Question about 2003 Nissan Xterra

Open Question

Lights don't flash and horn doesn't sound with remote entry?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

hiseyj
  • 99 Answers

SOURCE: HORN WILL NOT SOUND BUT DOORS WILL LOCK WHEN I USE MY KEYLESS ENT

The title of you problem mentions the horn but the actual problem mentions the flashers? Which is it? You can turn the 'horn beep' feature on and off by simultaneously holding the lock and unlock buttons down on the remote for about 3 seconds or more. When the horn feature is turned on you will hear the horn, and when it turns off you will only see the lights flash.

Posted on Nov 30, 2008

FoRdMaStEr
  • 51 Answers

SOURCE: remote keyeless entry

a common issue i see alot in the WJ grand cherokee body style is that the wires between the door and body break and cause all kinds of issues like this. usually its on the drivers side in that black rubber wire loom

Posted on Jan 10, 2009

juggernautxt
  • 145 Answers

SOURCE: Flash lights on locking doors with control

he is pushing the button a second time which is unnecessary.
it will cause damage to the lock actuators. yours will do it if you push the lock button a second time, but i do not recommend as stated above.

Posted on May 15, 2009

Remontti-J
  • 32 Answers

SOURCE: Remote entry system is not working along with headlights/tailligh

Check Fuse 10 in the "Power distribution center". It is conntected to Fuse Block to Fuses 1,2 and 3. Fuse 1 and 2 is connected to Head lights switch. Fuse 3 is for Remote keyless entry module. This circuit is something happend. Here are the photos of fuses: http://www.ptcruiser.fi/ptgalleria/albums/userpics/Power_distripution_center.jpg http://www.ptcruiser.fi/ptgalleria/albums/userpics/fuse_block.jpg

Posted on Jun 12, 2009

  • 4088 Answers

SOURCE: location of a 2003 dodge stratus horn, also not loud enough

Horns are usually in front of the radiator and behind the grill--look for two of them, one on each side. Make sure they both sound. If only one works, there is a significant reduction in sound level. There may be road debris stuffed into the horn's throats--poke a hooked stiff wire into the throats and see if anything comes out. Most are sealed and can't be taken apart to clean--replacement is about the only recourse. (look in a wrecking yard for replacements)

Posted on Nov 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a problem with the electric lock security system. Under normal conditions if I press the unlock on the key remote, the lights will flash once and the doors unlock. When I press the lock button


if this is a factory lock security system you can contact dealer for instruction sheet to re-program your remote or have them do that for you if vehicle is under warranty. if not you can go online and find the procedure for your make,model and year of vehicle. sounds like the remote's battery is need of replacing or the remote needs to be re-programmed

Feb 03, 2015 | 2008 Nissan Rogue

1 Answer

The alarm system has activated and we cannot disarm the system via the Remote Key Fob or by key at the doors or hatchback. Tried disconnecting battery same problem. When the doors open the system...


Hi Edward:
In dashboard, your THEFT warning light is blinking? If the answer is yes, your antotheft system is activated and will need restart and resynchonized. This occurs when battery is disconneting or other un-authorized key is used.

Vehicles equipped with Vehicle Theft Security System (VTSS) are protected from vehicle theft andunauthorized entry. VTSS system monitors vehicle doors, hood, liftgate and ignition. If an attempt is made toenter or operate vehicle without proper disarming of system, vehicle horn will sound, headlights, taillights andparking lights will flash, and engine will be prevented from running.

VTSS system arms when ignition is off, vehicle is exited, door is locked using power door locks and door isclosed. Alternatively a remote keyless entry transmitter can be used to arm system. A security light on panelwill flash for 15 seconds to indicate system is arming. At the end of 15 seconds, if no door, hood or tailgate isopened, system is armed.

If alarm is triggered, horn will sound for 3 minutes, and lights will flash for an additional 15 minutes. If hornsounds 3 times when either front door is unlocked, vehicle has been tampered with (tamper alert). If doors arelocked manually or with key, system will not arm (manual override). If an unauthorized entry does occur, VTSSsystem signals Powertrain Control Module (PCM) to prevent vehicle from being driven. PCM reduces injectorpulse width to zero, causing a start and stall condition.

System can be disarmed with the keyless entry transmitter, or by using key to enter vehicle. In both instances, if alarm was activated, vehicle alarm will be terminated. If battery is disconnected and reconnected, alarm will beactivated and it will be necessary to disarm system as indicated.

Please, send us some email account to send you this procedure in PDF format file.

Feb 08, 2012 | 1996 Jeep Grand Cherokee

1 Answer

I got the Viper 5101 remote start installed in my 2007 Hyundai Sante Fe at best buy. The remote works for auto start, but will only lock and unlock the doors sometimes. It seems like if I unlock or lock...


I would take it back and tell them they need to fix it. it sounds like a wire for the lock/unlock may of fallen off or there is a problem with the remote stare module. wires tend to fall off if all the used were crimp connectors and didn't solder the wires together.

