Question about 2008 Dodge Nitro

1 Answer

Replacing glass and regulator on 2008 nitro cant find how to releace window track to install new glass what trick am i missing??????

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

There should be screws on the bottom of the track on both ends mid way, once loosen glass will slide up and out. hope this helped tim

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the window on the driver side of a 2008 Dodge Nitro to get to the door lock rods


Most windows are attached to the window regulator assembly using two bolts. Roll the window up/down until you can visually see them. They have a head size of 10mm. Remove the bolts and the window will seperate from the regulator and remove the glass from the door channel.

Jun 21, 2015 | Dodge Cars & Trucks

1 Answer

How do i install side glass?


the glass has bolts holes in it that has bole in it take the class out when it is half the way down

May 04, 2017 | 2000 Saturn L-Series

1 Answer

How do i replace the glass of the driver door window of a 1999 mercury sable


The regulator runs a track.. a strip of alluminum up and down,which the window(galss) itself rides on...There is either bolts or rivits in the metal ststrip....remove them and clean all the glass out of track and install new glass in track bolt it in and re-install the plastics and door skin or anything else you might have removed....BE CAREFULL THOUGH AS PUTTING YOUR HAND IN AND OUT OF THE CUTOUTS OF DOOR CAN LEAVE YOU WITH QUITE A FEW CUS AND SCRAPES......

Jul 18, 2012 | Mercury Sable Cars & Trucks

1 Answer

Driver side window ***** and gets stuck when going up


1st try this get a can of Silicone spray lubricant, cover any exposed surfaces and carefully spray lube (shake can before spraying) into the window felt tracks in the front and rear of the glass until it runs out the bottom of the door, run the window up and down a number of times to distribute the lube. This should ease the effort required to roll the window up, if it doesn't cure the problem you will need to replace all the glass guides.

Jan 20, 2012 | 2003 Pontiac Montana

1 Answer

My drivers side rear window is off the track and i believe the cable is broken because i cant re-latch it to where it goes. how do i fix this?


WINDOW GLASS REGULATOR BROKEN OR GLASS TO CHANNEL NUTS LOOSE AND MISSING.YOU HAVE TO REMOVE DOOR PANEL FIX WINDOW GLASS.

May 31, 2011 | 1999 Oldsmobile Alero

1 Answer

How to repair front driver side widow motor.at fir st there was a grinding sound that made me think it was off track. now its not doing anything. motor works all the way up and down but glass doesnt move.


{: ) Sounds like you have a faulty window regulator. Usually the regulator cable gets broken or detached. If this is the case, your window may not move at all, even though the motor seems to be working when you switch the button up or down.
The door trim panel need to be removed totally. Once removed, you will find two bolts for the glass catch, 3 bolts for the motor, and 4 bolts for the regulator.( all #10mm )
Begin by loosening the 2 bolts on the rubber insulated glass catch, just enough to pull the glass up from its track. You may need an assistant. You need to lift the glass (only) to the top closed position, and apply a strong masking tape to hold the glass on that position for the time being.
Continue by removing the motor and regulator bolts. I hope the replacement part is readily available. I think the window regulator comes in assembly, the motor is integrated to the regulator.
When bolts removed, simply pull out and fold to remove outwards. Be sure you remember how it was mounted before you removed it.
Installation is just the reversal procedure. Position first the regulator assembly and semi-tight all the bolts. Its better if you just follow the old bolt markings. Secure motor connection.
Loosen the two bolts on the glass catch, just enough for the glass to slide and seat freely. Temporarily connect the window switch. Press the up button slowly and align the glass with the catch. When glass seated fully, tighten the 2 bolts on the catch to hold it firmly. You can remove now all the tapes you sticked.
Try to operate the window up and down carefully and observe. Make that final tightening of the regulator with the glass resting in the the full up position. Re-install the trim panel. Goodluck.

Nov 17, 2010 | 2008 Chevrolet Suburban

1 Answer

Trying to replace a power window motor on an 03 maxima but can't get motor assembly out from behind door and now window is off track as well. Need to know how to get window back in track. Do I need to...


The window need to be lowered to get to bolts that hold it to regulator,then pull glass all the way up and wedge it there,next is to remove all the bolts securing the regulator to door,now work regulator out and replace the motor, with regulator out remove the wedge tilt glass until you are able to get it on the front and rear track ,on track now pull window back up and wedge it.install regulator and bolt it up to door,move regulator with switch to line up bolts to attach glass, now lower glass onto regulator arms and tighten, hope this helps.

Sep 12, 2010 | 2004 Nissan Maxima

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Window is off track slides down


Go to you dealer and purchase a window regulator for the side that is bad remove door panel, lock and handle remove old regulator and install new one be careful not to drop the balancing pin or remove it from the glass (very important) look at how it is assembled if pin is not in glass replace the glass the pin is made not to be removed from glass if it has been you will forever have problems until you replace the glass from dealer with pin installed

Mar 31, 2009 | 2003 Jeep Liberty

3 Answers

Hey when i push the power botton for the rear window it doesn't go down,I checked the power button,and its good ! Can i replace the power motor in the rear window,and where is it located,i would like to...


  1. Raise and support the rear door window glass to the full up position.
  2. Remove the interior door handle.
  3. Remove the rear door speaker.
  4. Remove the water shield.
  5. Disconnect the rear door window regulator motor electrical connector.
  6. Remove the rear door window regulator rivets.
  7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
  8. Installation is the reverse of the removal procedure, noting the following:
    • Cycle the door glass to make sure of engagement of the drive mechanism.
    • Remove the rear door window glass-to-regulator bolt or rivet.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
    • Secure the rear door window glass in the full UP position with tape.
    • Disconnect the window regulator motor electrical connector.
    • Remove the 2 window regulator nuts.
    • Remove the 3 window regulator motor bracket nuts.
    • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
    • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Connect the window regulator motor electrical connector.
    • Remove the tape securing the rear door window glass in the full UP position.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
    • Install the window regulator motor
    • Remove the window regulator assembly.
Remove the window regulator motor

Feb 23, 2009 | 2001 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...