If you push the pins out, you can separate the two "halves" of the hinge to get access to the bolts. There are several answers to the question of how to remove the pins. Good luck!

Feb 14, 2015 | 1996 Lincoln Town Car

1 Answer

Passenger door

If this is an older csr chances are the hinge pin bushins are worn, you can check this by trying to lift the door at the rear of it. You can obtain new pins at yoyr loc as l parts store.

Nov 09, 2013 | 1997 Lincoln Town Car

1 Answer

How to align passenger door

After several years the hinge pins an bushings become worn. You can obtain these from a local parts store in the (help parts) section.

Nov 09, 2013 | 1997 Lincoln Town Car

1 Answer


Hmmm... If like other cars, you would normally adjust the striker post on the B-pillar.
Unless the hinge pins are worn, in which case the door would drop, and need lifting as you closed it, to allow the lock to align. The pins are usually replacable.

Nov 09, 2013 | 1997 Lincoln Town Car

1 Answer

The drivers door hinge pins are loose allow the

Some local auto parts have replacement door/hinge pin-kits for Ford products. (If not order from your local Ford dealer) The pins may need heated with a torch and driven out with a long spline pin punch. You might want to get a mechanic to do this for you.

Mar 15, 2010 | 1997 Lincoln Town Car

1 Answer

How to remove the passenger door and replace it with another door on a 1994 lincoln town car.

Removal & Installation
NOTE Two people are needed to remove and install the doors.

  1. Disconnect the negative battery cable.
  2. Detach the necessary wiring connectors.
  3. Matchmark the door hinges to the body. This will aid in alignment when installing the door.
  4. With an assistant supporting the door, remove the hinge retaining bolts and remove the door.

NOTE If you are using a jack or similar tool to support the door, be careful not to damage the paint.

  1. If the door is to be replaced, transfer the following components to the new door if in usable condition: trim panel, watershield, outside moldings, clips, window regulators and door latch components.
To install:
  1. With an assistant positioning the door, install and partially tighten the hinge bolts.
  2. Align the door and tighten the bolts to 19–25 ft. lbs. (25–35 Nm).
  3. Attach the necessary wiring connectors and connect the negative battery cable.

Feb 10, 2010 | 1994 Lincoln Town Car

3 Answers

How do you change the door hinge pin? On 1997 lincoln town car?

Well cracklin joe half the hinge us welded to the door..Duh!

Jan 08, 2010 | 1997 Lincoln Town Car

2 Answers

1996 lincoln door hinge adjust

Which door is it ? If it is a front door, then it may be the hinge pin bushing that needs replacing. These can be bought at any auto parts store. Get the pin and bushing set because the hinge pin will need to be ground off to remove it. Press the new bushings in with pliers and insert the new pin from the top

Sep 10, 2009 | 1996 Lincoln Town Car

2 Answers


The inertia switch should be located in the trunk, on the right-hand side, behind the feltlike trim material.

Jul 09, 2009 | 1996 Lincoln Town Car

1 Answer

I need the door lock code location for my 2004 Town Car

The code should be on a white sticker located on the truck hinge. Mine is on the right hinge.

Jun 23, 2009 | 2004 Lincoln Town Car

Not finding what you are looking for?
1997 Lincoln Town Car Logo

Related Topics:

629 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

76846 Answers


Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides