Question about 1994 Isuzu Trooper

1 Answer

Where can i find timing mark for camshaft and injection pump

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,584 Answers

Under the cam covers

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know where the timing marks are on a 96 4wd isuzu rodeo. CAN ANYBODY HELP ME PLEASE?



  • I hope you get this, I was going to go to bed until I noticed how bad you were needing some timing marks :)

  • Injection pump and camshaft alignment marks-diesel engine
ironfist109_302.jpg

ironfist109_303.jpg

  • Tensioner pulley bolt sequence (diesel)


ironfist109_304.jpg


  • Crankshaft sprocket timing mark-2.3L and 2.6L engine
ironfist109_305.jpg

  • Camshaft sprocket timing mark-2.3L and 2.6L engine
ironfist109_306.jpg
  • Timing belt installation sequence-2.3L and 2.6L engines
ironfist109_307.jpg
  • Timing belt tensioner lockbolt-2.3L and 2.6L engines
ironfist109_308.jpg

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 06, 2011 | 1996 Isuzu Rodeo

1 Answer

1996 jeep grand cherokee timing marks diagram


Click over image for zoom...

zjlimited_1982.jpg

Fig. 3: Camshaft and injection pump timing marks aligned

Feel free to contact uc if you need aditional details or some specific section of the Grand Cherokee Service Manual

Hope helps.
Hope helps.

Oct 04, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Timing marks trooper 1985 mod dlx turbo diesel


Refer to Figures 1,2,3,4 when performing 17-step timing procedure for 1981-1985 Diesel Engines.

Fig 1. Injection pump and camshaft alignment marks - Diesel engine.

archaeology_66.jpg


Fig 2. Removing the timing belt holder - Diesel engine.

archaeology_67.jpg

Fig 3. Injection pump alignment marks - Diesel engine.

archaeology_68.jpg

Fig 4. Tensioiner Pulley Bolt Sequence - Diesel engine.

archaeology_69.jpg

Procedure - Timing Belt replacement.

1. Disconnect the negative battery cable. Drain the cooling system.

CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

2. Remove the timing belt cover. Remove the injection pump sprocket flange.

3. Using a prybar, remove the tension spring from the timing belt tensioner.

When removing the tension spring, avoid using excessive force for the spring may become distorted.

4. Remove the tensioner pulley bolt and the pulley.

5. Remove the timing belt and discard it.

To install:

6. Rotate the crankshaft to bring the No. 1 piston to TDC of the compression stroke.

7. Align the timing marks on the injection pump sprocket with the camshaft sprocket; the marks must be facing each other.

8. Using a new timing belt, install it in the following sequence: crankshaft sprocket, camshaft sprocket and the injection pump sprocket; the slack must be between the injection pump and camshaft sprockets.

9. Install the tension center and the tension pulley so the end of the tension center is fitted against both pins on the timing pulley housing.

10. Hand tighten the nut so the tension pulley can be rotated freely.

11. Install the tension spring and semi-tighten the pulley nut to 22-36 ft. lbs. (30-48 Nm).

12. Rotate the crankshaft 2 full turns clockwise to seat the belt and further turn the crankshaft 90° beyond TDC to settle the injection pump.

13. Loosen the tension pulley nut to take up the timing belt slack. Tighten the tension pulley nut to 79-94 ft. lbs. (108-128 Nm).

14. Install the injection pump sprocket flange; the hole in the outer circumference of the flange should be aligned with the triangular timing mark on the injection pump sprocket.

15. Rotate the crankshaft 2 full turns clockwise to bring the No. 1 piston to TDC of the compression stroke. Make sure the triangular timing mark on the timing sprocket is aligned with the hole in the flange, then, measure the timing belt tension; it should be 33-55 lbs.

16. Install the timing belt cover.

17. Connect the negative battery cable.

Jul 04, 2011 | 1995 Isuzu Trooper

1 Answer

Hi, noticed a post of yours rear cambelt replacement on an a4 1.9 tdi ajm year 2000. Would be very grateful for any instructions. The car is stripped down ready for cambelt removing. Stuck on lining up...


Hi, I have pasted instructions below from autozone.com. The instructions call for the use of special tools. You can improvise with alternate tools, but please make sure your timing is right before closing the cover. Please let me know if you have questions, and thanks for using FixYa.

1.9L Diesel Engine
Some special tools are required to perform this procedure properly. A flat bar, VW tool 2065A is used to secure the camshaft in position. A pin, VW tool 2064 is used to fix the pump position while the timing belt is removed. The camshaft and pump work against spring pressure and will move out of position when the timing belt is removed. It is not difficult to find substitutes but do not remove the timing belt without these tools.

