Question about 2006 Jaguar XJ8
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
If your bonnet will not release, there is a rubber plug inside fender located up in
the wheel well under the latch. Remove the plug, stick a screwdriver up and pry the latch
back. The hood / bonnet will open.
Posted on Mar 01, 2010
SOURCE: 2004 xj8 jaguar a/c fan
there is a relay on the firewall for that but check the fuses first to make sure its not blown...if its not blown you can run a jumper wire to test the motor itself to see if it works or not.
Posted on Aug 10, 2008
check out with your dealer as you might have a recall to fix this problem.
Overheating - Cooling Fans Inoperative - Replace Module Prior To Retailing - Service Action S932
This Service Action Applies to Vehicles That Have Not Been Retailed
The cooling fan module on X-TYPE vehicles may fail under certain circumstances. There are various root causes but the design and quality of the printed circuit board within the cooling fan module are the most significant. The NAND gate used in the circuit is detective causing multiple failure modes, this can result in high engine temperature and overheating due to the cooling fans not operating.
A change has been implemented in production from VIN C91720. On these vehicles a 'Philips' printed circuit board has been used that has a modified voltage spike protection strategy.
To prevent customers from experiencing this issue, install the latest specification cooling fan module on 2002-03 MY X-TYPE vehicles within the above VIN range that have not been retailed.
1. Install new cooling fan module (see Workshop Manual, JTIS CD ROM, section: 303-03, SRO 26.25.38).
Warranty claims should be submitted quoting S932 in place of the warranty fault code together with SRO: 26.25.38 and the relevant part number. This will result in a labor time allowance of 0.8 hours to replace the cooling fan module and payment for the part used. Should the vehicle be brought back into the workshop for this action alone to be undertaken, an additional labor time allowance of 0.1 hours can be claimed quoting SRO: 10.10.10 for drive in/drive out.
Warranty claims should be submitted quoting the information found in the table. This will result in payment of the stated time and, where applicable, parts/miscellaneous expense codes.
The options that allow for drive in/drive out may only be claimed when the vehicle has been brought in to the workshop for this action alone to be undertaken.
The SROs and parts items listed above have been included for information only, there will be no requirement to enter the parts or SROs onto the claim.
NOTE: Always perform a DDW claim search first to determine whether this service action has been performed on this vehicle. The warranty selection under the vehicle inquiry will give a listing of all claims against the vehicle. If this service action number appears in the program code field, do not perform this service action.
Posted on Jan 19, 2009
It is behind the alternator. If you disconnect the top alternator bolt and then the lead to the alternator, and loosen the bottom bolt, you can swing the alternator towards the passenger side and see the sensor. You obviously have to remove the serpentine belt to move the alternator.
Posted on Oct 24, 2009
Tips for a great answer:
Sep 25, 2015 | Cars & Trucks
May 02, 2014 | 2006 Jaguar XJ8
Aug 19, 2013 | Jaguar Cars & Trucks
Sep 05, 2011 | 2001 Jaguar XJ8
Jun 19, 2011 | 2006 Jaguar XJ8
May 03, 2010 | 2001 Jaguar XJ8
Dec 22, 2008 | 2004 Jaguar XK8
Nov 28, 2008 | 2007 Jaguar XJ8L Sedan
1,000 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: