Question about 2001 Ford Taurus

1 Answer

Where is the. 2001 Ford Taurus Engine Computer ECM locate

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 7,779 Answers

It's in the engine compartment, back passenger side, under cowl. here are instructions from autozone.com:


Removal & Installation
3.0L (VIN S) Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the three RH cowl panel clips and remove the RH cowl panel.
  5. Remove the clip on the water shield.
  6. Remove the three RH water shield screws and remove the RH water shield.
  7. Disconnect the powertrain control module (PCM) electrical connector and remove the gasket.
  8. Remove the retaining bolts and the PCM.
  9. To install, reverse the removal procedure.

3.0L (VIN U, 2) Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the three RH cowl panel clips and remove the RH cowl panel.
  5. Remove the clip on the water shield.
  6. Remove the three RH water shield screws and remove the RH water shield.
  7. Disconnect the evaporative emission (EVAP) canister purge valve return tube at the intake manifold and position aside.
  8. Disconnect the powertrain control module (PCM) electrical connector and remove the gasket.
  9. Remove the retaining bolts and the PCM.
  10. To install, reverse the removal procedure.

Posted on Oct 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change body control module on 2001 ford taurus


The BCM is located behind the glove box.Open Glove box, empty contents, grab sides of box and push inward a little bit and continue to open door. Once that's done there are 2 modules back there, #1 is ECM #2 is BCM, The BCM has a yellow clip on it and I think 5 connectors, make sure you mark down the location of where the connectors go for reassembly. Whatever you are doing make sure your BCM is the culprit because the BCM rarely ever goes bad on these cars.

Feb 15, 2015 | 2001 Ford Taurus

1 Answer

My ford Taurus won't start, I replaced the battery and now the anti theft system kills the engine


replacing battery more likely erase ECM memory.best to start vechicle let enginet idle until ECM relearn memory.your vechicle has to complete full drive cycle before ECM MEMORY return if not let dealership reset engine idle.

Jan 13, 2013 | 2001 Ford Taurus

1 Answer

My Ford Taurus Failed the inspection, we have replaced 1 oxygen sensor, but the reading still failed. Went to the Autozone & & did a reading came up with two codes P0430 & P0125, is this to...


PO125 means the ECM sees the engine is too cold to go into closed loop and runs rich for too long.
PO430 means the ECM doesn't like what it sees coming out the exhaust.
I would check the thermostat and make sure the engine is getting up to 195-200 degrees after 5 or 10 min of drive time, and if it is then check the temp sensor for the ECM to make sure it is reading the engine temp correctly.
Fixing the code 125 should take care of the code 430.

Jun 24, 2012 | 2001 Ford Taurus

1 Answer

Where is the ecm located at on a 2001 ford escape? I recently replaced the engine on my escape and my engine does not crank over. The theft light keeps flashing when I turn the ignition on. I'm thinking...


ECM is located in the engine compartment. Open the hood and before of you, in the called fire wall (up) you will see a maze of cables in a multipin conector. Unscrew it and you will find the Engine Control Module. Certainly, if you changed the engine and the ECM, the reprogramming must be executed.

Jan 06, 2011 | 2001 Ford Escape

2 Answers

No juice out of new altenator with new battey on 2001 taurus 3.0l


it's possible to get a bad "new" alternator. Get it tested.

Dec 31, 2010 | 2001 Ford Taurus

1 Answer

Where is the bank 1 sensor 1 on a 2001 ford taurus?


Hello
Bank one is the engine cylinder bank near the engine firewall (see diagram). The bank one sensor one is the Oxygen sensor (O2) located in the exhaust pipe just of the engine cylinder bank at rear and before the Catalytic Converters.

emissionwiz_19.gif

Dec 28, 2010 | 2001 Ford Taurus

2 Answers

Where is the Engine Control Computer located on a 1994 Taurus with a 3.0? and are there any memory cards that have to be taken from the old one and placed in the rebuilt one that i purchased?


Your ECC has no memory cards that have to be transfer to the other ECC, the ECC is a seal unit, just install, no reprogramming needs to be done, ECC is under hood, passenger side, rear engine area, above passenger side blower motor, mounted on fire wall.

Sep 15, 2010 | 1994 Ford Taurus

2 Answers

Where is the fuse located for the tranmission on a 2001 ford taurus


Hi!!

It should be in the fuse box next to the battery in the engine compartment. There is a fuse location diagram inside the fuse cover.

Good luck!! Don't forget to rate this post!!

Aug 18, 2010 | Ford Taurus Cars & Trucks

1 Answer

2001 ford taurus with check engine light on. code


Make sure you replaced the right one there are two sensor's for the coolant, one takes coolant temp and the other one runs the fans for the radiator. Both are located on drivers side of the block. 2 wire leads on each how ever both are different in sending readings to the computer.Both look just alike also. Just make sure you replaced the right one. Or replace both.

Sep 15, 2009 | 2001 Ford Taurus

1 Answer

ECM Testing


do a code scan 1st-if no problems then hav computer analysed-they r usually trouble free systems

Sep 06, 2009 | 2001 Ford Taurus

Not finding what you are looking for?
2001 Ford Taurus Logo

2,225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...