WARNING Do not turn the engine or camshaft with the timing belt removed. The pistons will contact the valves and cause internal engine damage.
  1. Disconnect the negative battery cable and remove the accessory drive belts, crankshaft pulley and the timing belt cover(s). Remove the camshaft cover and rubber plug at the back end of the camshaft.
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to Top Dead Center (TDC) of No. 1 piston. The mark on the camshaft sprocket should be aligned with the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the engine at TDC, insert the bar into the slot at the back of the camshaft. The bar rests on the cylinder head to will hold the camshaft in position.
  4. Insert the pin into the injection pump drive sprocket to hold the pump in position.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner counterclockwise to relieve the tension on the timing belt. Slide the timing belt from the sprockets.

    jturcotte_1820.gif

    Fig. Use the VW tool to lock the camshaft at TDC for timing belt replacement-Volkswagen 1.9L Diesel engines


    jturcotte_1821.gif

    Fig. Locking the injection pump with the VW tool as shown-Volkswagen 1.9L Diesel engines


To install:
  1. Install the new timing belt and adjust the tension so the belt can be twisted 45 degrees at the halfway point between the camshaft and pump sprockets. Tighten the tensioner nut to 33 ft. lbs. (45 Nm).
  2. Remove the holding tools.
  3. Turn the engine 2 full revolutions to return to TDC for the No. 1 cylinder. Recheck belt tension and timing mark alignment, readjust as required.
  4. Install the belt cover and accessory drive belts.
    NOTE If the belt is too tight, there will be a growling noise that rises and falls with engine speed.

Jun 11, 2011 | Audi A4 Cars & Trucks

1 Answer

Seat inca van 00 sdi 1.9 diesel.. tension polly came loose.. timing belt slipped.. I need to know how to reset it again. Where are the markings on the crank shaft and the cam shaft? Please attach any...


Timing belt set-up for a 2000 Seat Inca 1.9 SDi

1. Align the crankshaft timing marks on the flywheel / gearbox

tdisline_583.jpg
2. Remove the valve cover
3. Lock the camshaft

tdisline_584.jpg
4. Fit the injection pump locking pin

tdisline_585.jpg

5. Loosen the camshaft gearwheel bolt, 180 degrees. Use a wrench to counter-hold
6. Loosen the camshaft gearwheel while holding it in place

tdisline_586.jpg

7. Fit the timing belt in the sequence as shown in the below figure: a - b - c - d - e - f - g

tdisline_587.jpg

8. Fit the timing belt and camshaft gearwheel together
9. Turn the tensioner clockwise to align both marks

tdisline_588.jpg

10. Tighten the large bolt on the tensioner to a torque of 20 Nm
11. Check for correct fit
12. Lock the camshaft. Tighten the camshaft gearwheel bolts: 45 Nm. Use a wrench to counter-hold
13. Remove helping tools
14. Turn the engine two rotations by hand
15. Repeat the procedure if required
16. Fit the vacuum pump
17. Refit the crankshaft pulley. Tighten torque: 20 Nm + 20 degrees
18. Fit the timing belt cover
19. Refit the valve cover
20. Fit the ancillary drive belt
21. Refit the inlet air manifold hoses
22. Check the injection timing

Torque settings:
Camshaft gearwheel: 45 Nm
Tensioner pulley: 20 Nm
Crankshaft pulley: 20 Nm + 20 degrees

May 26, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

Hi ive got a 1996 isuzu bighorn ive attempted to change the timing belt but the injector pump pulley moved when i took the belt off. i put it back where i thort it was and tried a tooth either way but no...


Timing belt installation

1. Ensure locking bolts located correctly [4] & [5] in the picture below:

tdisline_32.jpg
CS = Crankshaft
CA = Camshaft
IP = Injection Pump

2. Ensure timing marks aligned [10].
3. Fit timing belt in clockwise direction, starting at crankshaft sprocket.

NOTE: "ISUZU" lettering on belt should be readable from front of engine.

4. Slacken tensioner pulley bolt [9]. Push tensioner pulley against belt.
5. Ensure belt is taut between injection pump sprocket and tensioner pulley as well as crankshaft sprocket and camshaft sprocket.
6. Position tensioner lever [8] against tensioner pulley housing.
7. Remove locking bolts from sprockets [4] & [5].
8. Apply a load of 10 ... 12 kg to tensioner lever. Use spring balance [11].
9. Tighten tensioner pulley bolt to 80 Nm.
10. Turn crankshaft slowly 45 degrees anti-clockwise. Use spring balance to tension belt.
11. Repeat tensioning procedure at 45 degrees intervals for one anti-clockwise turn of the crankshaft.

NOTE: DO NOT turn crankshaft clockwise during tensioning procedure!