Jun 01, 2017 | Hyundai Santa Fe Cars & Trucks

1 Answer

After the battery was replaced on the car, the key less entry does not work correctly, when you lock it, the lights do NOT flash and the horn does NOT beep, when you unlock it the lights DO flash but the...


You might need to take it in to a dealer to have the fob synched to the car. Is this in Canada , USA or some other country? Some counties have an immobilizer that can become confused if they lose power completley ... like from changing the battery.

May 05, 2011 | 2006 Kia Spectra

1 Answer

I have a 2000 pontiac trans am. when i set my alarm my haedlight pop up. they never use to. replaced module,and headlight motors,still didn't fix it.


In your owners manual on pages 2-19 and 2-21 tells you how to change this.

Entering Programming Mode
1. Turn the ignition key to RUN, then to OFF. This will
disarm the content theft-deterrent/alarm system
(if equipped).
2. Remove the RADIO fuse. This fuse is located in the
main fuse block which is located on the left side of
your instrument panel. The radio fuse is on the lower
right-hand corner of your instrument panel. See
"Fuses and Circuit Breakers" in the Index.
3. Turn the ignition key from OFF to RUN three times
quickly (within five seconds). The vehicle will
respond by locking the doors, unlocking the driver's
door and releasing the hatch. Your transmitter is now
ready to match the vehicle. Leave the ignition
in RUN.
4. Press and hold the LOCK and UNLOCK buttons on
the first transmitter for 15 seconds. The vehicle will
respond as in Step 3.
5. Repeat Step 4 for the remaining transmitters.
6. When you have finished matching all of your
transmitters, replace the RADIO fuse.
7. Check that all transmitters work by pressing
the buttons.

Programmable Modes
Your vehicle can be programmed to one of the
following modes:
Mode 1: All Off (The headlamps will not flash and the
horn will not sound to provide you feedback that a
lock/unlock command has been received by the remote
keyless entry transmitter.)
Mode 2: Horn and Lamps/Lamps (Your horn will sound
briefly and your parking lamps will flash when you
press LOCK on the remote keyless entry transmitter.
Only your parking lamps will flash when you press
UNLOCK.)
Mode 3: Horn and Lamps (Your horn will sound briefly
and your parking lamps will flash every time you push
LOCK or UNLOCK.)
Mode 4: Lamps (Your parking lamps will flash every
time you press LOCK or UNLOCK.)
Mode 5: Lamps/Horn and Lamps/Lamps (Your lamps
will flash upon the first press on LOCK, your lamps will
flash and your horn will sound upon the second press
on LOCK and your lamps will flash upon any press
on UNLOCK.)
Vehicles are delivered programmed in Mode 5.
To change the mode, do the following:
1. Press the UNLOCK button on the remote keyless
entry transmitter.
2. Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
3. Press the UNLOCK button, again, on the remote
keyless entry transmitter until you hear the number
of chimes that correspond to the mode selection
you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

When programming is complete, turn the ignition to
OFF and reinstall the RADIO fuse.

Sep 20, 2010 | 2000 Pontiac Firebird

2 Answers

Remote entry system is not working along with headlights/tailligh


Check Fuse 10 in the "Power distribution center". It is conntected to Fuse Block to Fuses 1,2 and 3. Fuse 1 and 2 is connected to Head lights switch. Fuse 3 is for Remote keyless entry module. This circuit is something happend. Here are the photos of fuses: http://www.ptcruiser.fi/ptgalleria/albums/userpics/Power_distripution_center.jpg http://www.ptcruiser.fi/ptgalleria/albums/userpics/fuse_block.jpg

Jun 05, 2009 | 2002 Chrysler PT Cruiser

1 Answer

Keyless entry not working


Try re-programming the remotes, here is the procedure for your car.
JAGUAR
XJ8 Remote Control Programming
1. Unlock the trunk with key.
2. Turn Ignition on.
3. Warning light on dash comes on.
4. When they go out, lift arm rest, inside their is a valley button, Press 5 times within 5 secs of lights on dash going out, Horn & Lights Flash.
5. Press any button on remote, remote programmed

Dec 11, 2008 | 2006 Jaguar XJ8

1 Answer

HORN WILL NOT SOUND BUT DOORS WILL LOCK WHEN I USE MY KEYLESS ENT


The title of you problem mentions the horn but the actual problem mentions the flashers? Which is it? You can turn the 'horn beep' feature on and off by simultaneously holding the lock and unlock buttons down on the remote for about 3 seconds or more. When the horn feature is turned on you will hear the horn, and when it turns off you will only see the lights flash.

Nov 12, 2008 | 2005 Nissan Xterra

2 Answers

Chevrolet HHR horn and lights flash every few minuets.


Its not better to go to a key copying and re-set your remote entry?

Jul 03, 2008 | 2006 Chevrolet HHR

Not finding what you are looking for?
2003 Nissan Xterra Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...