Question about 2005 Ford Focus

1 Answer

Cannot depress clutch pedal - 2005 Ford Focus

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

Check fluid level in clutch reservoir & check under dash for obstruction

Posted on Oct 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you get to Chevy s 10 1998 clutch pedal upper pin and bushing


CLUTCH PEDAL REPLACEMENT (CLUTCH) Document ID# 46043 Clutch Pedal Replacement

Removal Procedure



  1. Remove the master cylinder rod from the clutch pedal.


  2. Remove the clutch pedal from the support by depressing the side tabs.

Installation Procedure



  1. Position the clutch pedal into the support.


  2. Secure the master cylinder rod to the clutch pedal.

Good Luck

Aug 11, 2016 | Cars & Trucks

1 Answer

High pitched squeal when jeep idles or during deceleration. soonafter, clutch pedal jumped violently under my foot followed by engine stalling out. could not depress clutch pedal after that.


It sounds like your clutch bearing has gone they are usually on a pendulum system it screeches before it starts to go. Best get it checked.

Apr 15, 2014 | 1995 Jeep Wrangler

1 Answer

Engine revs but no acceleration


Clutch plate and pressure plate seem to be too weak to pull the car. Or one of the CV joints is detached from the gear box. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

1 Answer

Car will not accelerate when gas pushed


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

2 Answers

My clutch won't engage 1997 Honda civic


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

Apr 06, 2013 | 1997 Honda Civic

1 Answer

Try different location on the clutch pedal to get it to start


If you look above the clutch pedal you should be able to see the operating switch, depress clutch pedal and see that there is clearane between the pedal and switch, It may be loose or require adjustment, the other option is to remove terminal block and bridge the terminals, this will delete the need for the switch and also the need to depress the pedal to start the motor, Regards Mike

Oct 20, 2012 | 2006 Mitsubishi Outlander

1 Answer

Depress clutch turn key dash lights up. No click no nothing


you may have a bad clutch switch which will only allow the car to start with the clutch pedal depressed.it allows power through the switch only with it depressed to start the car so you won`t start the car with it in gear causing an accident.there will be a switch that the clutch pedal pushes against that allows power to flow through it to start the car.there should be power on one side with the key turned on and power on the other side with the clutch depressed.

May 25, 2011 | 1993 Geo Tracker

1 Answer

Gear box problem car want start unless wiggle gear stick i fink sensor whats the problem


There is a Clutch Start Switch that allows the battery voltage to be supplied to the starter when the the clutch pedal is depressed.

When the clutch pedal is depressed, there should be continuity on terminal numbers 1 and 2.

The switch is located in front of the clutch pedal stem.

Feb 27, 2011 | Isuzu Trooper Cars & Trucks

2 Answers

My '98 Escort ZX2 has 175,000 miles. I recently noticed a grinding or chattering with the clutch pedal depressed with the transmission in first gear. While stopped at a light the car suddenly began jumping...


Hi:
You need to check your clutch master cylinder reservour, not your brake cylinder. It is located approx in front of the clutch pedal, outboard of the brake cylinder. If it is low, you need to inspect for leaks around it, the lines connecting it to the clutch slave cylinder that is mounted on the transmission.

Dec 05, 2009 | Ford Escort Cars & Trucks

Not finding what you are looking for?
2005 Ford Focus Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...