Question about Jeep Grand Cherokee

Open Question

2000 Jeep Grand Cherokee owners manual - Grand Cherokee Jeep Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: heated seat 1996 jeep grand cherokee

C1 & C2 in your panel are most likely one of the culprits, if no power at heater at seat. Sounds like testing for power at seat switch is easier to do than get at these circuit breakers in the panel. If you have power at switch at seat, then it's not the fuse/circuit breaker. Good reading at this link for you.


http://www.wjjeeps.com/seats/seats.htm#HEATED

Posted on Dec 29, 2008

motor1258
  • 6674 Answers

SOURCE: Replacing water pump on 2000 Jeep Grand Cherokee V6

Here you go.Clicking on any of the pictures will expand them.
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004319c

Posted on Jan 10, 2009

whispers76
  • 55 Answers

SOURCE: Changing the water pump on 2000 Jeep Grand Cherokee V6

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

  • 2 Answers

SOURCE: How to replace headlights on 2000 Jeep Grand Cherokee

One long bolt at the top - requires a 7mm socket to remove the bolt. The light housing will pry out with a screw driver. There are three ball and socket type connectors that hold the housing in and I just pryed off the plastic housing carefully and "balls" pop out of the sockets. Finally, I was replacing the faded plastic housing and it came with a new wiring harness. It's impossible to reach the connector to use the new wiring harness that comes with the new plastic light housing. So just use the existing wiring harness with the new light assembly.

Posted on Feb 06, 2009

  • 6982 Answers

SOURCE: 2000 jeep grand cherokee 4.0 liter engine timing belt replacement

If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Posted on Apr 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Just purchased Jeep Grand Cherokee LTD TD 2001, looking for the handbook please?


Jeep Grand Cherokee 1999 at 2004 are called as WJ series.

Click in this link to download free 2004 Jeep Grand Cherokee WJ Owner's Manual.pdf (344 pages pdf file, 6.1 MB).

Hope helps (remember to rate this answer).

Apr 03, 2011 | 2001 Jeep Grand Cherokee

2 Answers

How can i use the 4 x 4 in my 2000 grand cherokee laredo (6 cyl) i dont have the owners manual and i dont know how to use my 4x4 on snow or something like that


With the Jeep in park, move the left shifter to 4 wheel drive. Proceed to put right shifter into drive, proceed to drive. Only use 4wheel drive when neccessary...ie...snow, mud, use 4 wheel lo in steep incline or when really bogged down.

Hope this helps

Jul 26, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Need an owner's manual for a 2000 "JEEP GRAND CHEROKEE" this one is a straight six cylinder.


The Owners Manual you can find in Jeep.com, review the Owners Section; also, here can find the Service Manual for Jeep.

Hope helped.

Nov 01, 2009 | 2000 Jeep Grand Cherokee

1 Answer

I am looking for a 1999 jeep grand cherokee owners manual to download


Jeep Grand Cherokee 1999-2004 also called WJ, about this model can check the information there: Jeep WJ 2000 Electrocnic Service Manual

Other details find in:
- Jeep Grand Cherokee WJ 2002 (all sections / spanish)
- WJ Jeep (several tips and DIY)

Good luck (remember rated this help).

Sep 02, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Open glass of liftgate 2000 jeep grand cherokee


there is a button outside on the liftgate where the licence plate light is . push button up to open glass

Apr 24, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

623 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...