Question about 1995 Chevrolet Blazer

2 Answers

I lost the key to my husbands truck,how do you replace an inigation switch on 1995 Chevrolet Truck

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

Dont replace the switch take the registration to the Chevy dealer and they can cut a key by the vin number. The 17 digit number on the registration card.

Posted on Oct 15, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

1995-98 Models Fig. 1: Exploded view of the ignition and key alarm switch - 1996 C/K series I lost the key to my husbands truck,how do you - 87988g02.gif

  1. Remove the column shroud halves.
  2. Remove the column-to-dash attaching bolts and slowly lower the steering column, making sure that it is supported.
  3. Remove the multi function switch if necessary.
  4. Remove the key alarm switch, if equipped by gently prying the alarm switch retaining clip with a small screwdriver. Rotate the alarm switch 1?4 in. turn and remove. WARNING
    Extreme care is necessary to prevent damage to the collapsible column.
  5. Make sure that the switch is in the Lock position. If the lock cylinder is out, pull the switch rod up to the stop, then go down one detent.
  6. Disconnect the actuating rod from the switch.
  7. Remove the two screws and the switch. To install:
  8. Before installation, make sure the switch is in the Lock position.
  9. Attach the actuating rod to the switch.
  10. Install the switch using the original screws. Tighten the screws to 12 inch. lbs. (1.4 Nm).
  11. Install the key alarm switch, if equipped . Make sure the retaining clip is parallel to the lock cylinder. Rotate the alarm switch 1?4 in. turn until locked in place.
  12. Install the multi function switch if removed. CAUTION
    Use of screws that are too long could prevent the column from collapsing on impact.
  13. Replace the column. Tighten the nuts to 22 ft. lbs. (29 Nm); the bolts to 20 ft. lbs. (27 Nm).
  14. Install the column shroud halves. Fig. 2: Exploded view of the alarm switch removal - 1996 C/K-Series 87988g03.gif
prev.gif next.gif

Posted on Oct 15, 2010

  • Duane Wong
    Duane Wong Oct 15, 2010

    Click on the X's in order to view the diagrams from the chilton/haynes manual.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 blazer disconnected battery now alarm set, going off , no key fob. How do i reset?


that truck dont came whit factory alarm you have an aftermarket alarm unde the dash on the driver side you goint to find a small switch is the valet switch press the switch and turn ignition switch to on position that discobnect the alarm

May 22, 2015 | 1995 Chevrolet Blazer

1 Answer

Lost key had to replace switch with new switch know nothghing no start


tow truck to dealer ,to re-programme the key for immobilisor and have a spare done at the same time

Nov 20, 2010 | 1997 Chevrolet Cavalier

1 Answer

My transmission felt like it was slipping, then my truck, a 1995 GMC Sierra C1500,lost all power and dies, would not restart, all dash lights came on and sounded like flashers were on also with the key OUT...


if there is any corrosion between your battery cables and terminals you need to clean them real well i have a 1995 chevrolet silverado and i just delt with a similar starting problem there should be 2 cables attached to the positive (+) side pull the 2 cables apart and clean in between them real well the next cheapest thing woul be the starter the ignition switch is exspensive

Jun 29, 2010 | 1995 GMC Sierra C1500

1 Answer

Removal and installation of ignition. Lost only set of keys.


Go to any GM dealer ship with proof of ownership and the registration/title of this truck and keys can be made

May 29, 2009 | 1990 Chevrolet C1500

2 Answers

Ford 1995 F150 Truck. Turn ignition key off but Truck still runs


ignition switch electrical portoin above brake pedal on steering column

shack

Apr 14, 2009 | 2004 Ford F150

1 Answer

I lost my keys to my husband Chevy Tahoe 98. What do I do?? Can anyone help? I live in Germany...


You'll have to contact your nearest GM dealership and have them Code new keys for the truck. Can be a little costly but its the only way. The keys and FOB's are VIN specific.

Feb 18, 2009 | 1998 Chevrolet Tahoe

1 Answer

95 chev truck blows fuses


Your truck has a trailer hitch? Right! Check out the wiring! Frankster016

Oct 19, 2008 | 1995 Chevrolet C2500

Not finding what you are looking for?
Cars & Trucks Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...