Question about Mercedes-Benz Sprinter

Open Question

Intake Manifold runner control **** closed bank 1a, how do we proceed?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Hrnsly
  • 154 Answers

SOURCE: Intake manifold runner control stuck closed?

you don't have to replaced the manifold just the runner control. see this all the time at work the part is about 175.00 and an hour and a half to install. your local dealer should be able to fix this for you

Posted on Aug 07, 2009

Ad
jturcotte
  • 8743 Answers

SOURCE: intake manifold runner control stuck

left rear of intake manifold, there should be a vacuum operated shaft that turns these throttle plates. You'll have to troubleshoot reason. Try turning shaft by hand. There is a vacuum switch that runs vacuum to both banks. I think it's behind the engine nearer the firewall.

Posted on Sep 01, 2010

warlock61
  • 659 Answers

SOURCE: i have code 1538 on my check engine for 1998 ford windstar ,does

on the passenger side of the engine you will see 2 small metal rods at the top of the engine just below the intake manifold there are little white clips that hold the rods on these clips usually break and the rods come off

Posted on Mar 28, 2009

  • 14036 Answers

SOURCE: 1998 ford windstar 3.8 with code p1538. Is this a

LOOKING IN CODE BOOK.POSSIBLE CAUSE TO YOUR PROBLEM THE IMRC COULD BE STUCK OPEN.OR THE IMRC ACTUATOR IS DAMAGED OR HAS FAILED.ALSO THE IMRC MONITOR SIGNAL CIRCUIT COULD BE SHORTED TO POWER GROUND OR SHORTED TO SIGNAL GROUND RETURN.

Posted on Oct 23, 2009

  • 862 Answers

SOURCE: Generic code PO171 system 2 lean bank 1 generic

This can be caused by a faulty mass air flow sensor

Posted on Jul 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Ford Fusion 4 cyl.Engine light is on.Did diagnostic scan and it read P2004 Intake manifold runner bank 1a. There are 2 of these but dont know which one is bank 1a.


On a 2006 Ford Fusion with the 4 cylinder, there will only be one IMRC actuator. The V6 model has two. There is a solenoid and an actuator. You should check both of these for proper operation. The solenoid should click when it receives power and ground, and it controls vacuum to the actuator. The actuator should move when you apply or remove vacuum.
Also, when testing the actuator, it often takes more vacuum than you can produce with your mouth, so that is not an accurate test.

Oct 12, 2017 | Ford Cars & Trucks

1 Answer

What is an IMRC valve


IMRC stands for intake manifold runner controller. It is used for emission control and performance. your intake manifold has plates inside that are connected to a rod and tghe connected to the control motor. each bank of the engine can be opened and closed by the motor depending on engine load and other things.

Sep 11, 2016 | Cars & Trucks

2 Answers

2008 dodge avenger code p2004


Intake Manifold runner control stuck open - bank one:
- Intake Manifold Runner Binding Or Sticking
- Faulty Manifold flow valve
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection

There is a factory service bulletin for this problem for 2007-2008 Dodge Avengers. (JS)

Sep 22, 2015 | Dodge Cars & Trucks

1 Answer

How to fix code p2004 on 2005 ford focus


you code is here

P2004 Ford Intake Manifold Runner Control Stuck Open Bank 1


Possible causes - Intake Manifold Runner Control (IMRC) monitor signal shorted to power
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Intake Manifold Runner Control (IMRC) solenoid
- Damage Powertrain Control Module (PCM)
- Blocked vacuum hoses
alt="What does this mean?"> What does this mean? Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P2004 Ford Description The P2004 is set when the Intake Manifold Runner Control (IMRC) is commanded closed by the Powertrain Control Module (PCM), but the IMRC indicates open.


Read more: http://engine-codes.com/p2004_ford.html#ixzz3lke1SreV

Sep 14, 2015 | Ford Cars & Trucks

1 Answer

2004 ford f 150 5.4 3V pulled intake fixed vac hose came off replaced imrc & still show intake runner control closed bank 1 Still has no power when I get in it to pass something any ideas?


Is your check engine light on ? Any codes ?

