Question about Volvo 940

Open Question

I would like a diagram for the engine on a 940 volvo diesel.Specifically the connection from the camshaft to the camshaft pulley at the rear of the engine Many Thanks Paul

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 80 Answers

SOURCE: volvo 940 turbo oil control valve location

take off pipe going to the intercooler from the turbo see if oil is found and clean then other pipe from incooler check it .if oil is found .drain oil in intercooler .you have an oil leak from the turbo this is why you will have light on far left of dash

Posted on Apr 28, 2009

  • 80 Answers

SOURCE: volvo 940 turbo diesel estate won't start

check the large relay in the fuse box and push it down it works a number things

Posted on May 04, 2009

emissionwiz
  • 75108 Answers

SOURCE: 1992 Volvo 960 Broken timing belt

IF U BROKE THIS BELT WHILE DRIVING U HAVE BENT THE VALVES IN THE ENGINE, THIS IS WHAT IS CALLED AN INTERFERENCE DESIGN ENGINE, THAT MEANS WHEN THE TIMING BELT BREAKS THE PISTONS HIT THE ENGINES VALVES

Posted on Nov 11, 2009

Testimonial: "THanks - was not able to accept this last answer, but thankfully I found another way to say THANKS. That notch was suspicious!"

sandman357
  • 236 Answers

SOURCE: replacing fuel pump on 1992 Volvo 940

look in autozone, look up the part n then click on "view job diagram" hope that helps

Posted on Feb 28, 2010

  • 23 Answers

SOURCE: Hi, need diagram of 1997 VW Polo diesel gearbox

Hi Paul, Most of these gearboxes were almost identical for vw during the those years, some manuals are available free from this site
http://carservicemanuals.blogspot.com/search/label/Volkswagen
Hope it will help you out.
Dave

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram of proper installation of timing tensioner pulley


you do not have a safe engine if 1994 is this the red block engine the last red block safe engine was in 1993.

Feb 09, 2013 | 1994 Volvo 940

1 Answer

Belt Routing Diagrams


For belt routing diagrams of 1992 volvo 940. Click the link below:--- http://technoanswers.blogspot.com/2011/10/timing-belt-diagram-for-1992-volvo-940.html ----------- Its with proper detail and procedure. ----- This will help.Thanks.Helpmech.

Oct 24, 2011 | 1992 Volvo 940

1 Answer

Need diagram of timing marks 95volvo940


zjlimited_2080.jpg

Fig. 9: Pulley alignment marks for timing belt replacement


zjlimited_2081.jpg

Fig. 10: Line up the camshaft pulleys with the marks on the engine mounting plate

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.
Jose.

Oct 23, 2011 | 1995 Volvo 940

1 Answer

Belt_Routing_Diagrams 95 volvo 940 non turbo


Do not take it off before you are ready with the new one.
Turn the crankshaft until the engine is at tdc. The key on the pulley should be at the top.
Use a little paint brush and a little paint,and mark a couple of teeth on the camshaft pulley and the belt in between these teeth. if there are any other pulleys using the belt, do the same for them.
Do the same for the crank pulley. Take off the belt, try not to move anything. Count the belt teeth between these two marks and transfere them to the new belt. Now fit the belt in the exact places that the old one came off. Do this very carefully and you should have no problems.

Oct 23, 2011 | Cars & Trucks

1 Answer

Radio wire colors


1994 Volvo 940 Car Audio Wire Diagram
Car Radio Battery Constant 12v+ Wire: Yellow
Car Radio Accessory Switched 12v+ Wire: Red
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Light Orange
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: 5 1/4′
Car Audio Front Speakers Location: Doors
Left Front Speaker Positive Wire (+): Blue/Yellow
Left Front Speaker Negative Wire (-): White
Right Front Speaker Positive Wire (+): Gray/White
Right Front Speaker Negative Wire (-): Gray
Car Audio Rear Speakers Size: 6′ x 9′
Car Audio Rear Speakers Location: Rear Deck
Left Rear Speaker Positive Wire (+): Yellow/Brown
Left Rear Speaker Negative Wire (-): Yellow/Green
Right Rear Speaker Positive Wire (+): Green/Brown
Right Rear Speaker Negative Wire (-): Green

Hope helps (remember rated this) TY for use Fixya.

