Question about 2005 Cadillac Escalade

1 Answer

How do I replace third brakelight in 2005 Escalade

Posted by on

  • deelogan Feb 16, 2012

    There are 2 versions of this lamp. One version for the Escalade and one for the EXT (pick up). They are not interchangeable.

    There are no bulbs inside. There are circuit boards with LED's. Rebuilt units are available at www.ledfix.com

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 6,826 Answers

High-Mount Brake Light Removal & Installation Except Avalanche and Cadillac To Remove:

  1. Disconnect or remove the following:
    • Negative battery cable
    • Open the hatchback door
    • Pry open the center high-mounted stop lamp (CHMSL) access cover with a trim removal tool
    • Electrical connector
    • Screws and the CHMSL
To Install:
  1. Install or connect the following:
    • CHMSL with the screws. Tighten to 17 in lbs (2 Nm)
    • Electrical connector
    • The CHMSL access cover
    • Negative battery cable
Cadillac except Escalade EXT To Remove:
  1. Disconnect or remove the following:
    • Open the hatchback door
    • CHMSL retainers
    • Lower the hatchback door
    • Raise the CHMSL
    • Electrical connector and CHMSL
To Install:
  1. Install or connect the following:
    • Electrical connector and CHMSL
    • Open the hatchback door
    • Mounting screws into holes. Tighten to 10 in lbs (1.2 Nm)
    • Lower the hatchback door
Avalanche, Escalade EXT To Remove:
  1. Disconnect or remove the following:
    • Open the hatchback door
    • Rear compartment cover
    • Cargo box bridge center mounting screws
    • Panel assembly from the vehicle
    • Electrical connector.
    • CHMSL fasteners.
    • Remove the CHMSL from the cargo box bridge center bar.
To Install:
  1. Install or connect the following:
    • CHMSL to the cargo box bridge center bar with fasteners
    • Electrical connector to the CHMSL
    • Panel assembly to the vehicle. Tighten to 62 in lbs (7 Nm)
    • Cargo box bridge center
    • Rear compartment cover
How do I replace third - prev.gif next.gif

Posted on Oct 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change the third brakelight bulb on a 2011 Kia Sorento


take the screws out and replace the bulb and done put it back together and your done

Jan 19, 2015 | 2011 Kia Sorento 3.5

1 Answer

Third brakelight cargo lights not coming on on my 2014 silverado


Take the lens off of the light and change the bulb, it is probably burnt out.

Jul 03, 2014 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

How do you change the third brakelight led board on a 2005 kia sportage


how do you remove the left valve cover on a 2004 kia sorento 6 cylender

Nov 26, 2013 | 2005 Kia Sorento

1 Answer

Fuse box for 2005 Cadillac Escalade Ext


On this website you find fuse box diagram and description for Cadillac Escalade mk2 (2005)

Cadillac Escalade mk2 Second Generation 2005 fuse box diagram Auto Genius

Feb 17, 2012 | 2005 Cadillac Escalade Ext

1 Answer

Oil gauge reads 0. How to replace oil sending unit on 2005 escalade


First, drain the engine's oil.
Second, disconnect the electrical connector from the sending unit. (usually one small wire with a push on/pull off connector)
Third, use a socket which fits over the (usually six) flat sides of the sending unit.
This may be a standard socket, OR,
You may need a special socket to remove the sending unit.

Mar 10, 2011 | Cadillac Escalade Cars & Trucks

2 Answers

Need to know a in-dash DVD player that could replace the 6 disc CD changer in a 2005 Escalade.


any idea on how to get sound on the dvd player. i have a '03 escalade. video works, no sound

Oct 02, 2009 | 2005 Cadillac Escalade

1 Answer

How to remove and replace upper brake light on 2002 GMC Yukon.


Problem, which has been fixed, was with a 2002 Yukon, not a 2004 Escalade. Removing two screws below the upper or third brake light allows you to remove and replace the LED assembly.

Feb 17, 2009 | 2004 Cadillac Escalade

1 Answer

Having trouble shifting out of park... no problem shifting between gears.


I had this problem on a different type of vehicle and the solution was to replace the brake switch down near the brake pedal...This switch activates the brakelights and signals that the brake is engaged before allowing the transmission to come out of park...

Aug 08, 2008 | 2003 Cadillac Escalade

1 Answer

1994 Ford F-150: third brakelight


you have to peel the molding away from the truck on the outside and then change it then remold it

May 24, 2008 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
2005 Cadillac Escalade Logo

1,537 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...