Question about 2002 Suzuki XL-7

1 Answer

Clutch has to be pushed all the way down and it is very hard to put gears in at a stop. Sometimes you have to shove the gear in and forget about reverse. Is it that i need to get the clutch adjusted or replaced?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

With any luck ajusted but even they need replaceing shouldnt be bank busting

Posted on Oct 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loud snapping noise heard when changing gears


From the way you've described it your gear stick linkages maybe on there way out. When changing gear does the car resist getting into gear?

If it's more of a crunching sound then I would try double de clutching, to do this you need to:
change gear as usual but instead of holding down the clutch throughout the gear change hold it down to take the vehicle into neutral then release the clutch then push the clutch down again and change into desired gear.
To change down it's basically the same principal but you push down the clutch to put the vehicle into neutral then push the throttle down just to pitch revs then release the throttle and push the clutch down to change into your desired gear, if it won't go in to gear easily then rather the throttle until it does.

You can go onto youtube and search for double de clutching and I'm sure some results will come up

hope this helps!

Apr 30, 2014 | 2004 Nissan Altima

1 Answer

My 87 ford Turbo Coupe has a difficult time going into 3rd all other gears are fine


sounds like its bulk rings in gear box, they spin the gears ready as u change gear when they wear the gears are not spun enough to select u probably need to over hall gear box , to help u change gear for now double d clutch, whats this as u want to change gear push clutch down move out gear release.. clutch pushdown again put in to gear use this with each gear un need to change what this does is spin gear ready for u as if bulk ring had done it for u if u are good u can just change gear but have to b good for this

Nov 12, 2013 | 1987 Ford Thunderbird

1 Answer

1999 honda prelude manual transmission isn't disengaging all the way when i shift, sometimes locking the shifter in gear or not allowing me to up or down shift. I know my master and slave cylinders need to...


This depends as dose it do it when cold or hot.
2nd when you push in pedal and put in gear dose it go in clean or hard to select 3rd can you hear a grinding noise when pushing in pedal and noise goes
when you take you foot off the clutch pedal IF so then its the thrust bearing on clutch REPLACE ALL .4th if you push in clutch pedal and select a gear and let the clutch out if drive right out (replace)

Sep 27, 2009 | 1999 Honda Prelude

1 Answer

97 civic hard to get in 1st gear/clutch not disengaging


Look for WETNESS at the Master cylinder, and at the Slave cylinder, attached to the Bell housing. The loss of fluid is reducing the Stroke of the Push Rod, which will create Clutch Drag, as you appear to describe.
Regards,DT

Sep 23, 2009 | 1997 Honda Civic

1 Answer

2003 Nissan Sentra SE-R Spec-V clutch sticking and hard shifting


I am dealing with a very similar issue on my 03 Spec V , So far i noticed the clevis pin was loose and the locking hitch pin that slips thru it had fallen out . this caused the gears to not wanna engage due to the bolt behind the clevis which runs to the master cylinder was not getting pressed in when i pushed the clutch pedal in because the clevis pin was slippin on n off giving me no pressure up top .. I had to remove my lower dash panel in order to get visual n hand access to this pin , it is a tight spot to work in as well . May be easist to remove the 4 14mm bolts that hold yur driver seat in to give ya more room to work n stretch out ur arms

Sep 19, 2009 | 2003 Nissan Sentra

1 Answer

2003 Dodge Neon SXT Clutch Problem Less Resistance


check clutch resevoir for brake fluid if none theres a leak if not clutch in need of repair!!! :)

Jul 06, 2009 | 2003 Dodge Neon

1 Answer

Clutch wont engage.


no doubt your clutch has gone again, possibly the slave cylinder.

Mar 19, 2017 | 1999 Suzuki Grand Vitara

Not finding what you are looking for?
2002 Suzuki XL-7 Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...