Question about 2000 Cadillac Escalade

2 Answers

Bled my brakes manually changed pads rotors caliper master cylinder shoes wheel cylinder and I can stand up on my brake pad and it will only come to a slow stop

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 2,428 Answers

WHERE DID YOU START THE BLEEDING PROECESS GENERALY YOU NEED TO START AT BACK PASSERGER WHEEL THEN BACK DRIVER SIDE ITS THE FURTHIST AWAY FROM MASTER CYLINDER AND WHEN YOU DO CALIPERS FRONT THEY HOLD A LOT MORE FLUID THEN REAR CYLINDERSSO START OVER AGAIN AT REAR AND REDO ITS GOING TO TAKE LONGER TO DO FRONT MORE VOLUME MORE SPACE FOR TRAPED AIR

Posted on Oct 15, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 266 Answers

SOUNDS LIKE YOU HAVE A BAD BRAKE BOOSTER CHECK AND MAKE SURE YOU HAVE GOOD VACCUM TO IT WHEN YOU TAKE THE HOSE OFF SHOULD HIS THE BOOSTER IS THE ASSIST FOR THE BRAKES CHECK THAT AND GET BACK TO ME I HAVE ALSO SEEN ABS TROUBLES

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Overheating brakes


I think the problem is the brake pad or caliper, brake pad are too thick or the caliper are not good casted.
First try to confirm if you get a right brake caliper ,then confirm the brake disc ,brake pad, if they all ok, tear down the bracket of caliper, put into brake pad, then put into brake rotor.
http://www.fiverhope.com/category-4-b0-Brake-caliper.html

Jun 27, 2013 | Cars & Trucks

1 Answer

Brake shoes on 1987 f250 460 1987 2 wheel drive how to replace


Lift the front of your Ford F-250 off of the ground using a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench to prepare the truck for servicing. 2 Open the hood on the engine compartment and take the lid off of the master cylinder that bolts to the brake assister on the driver's side firewall.3 Remove the hex-head bolts on the back of the brake caliper with a socket. With the bolts removed, pull the caliper off of the Ford's brake rotor.4 Pull the old brake pads out of the caliper and discard them. Squeeze the brake piston back into the backside brake caliper with pliers, and then insert the new pads into the brake caliper.5 Pull the rotor cap cover off the middle of the rotor with a screwdriver and use a socket to remove the nut located behind the cover.6 Pull the rotor off of the wheel spindle.7 Remove the old wheel bearings from the brake rotor and insert them into the new rotor. If the old wheel bearings are worn, replace them with new bearings.8 Slide the new rotor onto the wheel spindle and secure it using a bolt and socket. After you tighten the bolt, press the cover back onto the rotor.9 Place the caliper on the rotor and secure it with a socket and hex-head bolts. 10 Duplicate the process on the passenger side of the F-250. 11 Close the master cylinder after putting the wheels back on the Ford and lowering it to the ground. Press on the brake pedal to seat the pads against the rotor
Replace the F-250's Rear Brakes 1 lift the rear of the Ford F-250 off the ground with a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench.2 Place a strip of paint on the back of the brake drum and rear brake drum cover so you can position the brake drum orrectly when you put it back on. If you plan to install new brake drums on your Ford F-250, skip this step. 3 Place the brake drum puller on the brake drum and pull the drum from the wheel hub. The method for attaching the brake drum puller depends on the brake drum puller that you use. 4 Remove the springs that attach the brake shoes to the wheel hub by pulling them off with pliers.5 Lift the old brake shoes off of the wheel hub and place the new brake shoes on the wheel hub. Secure the new shoes with the springs.6 Pound the brake drum onto the axle hub with a rubber mallet.7 Duplicate the process on the passenger side of the Ford.8 Put the wheels back on the F-250, lower it to the ground and, then press on the brake pedal to seat the shoes against the brake drum.

Oct 14, 2011 | 1988 Ford F 250

1 Answer

General directions on how to change the front brakes on a Toyota Supra, 1987.