Jun 03, 2010 | 1994 Volvo 940

2 Answers

How to change water pump on toyota sienna


3.0L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Wiper and blade assembly Top cowl seal and panel Window washer hoses, from the ventilator louvers Left and right ventilator louvers Heater air duct Timing belt
  5. Mark the left and right camshaft pulleys with a touch of paint.
  6. Remove or disconnect the following:
    NOTE Be sure not to mix up the pulleys.
    Right and left camshaft pulleys bolts Pulleys from the engine
    No. 2 idler pulley by removing the bolt 3 clamps and engine wire from the rear timing belt cover 6 No. 3 timing belt cover-to-engine bolts Water pump nuts/bolts Water pump and gasket from the engine

    9c53b11.jpg
    Fig. Exploded view of the components to gain access to the water pump-3.0L engine


    cf2cc65.jpg
    Fig. Exploded view of the water pump and related components-3.0L engine

To install:
  1. Check that the water pump turns smoothly. Also check the air hole for coolant leakage.
  2. Apply liquid sealer to the gasket, water pump and engine block.
  3. Install or connect the following:
    NOTE After tightening the bolt, be sure the idler pulley moves smoothly.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    Water pump, using a new gasket. Tighten the nuts/bolts to 53 inch lbs. (6 Nm). Rear timing belt cover. Tighten the 6 bolts to 74 inch lbs. (9 Nm). Engine wire with the 3 clamps to the rear timing belt cover No. 2 idler pulley. Tighten the bolt to 32 ft. lbs. (43 Nm).
    Right-hand camshaft pulley, with the flange side outward.
    Tighten the camshaft bolt to 65 ft. lbs. (88 Nm), using the removal tools Left-hand camshaft pulley, with the flange side inward.
    Tighten the camshaft bolt to 94 ft. lbs. (125 Nm), using the removal tools Timing belt
  4. Fill the engine coolant.
  5. Install or connect the following:
    Heater air duct Left and right ventilator louvers Window washer hoses to the ventilator louvers Top cowl seal and panel Wiper and blade assembly Negative battery cable
  6. Start the engine.
  7. Top off the engine coolant and check for leaks.

Hope this help.

Mar 23, 2010 | 2004 Toyota Sienna

1 Answer

Volvo 940 turbo diesel estate won't start


check the large relay in the fuse box and push it down it works a number things

Apr 21, 2009 | 1994 Volvo 940

1 Answer

Need a wiring diagram for Volvo 940S 1993


Constant 12V+ Yellow Switched 12V+ Red Ground Black Illumination Light Orange Dimmer n/a Antenna Left Rear Front Speakers 5 1/4" Doors Left Front (+) Blue/Yellow Left Front (-) White Right Front (+) Gray/White Right Front (-) Gray Rear Speakers 6" x 9" Rear Deck Left Rear (+) Yellow/Brown Left Rear (-) Yellow/Green Right Rear (+) Green/Brown Right Rear (-) Green

Dec 26, 2008 | 1994 Volvo 940

1 Answer

1994 Volvo 940 install timing belt


TAKE FRONT COVER OFF(AFTER REMOVING FAN, BELT S, PULLEY AND FAN SHROUD).THEN REMOVE CRANK SHAFT PULLEY. WHEN COVER IS REMOVED YOU'LL SEE 3 SPROKETS, SUGGEST TO BRING CRANK TO TOP DEAD CENTER UNTIL YOU SEE ALL 3 MARKS FOR THE TIMING BELT. REMOVE BELT/INSTALL NEW AND REVERSE PROCEDURE.

Dec 23, 2008 | 1994 Volvo 940

2 Answers

1994 Volvo 940 Station Wagon timing belt


I hope you've solved the problem by now, but there are alignment marks on the crank shaft (top pulley), idler (lower side), and cam shaft (smaller, bottom pulley) which should be aligned with stationary marks on the timing belt rear cover.

The belt has marks that align with the aforementioned marks (lines). The double marks on the belt align with the camshaft marks and the single marks with the others.

Loosen the tensioner clamp (nut) to allow the spring loaded tensioner to press on the belt and retighten the nut.

Rotate the crank shaft (clockwise, probably two revolutions) and make sure the pulley marks realign to the marks on the cover (they don't have to realign with the marks on the belt).

Rotate the crank shaft a full revolution once the belt is on and check that alignment is preserved.

Periodically loosen and retension the tensioner nut (access through a hole in the cover) to ensure that tension is maintained as the belt relaxes.

Oct 25, 2008 | 1994 Volvo 940

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...