There are three basic types of intake air sub-systems:


  • Intake Manifold Runner Control (IMRC) electric actuated system

  • Intake Manifold Swirl Control (IMSC) vacuum actuated system

  • Intake Manifold Tuning Valve (IMTV)

These subsystems are used to provide increased intake airflow to improve torque, emissions and performance. The overall quantity of air metered to the engine is controlled by the throttle body.

Intake Manifold Runner Control (IMRC) Electric Actuated System
The Intake Manifold Runner Control (IMRC) Electric Actuated system (Figure 107) consists of a remote mounted motorized actuator with an attaching cable for each housing on each bank. Some applications will use one cable for both banks. The cable or linkage attaches to the housing butterfly plate levers. The 2.0L (2V) Focus IMRC uses a motorized actuator mounted directly to a single housing without the use of a cable. Each IMRC housing is an aluminum casting with two intake air passages for each cylinder. One passage is always open and the other is opened and closed with a butterfly valve plate. The housing uses a return spring to hold the butterfly valve plates closed. The motorized actuator houses an internal switch or switches, depending on the application, to provide feedback to the PCM indicating cable and butterfly valve plate position.



Below approximately 3000 rpm, the motorized actuator will not be energized. This will allow the cable to fully extend and the butterfly valve plates to remain closed. Above approximately 3000 rpm, the motorized actuator will be energized. The attaching cable will pull the butterfly valve plates into the open position. Some vehicles will activate the IMRC near 1500 rpm.



WARNING: SUBSTANTIAL OPENING AND CLOSING TORQUE IS APPLIED BY THIS SYSTEM. TO PREVENT INJURY, BE CAREFUL TO KEEP FINGERS AWAY FROM LEVER MECHANISMS WHEN ACTUATED.




  1. The PCM uses the TP sensor and CKP signals to determine activation of the IMRC system. There must be a positive change in voltage from the TP sensor along with the increase in rpm to open the valve plates.




  1. The PCM uses the information from the input signals to control the IMRC motorized actuator based upon rpm and changes in throttle position.




  1. The PCM energizes the actuator to pull the butterfly plates open with the cable(s) or linkage.




  1. The IMRC housing contains butterfly plates to allow increased air flow.

Jun 29, 2015 | Ford Cars & Trucks

1 Answer

Chhrysler sebring 2007 2.4 litter getting code p2004 intak manifold runner control how do you fix it


code p2004 refers to intake manifold air control actuator bank 1---actuator stuck open===causes --wiring--intake manifold air control actuator --mechanical fault.
also refers to intake manifold air control solenoid bank 1 solenoid stuck open===causes--wiring intake manifold air control solenoid --- mechanical fault
you may be able to remove and clean the units to ensure they move freely otherwise replace them

Dec 31, 2013 | Cars & Trucks

1 Answer

P2006 ford f150


This Code means that the Intake Runner Control on Bank One is stuck closed. An intake runner is a part which acts like a gate and diverts airflow inside the Intake manifold.

Some have control rods which attach with plastic clips and the clips break causing the control rod to unseat in its place. They may use solenoids that are electric or Vacuum controlled and the rods on these devices are what moves the runners.

Often you can take the intake manifold off and clean the runner or reattach the rods.

Please rate my info.

Jan 18, 2013 | 2004 Ford F150

1 Answer

Generic code PO171 system 2 lean bank 1 generic


This can be caused by a faulty mass air flow sensor

Jul 06, 2010 | 1999 Ford Taurus

3 Answers

1998 ford windstar 3.8 with code p1538. Is this a


LOOKING IN CODE BOOK.POSSIBLE CAUSE TO YOUR PROBLEM THE IMRC COULD BE STUCK OPEN.OR THE IMRC ACTUATOR IS DAMAGED OR HAS FAILED.ALSO THE IMRC MONITOR SIGNAL CIRCUIT COULD BE SHORTED TO POWER GROUND OR SHORTED TO SIGNAL GROUND RETURN.

Oct 23, 2009 | 1998 Ford Windstar

1 Answer

2003 ford ranger dtc code index


hi there this code is a common problem with this engine
the dtc code p2004 is related intake manifold runner control it is stuck open bank 1a .
you need to replace controll switch

Jun 17, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

586 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77186 Answers

Joseph Prosser

Level 3 Expert

771 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...