Question about 2007 Honda CR-V

1 Answer

How to remove tailgate cover

Actualy a 2008, but assume they are the same. Installing rear view camera. Need to remove the inside cover parts of the tailgate to install and route wiring. Any suggestions on how to remove them? Hopefully without damage. Note there are some small slots at several locations - but don't want fo force them. Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Most car all makes these days use push clips on the hidden panel side or visible screws or smaal cicular covers hidding the screw heads or a combination of clip and screw.pull the panel towards you inspect it has a lip at the window glass then push to the sky,

Posted on Nov 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why porsche cayenne 2009 rear view camera is not opening cover is stuck


As with most vehicles the rear window and tailgate gets covered in dirt, salt etc. which is thrown up from the rear wheels and by the wind swirling out and up. The cover on the camera needs cleaning and lubricated regularly. I washed the cover, dried it with high pressure air and lubricated it with a silicone spray. When I first did it, there was a fine dirt in the crevices that needed to be dug out. I used a small blade to scrap it out, then lubricated it. Good luck.

Aug 16, 2014 | 2009 Porsche Cayenne

1 Answer

Do how 2008 getz stop light globe change


Hi there,

There should be a cover directly behind the light inside the tailgate., All you need to do is remove this cover and you will have access to the rear of the light socket. Twist the light out anti clockwise and the globe will come out. Refit in the reverse order.

If you find it hard try it this way >

holding the assembly together, and yes a screwdriver is what you will need along with a little pressure at each side once you have pried each joint to stop them from popping back together.

May 12, 2014 | 2008 Hyundai Getz 1.3

1 Answer

Tailgate won't open


is this a RKE FOB only statement, and no keys tried?
all buttons tried? in car and the fob button?
Usually there are 3 ways, at least. Fob, real key and door switches.
the driver on some cars have a button to open all locks in car.


all ways, tired, inside and outside.?
id remove the inside tail gate, panel.
the lever to the lock is there. move the lock by hand iniside, i bet it opens now.


on most cars there is a child lock feature, its covered in the operators guide the fact there. read that. first.

wits end.?
id remove the inside tail gate, panel.
the lever to the lock is there. move the lock by hand inside, i bet it opens now.

Mar 13, 2014 | 2008 Jeep Grand Cherokee

1 Answer

Schematic diagram for parts of a Honda jazz 1.4 dsi 2008 please


Go to the dealer and have them bring up the exploded parts views for you on the area of the damage.

Oct 31, 2012 | Cars & Trucks

1 Answer

Escort 55 van rear door lock wont unlock with key


I assume you are referring to the tailgate door, so what likely happened is that either the door lock has something in it like a broken key, or dirt, or rust, etc. or perhaps the mechanism has failed.
Understand these parts are made as cheaply as possible, and are easy to break.
You may need to remove the riveted cover to look inside, and you may find a plastic clip broken, or the lock mechanism spoiled, or something else.
You do not need to re-rivet the cover, unless you have a pop-rivet tool.
You can also find some small screws that will reattach the cover. God bless your efforts.

Jan 31, 2012 | Cars & Trucks

1 Answer

Can hummer h3 tailgate be opened from inside? The rear door/tailgate handle just snapped off.


Yes you can open the tailgate from the inside,if you open the housing that holds the jack and wheel spanner then you will find the hatch to open the tail gate

Nov 07, 2011 | 2008 Hummer H3

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

I need to remove 2004 toyota sequoia tailgate door panel to get access the rear tail light to install a backup camera. I don't see any obvious removal points.


Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.

Remove the bolt and the strap/

Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.

Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.

Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.

Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)

The license plate trim panel, should you need to remove it, requires remoaval of the license plate.

Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.

Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)

Sep 20, 2009 | 2003 Toyota Sequoia

Not finding what you are looking for?
2007 Honda CR-V Logo

Related Topics:

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...