12. Fit tensioner lever to original position. Tighten nuts [12].
13. Install: Injection Pump flange [6], Camshaft sprocket flange [7], and water pump pulley.
14. Install components in reverse order of removal & refill coolant.

tdisline_33.jpg
PLEASE DO RATE MY RESPONSE. THANKS!

Nov 27, 2010 | 1996 Isuzu Trooper

1 Answer

Where are the timing marks and how do u time a 1998 Pontiac Sunfire gt? I was told there are two 14mm holes for the two upper gears and a mark for the lowers. I had a hard time getting them to line up but...


hi, all newish cars have places for locking the engine, camshaft, injection pump. the camshaft groove is under the roker cover at the back (this is a flat bar and go's across the two camshafts). the injection pump locking pin normally pushes in the injection pump spocket, the front timming cover will need to be removed. the crankshaft locking pin normally locks-up No. 1 piston there is a bolt that must be removed.this is best done with the spark plugs OUT. ALL THESE LOCKING PINS AND BARS MUST BE REMOVED AND REPLACE THE BOLT FOR No,1 PISTON. method to install locking pin on No. 1 piston bolt locking pin and turn engine BY HAND ONLY BECAUSE YOU WILL DAMAGE CRANKSHAFT AND DO NOT FORSE it any more. once the No. 1 piston is locked check the camshaft and place the BAR. next is the injection pump push the locking pin into the sprocket. remember to REMOVE ALL LOCKING PINS AND BAR AND REPLACE BOLT FOR No. 1. p. s. you can put your own marks but is NOT RECOMENDED. i hope this is useful gerry

Sep 08, 2010 | 1998 Pontiac Sunfire

1 Answer

Camshaft timing mark crankshaft timing mark


Belt covers need to be on. Timing mark on crankshaft (while on compression stroke) should line up with TDC mark on cover. then Camshaft mark, needs to line up by looking through access hole of cover, and align mark on cam sprocket with pointer on inside of belt cover.

Oct 22, 2009 | 1987 Ford Ranger

1 Answer

How to install timing belt on 1998 vw beetle


Instructions
Things You'll Need: · Set of quarter-inch drive sockets Quarter-inch drive ratchet Set of half-inch drive sockets Half-inch drive air gun Set of metric wrenches Special tools for holding camshaft timing #2065-A and injection pump #2064

Step 1

Remove the accessory drive belts and the accessory drive belt tensioner. Remove the upper timing belt cover and the valve cover. Turn the crankshaft clockwise until the No.1 cylinder is atop, dead center, with the flywheel timing marks aligned.

Step 2

Install the special tool setting bar (#2065-A) on the rear of the camshaft. If it does not fit, turn the crankshaft once more and line up the timing marks again in the hole of the transmission housing.

Step 3

Insert locking pin #2064 into the injection pump to hold it in position. Remove the crankshaft pulley bolts, the crankshaft pulley and the lower timing belt cover. Loosen the tensioner pulley nut and allow the tensioner to move away from the belt. Loosely tighten the nut to hold the tensioner out of the way. Remove the top guide pulley and the timing belt.

Step 4

Make sure that the timing mark on the flywheel is lined up and that the camshaft setting bar and injection locking pin are in place. Loosen the camshaft bolt a half turn and tap the sprocket with a soft mallet to loosen it off its taper. The sprocket should move freely. Install the top guide pulley and torque to 18 foot pounds of torque.

Step 5

Install the new timing belt, starting on the right side and working counterclockwise. Keep the tension on the right nontensioned side. Loosen the tensioner pulley nut. Using the two-pin wrench, turn the tensioner pulley clockwise until the notch and raised mark are aligned. Torque the tensioner pulley nut to 15 foot pounds of torque. Make sure the flywheel timing mark is still aligned.

Step 6

Torque the camshaft bolt to 33 foot pounds of torque. Remove the locking pin from the injection pump and remove the camshaft setting bar. Turn the crankshaft two turns and check the alignment on the flywheel. Make sure that the setting bar can be inserted easily and that the injection pump locking pin can be inserted. Install all components in reverse order of removal and torque the crankshaft bolt to 18 foot pounds of torque.

My Recommendation - Pay an authorized VW mechanic $500 to replace the timing belt water pump an tensioner, and sleep better knowing that the job was done right. Just too many places for a novice car mechanic to screw up. jQuery('.article ol .image').each(function(i,e){ var $this = jQuery(this); $this.find('img').error(function(){ jQuery(this).remove(); $this.remove(); }); });

Oct 06, 2009 | 1998 Volkswagen Beetle

Not finding what you are looking for?
1994 Isuzu Trooper Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...