Buy brake pads.
loosen lugs
Jack car, place on jack stand
turn wheel so front of tire is pointing out.
remove tire
remove caliper (two bolts on back side of caliper
slide caliper off rotor.
(if rotor is damaged, see about having it turned or replaced)
take pads off caliper
open hood and remove cap to mater cylinder reservoir
using special tool (or C-clamp and something to protect piston) push the piston back into the caliper fully.
place new brake pads on caliper.
fit caliper on the rotor
Secure caliper to wheel with bolts
replace wheel
remove jack stand
remove jack
tighten lugs on wheel
replace hubcap
start engine (do not drive yet!!!!!)
pump brake pedal until it tightens up
observe reservoir on master cylinder (fill if needed)
replace cap
pump brakes again
take out for a test drive.

good luck and don't forget to vote!!!

Oct 11, 2010 | 1987 Toyota Supra

1 Answer

How do you replace the front and rear brakes in a 2003 pontiac Grand Prix


Removal & Installation Front To Remove:
  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the bottom brake caliper pin bolt.
  5. Pivot the brake caliper body upward and secure out of the way. Do NOT disconnect the hydraulic brake flexible hose from the caliper.
  6. Compress the piston back into the bore using a C-clamp. Figure of brake assembly with caliper raised showing brake pads in mounting bracket gmpc_l4.gif

  7. Remove the inboard and outboard brake pads from the brake caliper bracket.
To Install:
  1. Install the brake pad retainers and both brake pads into the caliper bracket.
  2. Pivot the brake caliper down over the brake pads and into the brake caliper bracket. Insert the lower brake caliper pin bolt and torque bolt to 70 ft-lb. (95 Nm).
  3. Reinstall the tire and wheel assembly.
  4. Lower the vehicle.
  5. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  6. Check the master cylinder level and add fluid as necessary.
Rear To Remove:
Rear disc pads R&I gm-09-00-492.gif

  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the upper caliper mounting bolt.
  5. Pivot the caliper down to access the pads.
  6. Remove the inboard and outboard pads from the caliper bracket.
  7. Remove the brake pad clips from the caliper bracket.
  8. Compress the piston back into the bore using a C-clamp and the old inner pad.
To Install:
  1. Install new brake clips in the caliper bracket.
  2. Install the inboard and outboard pads in the caliper bracket.
  3. Pivot the caliper up over the pads.
  4. Reinstall the upper mounting bolt and tighten to 32 ft. lbs. (44 Nm).
  5. Remove the 2 wheel nuts securing the rotor.
  6. Reinstall the tire and wheel assembly.
  7. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  8. Check the master cylinder level and add fluid as necessary.
prev.gif next.gif

Aug 26, 2010 | 2003 Pontiac Grand Prix

2 Answers

What tools do i need to change front brake pads


need a torque wrench, 3/8" drive 1/2" drive sockets, large screwdriver, screw in front caliper compressor, jack, jack stands, fluid catcher (pale), wrench set, etc.

Hope this helps.

Jul 13, 2010 | 2004 Kia Optima

1 Answer

Brake pad replacement 2004 audi a4 and rotor how do i do and what tools are neccessary?


YOU NEED REMOVE A LITTLE BRAKE FLUID FROM MASTER CYLINDER.THEN YOU RAISE VECHICLE SAFELY.SUPPORT IT WITH JACK STAND.MAKE SURE VECHICLE IS ON LEVEL SOLID GROUND.REMOVE TIRE OR WHEEL.THEN YOU NEED A LARGE C - CLAMP.PLACE C - CLAMP OVER BRAKE CALIPER AND BRAKE SHOE BACKING.TIGHTEN C - CLAMP JUST ENOUGH PUSH CALIPER PISTON BACK IN CYLINDER BORE TO REMOVE CALIPERS FROM ROTORS.TO REMOVE BRAKE CALIPER YOU NEED 2 OPEN AND BOX END WRENCHES ONE TO HOLD CALIPER SLIDE PINS AND THE OTHER WRENCH FOR LOOSEN CALIPER BOLTS.THEN YOU REMOVE CALIPER AND REPLACE FRONT BRAKE SHOES.IF YOU NEED TO REMOVE BRAKE ROTORS JUST REMOVE THE BRAKE CALIPER CARRIER SUPPORT BOLTS THE REMOVE THE BRAKE CALIPER CARRIER SUPPORT THEN REMOVE ROTOR.YOU NEED TO REPLACE BOLTS WITH NEWS AND USE LOCK TIGHT.THEN YOU PUT IN NEW BRAKE PADS IN CALIPER PUT CALIPER BACK ON SUPPORT CARRIER.REPLACE WITH NEW BOLTS USE LOCK TIGHT THEN TORQUE BOLTS TO 26 FT LBS.MAKE SURE MASTER CYLINDER COVER IN PLACE.WHEN YOU FINISH REPLACING BOTH FRONT BRAKE PADS PUMP BRAKE PEDAL TO SEAT BRAKE SHOES AGAINST BRAKE ROTORS SO YOU WILL HAVE FIRM BRAKES WHEN YOU APPLY THEM. THEN CHECK YOUR BRAKE FLUID LEVEL IN MASTER CYLINDER MAKE SURE ITS NOT LOW. MAKE SURE YOU HAVE FIRM BRAKES BEFORE DRIVING.IF YOU HAVE ANY PROBLEMS CHANGING FRONT BRAKE PADS YOU CAN GO TO ANY AUTO PARTS STORE AND BUY A HAYNES REPAIR MANUAL.

