Question about 2006 Pontiac G6

1 Answer

Alright so say i have put 8 1/2 things of remission fluid and it has still not over flowed could that be bad??? and what do you have to do

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 2,100 Answers

You put 8 1/2 qts of tranny fluid in there and What??? Where did you put it?? Do you have a dipstick?? Or filler plug on the side of the tranny? A filter change only requires 5 qts at the most, that is taking the pan down. A total rebuild requires 13. I don't know what you did, but something is wrong. You didn't dump it in the oil did you? Check it out. I'm dieing to find out.

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1.6 ford focus zetec is taking too long to start either cold oo warm. (2007)


Any number of thing's could cause this condition , Weak fuel pump , low fuel volume , an engine sensor , mass air flow for one , A crank sensor that is going bad , cam sensor etc... your best bet would be to have it diagnosed professionally , rather then guessing an just replacing parts

Jul 13, 2016 | 2007 Ford Focus 1.6

1 Answer

Awd disabled 2005 buick rendesvous


It is the AWD rear flow valve, on the rear differential that is bad, not the ABS! This is how to replace it after buying a new one. Put drain pan under rear differential, unhook connector, unscrew flow valve bolt and pull it out. Reverse order to install. You will need to refill with 4 pints of versatrak fluid (unscrew fill plug) because when you remove the flow valve, all the versatrak fluid comes out. You can only get versatrak fluid at any GM dealership. Do not reuse old nasty versatrak fluid because that is why it got plugged up in the first place. (ASEGM)

2d0be49d-bb62-4173-861e-b1352e31eb5f.jpg

Oct 17, 2014 | 2005 Buick Rendezvous

1 Answer

I have a 1995 sl320 on occation my reverse is delayed for a few seconds and when in reverse backing up a hill it wants to shutter I then stop put in park and then reverse will be alright ,,any idea?


Stage pistons may be going bad. They can be replaced in car depending. If replacing fluid and stage pistons don't help then full rebuild is required.

Oct 25, 2013 | Mercedes-Benz S-Class Cars & Trucks

1 Answer

I tried to bleed the brakes rf good lf no fluid comes out.replaced rf line working good,pulled line from master cyl. and pulled bleeder valve no fluid. i have a 99 cavilier with abs,any idea.i havent tried...


Im confused first thing is to connect all lines, fill master and start bleeding at master, have someone pump brake three times and hold, open line at master allow fluid or air to flow and close, do not leave open to long,after 3 sec of fluid flow close line. you will do this to every line on the master. pumping the pedal three times and holding down pedal every time you open the line , after bleeding master you will then go to the left front as this is the brake with no fluid flow. you will make sure brake fluid is full always check after a few bleedings.

Remove the bleeder screw and place finger over the hole. tell them when to go down and when to let up, this may take a while if a lot of air is in system, remove finger and tell them to push down then put finger over hole and tell to release then tell them to push as they push release finger, you will need to do this until you get fluid flow making sure when pedal is released that hole is covered with finger so that air is not sucked into system. once you get a flow you will put bleeder in and bleed that wheel, if bleeding is good you will then bleed system starting at rt rear then left rear and then rt front and last left front.

Dec 25, 2012 | Cars & Trucks

1 Answer

Why would a 98 grand prix gtp transmission pull just fine for 5 milesthen quit cut off car put in nueatral 5 r 10 secs grank back put in gear pulls like a new 1 same thing over and over please explain


There are many things that can cause this, a bad transmission pump or torque converter, restarting the engine helps it because you are stopping the flow of oil and then restarting it oil starts to flow again and increase pressure as you accelerate ,
Another problem could be in the vanes of the torque converter with the same concept when you shut it down and restart it.

You would need a ****** shop to check pressure and put scan tool on it to watch readings, and last it may be low on fluid or internal leakage causing loss of pressure.

Sep 30, 2012 | Cars & Trucks

2 Answers

Nkr 200 1991 brake alarm sounds low brake pressure


are you loosing brake fluid? do you notice any leaks? it could be a bad master cylinder or a bad proportioning valve, master cylinder is more common failure.

Jun 09, 2012 | Cars & Trucks

1 Answer

I have a 2001 toyota celica. i put a new power steering pump on it because the old one was moaning and of course the car was difficult to turn. but.. the new is doing the same thing and blowing the fliud...


Sound like the steering rack is bad.The moaning could be the pump working to hard which could cause the fluid to overheat and over flow.Does it over flow when you first start it and it is cold

Nov 27, 2008 | 2001 Toyota Celica

1 Answer

Trouble with engine


check the transmission fluid level. is it full? is it dark red or black? is it burn't or sharp smelling? you may have a burned up transmission if the fluid is full and it won't move. can you feel the gears being changed like a ratcheting of the shifter handle when moved from park to the desired gear? if not then you have some linkage problems and that can be repaired alot cheaper than a transmission. Good luck .... Scott

Sep 08, 2008 | 1995 Lincoln Town Car

1 Answer

Over Heating


Hi! The problem is you have air in the system . I see this all the time with these cars . OK what you need to do is put your therm. back in. First let me tell you there are two ways to fix this #1 on the therm houseing you have a little bolt that can be losend just a little, You will see fluid start to come out or a lot of steem when this happens tighten back up and problem solved. Make sure you have the over flow cap on when runing the car so that presure pushes the fluid up the hose.The other way to solve this is to take the hose off the therm houseing and fill it with fluid to the top with over flow cap on and put it back on with spilling little fluid. Start the car after eather way and I think you will be jumping for joy! I see pro machanics over look this 8 out of ten times. The problem is since you cant get to the rad to fill it gravity wont let the fluid get to the block. One more thing if the person that fixed the car say thay did that already try it again for argument sake. Hope this helps let me know how it went.

Jul 14, 2008 | 1997 Chrysler Concorde

Not finding what you are looking for?
2006 Pontiac G6 Logo

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...