Question about 2005 Nissan Maxima

Open Question

HOW DO YOU REMOVE THE FRONT HUB ASSEMBLY FROM A 2005 NISSAN MAXIMA???? IM AT A LOSS HERE

Posted by on

  • 2 more comments 
  • Anonymous Oct 16, 2010

    You can't figure out how to unbolt it?
    Better to have it done by a shop

  • tpatterso655 Oct 18, 2010

    IT DOESNT UNBOLT..... ITS A PRESS IN HUB. YOU PRESS THE HUB IN AND THEN PRESS THE BEARINGS AND RACES IN BEHIND THAT. THANKS FOR THE TIP

  • Anonymous Oct 18, 2010

    There are tools for that ,if everything is pressed together.
    They are special for that type of work and too expensive to buy
    Have it done at at repair shop,with the correct equipment/tools

  • tpatterso655 Oct 19, 2010

    well youre just a wealth of knowledge. thanks. Its called an arbor press and theres nothing special about it.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Front End Noise in 2005 Nissan, Maxima

It could be a bad wheel speed sensor..causing your anti lock system to pulse.
I have an 06 and have just developed very bad issues with my anti lock brakes.
They began pulsing at slow stops on dry pavement, and then clunking, and after I released the peddle sometimes it will contiue to make a loud tapping noise.

Posted on Jul 14, 2008

  • 55 Answers

SOURCE: 2005 nissan maxima cd player

Get yourself a Maxima service manual. It will give U instructions on doing alot of re[airs for the car, including taking dash apart.

Hope this ads your problem

Matt

Posted on Dec 16, 2008

  • 383 Answers

SOURCE: 2005 Nissan Maxima SE Fog light replacement

jorgeva: on the driver's side to gain access, you must remove the air cleaner assembly. At that point, you can see the back of the light which has a plastic cap. Rotate this "counter clockwise" and you can pull it back from the back of the lamp housing. From there you will see how the bulb it self is plugged in, which is obvious. Unplug it. There is a "spring "like latch retainer to hold the bulb in place. Unlatch it, remove the bulb and install the new bulb.
CAUTION!!!!!!! DO NOT TOUCH THE GLASS AREA OF THE NEW BULB! Only handle the rear section. Reassemble in the reverse order.
The right side will require the removal of the windshield washer tank.
I trust this will have answered your question. If you would, let me or FIXYA know if I have solved your problem......

Posted on Apr 18, 2009

  • 22 Answers

SOURCE: How do you dismantle the front hub assembly on 96

Remove the wheel, remove the brake caliper and the hub cover you'll need to remove and remove the wheel bearings in there. then the rotor/hub will come out as one.

Posted on Apr 27, 2009

  • 103 Answers

SOURCE: no sparks from spark plugs in the 97 nissan maxima wont start up

This car has seporate coil packs for each cylinder, have you tried swapping the front bad one with a good one to see if they switch ?
The engine you just put in may have come with some blown coils.
Hope this helps
Sam

Posted on May 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to remove front axles from hub what size socket is used


A size 36mm impact socket is used to remove the front axle nut from the hub.

Feb 26, 2011 | 1990 Nissan Maxima

1 Answer

Where is the inner wheel bearing located on a Nissan Maxima


if its the front its in the hub assembly and should be replaced as a unit. if it is the rear and it is drum brakes when you remove the drum it is also a hub assembly. hope this helps

Feb 03, 2011 | 1996 Nissan Maxima

1 Answer

I need to know where may I find the manual or instructions on replacing a 2005 nissan maxima wheel bearing?


The front wheel bearing is a pressed in bearing. It will require the services of a machine shop to press out the old bearing and press in the new one. What you will need to do is separate the knuckle from the front suspension of the car.

Remove the axle nut. Separate the outer tie rod from the knuckle. Remove the caliper and the rotor. Separate the lower ball joint from the knuckle. Remove the two bolts that hold the knuckle to the strut. Once the knuckle is free you can take it into a machine shop or some auto shops and have the bearing pressed in and out. I will add that it is also common for the front hub (the part that has the wheel studs in it) to wear out on these as well so don't be surprised if they tell you you need one.

Nov 08, 2010 | 2005 Nissan Maxima

1 Answer

How do you remove the front wheel hub?


Hope this diagram helps:

Exploded view of the steering knuckle and hub assembly


f891ebe.gif

May 04, 2010 | 1995 Nissan Maxima

1 Answer

2005 dodge 2wd 3500 front hub assembley.. how do i


there are three mounting bolts behind the wheel studs
remove the bolts
remove abs sensor
slide the hub out of steering knuckle

Mar 05, 2010 | 2005 Dodge Ram 3500

1 Answer

How to repair/ replace a front bearing on a nissan maxima?


You have to remove the knuckle and get the old bearing and hub pressed out and have the new one pressed in.

Sep 30, 2009 | 1995 Nissan Maxima

1 Answer

How do you dismantle the front hub assembly on 96 nissan safariNissan safari 1996


Remove the wheel, remove the brake caliper and the hub cover you'll need to remove and remove the wheel bearings in there. then the rotor/hub will come out as one.

Apr 24, 2009 | 1996 Nissan Pathfinder

1 Answer

2000 Nissan Maxima rear axle bearings are humming, I want to change them. Do I need special tools such as a bearing puller?


rapeck: The Maxima rear axle bearings are manufactured as a hub assembly. There is a ring for the ABS which is fitted to the hub which must be removed and installed on the replacement hub.
A puller or other method is used to remove it and install it.
Aside from that, taking the caliper off and hanging it, removing the brake rotor and removing the axle nut. Torquing the axle nut is necessary. so there you have it...
  • Any other questions?

Apr 24, 2009 | 2000 Nissan Maxima

2 Answers

HOW TO REMOVE THE REAR BRAKE LIGHT LENS TO REPLACE THE BULB


how do i remove my tail light assembly out of my 2005 nissan maxima

Nov 18, 2008 | 2004 Nissan Maxima

Not finding what you are looking for?
2005 Nissan Maxima Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...