Jun 16, 2010 | 2004 Audi A4

1 Answer

How i do change the brake pads front?


How to Replace Brake Pads
(DIY Complexity: Moderate - Time: 2.8 hours)

Parts:
1. Brake Pad Set

Tools:
1. C-Clamp
2. Flat Head Screwdriver
3. Jack Stand Set
4. 3/8 in. Drive Ratchet
5. Combination Wrench Set
6. Tire Iron
7. Socket Set
8. 1/4 in. Drive Torque Wrench
9. Dial Indicator

Supplies:
1. Brake Cleaner
2. Brake Lubricant

Steps:
Step 1 Secure your vehicle on a level surface, making sure your car will not roll or lean too much when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Remove the cap from the brake master cylinder. Using a turkey baster, remove a quarter of the brake fluid from the master cylinder. Lift up the front of your vehicle using a floor jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds and the frame are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 4 Remove the front wheels by removing the lugs nuts that are holding them on. To do this you will need to find the correct size socket and large ratchet or tire iron and turn them counter clockwise. If your vehicle is equipped with hub caps (plastic covers over the wheels), these will need to be removed to access the lug nuts.
o Tip: It is a good idea to try and break the lug nuts free before you jack the wheels off the ground. This way they you will not spin the front wheels or put stress on the transaxle.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 5 Inspect the brake rotors for scoring, grooves, cracks and discoloration.

Step 6 Remove the brake caliper mounting bolts.

Step 7 Slide the brake caliper off of the brake rotor.
o Tip: If the brake rotors are worn and there is a big lip preventing the brake caliper from sliding off easily, gently pry one pad back into the brake caliper to clear the lip and make removal easier.

Step 8 Support the brake caliper up and away from the working area. Make sure you do not kink or pinch any brake lines. Do not disconnect the brake line.
o Tip: Use a bungee cord to secure the brake caliper out of the way and hang it on the suspension spring.

Step 9 Remove the brake pads from brake caliper.

Step 10 Compress caliper piston using a C-clamp.

Step 11 Install the new brake pads in the brake caliper.

Step 12 Reinstall the brake caliper.

Step 13 Torque the brake caliper mounting bolts to manufacturer’s specifications. Repeat for other side.

Step 14 Install wheels and torque to manufacturer’s specifications.

Step 15 Refill the brake fluid in the brake master cylinder and reinstall the cap.

Step 16 Road test vehicle, break in new pads.
o Tip: To break in pads and rotors refer to manufacturers recommendations. Some companies have different procedures for pad and rotor break in.


Hope this helped (remember comment and rated this).

Apr 09, 2010 | 2002 Nissan Altima

2 Answers

Spongy brake pedal even after ABS bleed and base brake bleed.


Did you adjust the rear shoes out? If the rear drum brakes are out of adjustment they will give you a lot of pedal travel. If the pads are worn have no fear of that U-CLIP brake spring, just change one shoe at a time. Take the spring off one side, change the shoe, put the spring back on the post and do the same to the other shoe, no problem.

Dec 03, 2009 | 2001 Chevrolet Venture

1 Answer

Pistons in both front calipers stay out, both calipers replaced


You may have a leak in the booster or master cylinder. You can put a pressure tester on the system to test for leaks. It does sound like you have an air leak.
You can try to bleed the master cylinder, then slave cylinder, then brake lines.

Aug 24, 2009 | 1993 Oldsmobile Achieva

Not finding what you are looking for?
2000 Cadillac Escalade Logo

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...