Question about 1998 Lincoln Town Car

1 Answer

How to bleed brakes for a 98 lincon town car with abs

Posted by on

Ad

1 Answer

Same as you always have, with any vehicle,engine running,ABS no issue

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Chevy blazer, lost most of brake peddle and


No reset on 98"s bleed all the lines. Replace all the lines in my opinion...That's what I do. we are talking almost 15 years of rust and fatigue...

Sep 24, 2014 | 1998 Chevrolet Blazer

1 Answer

Abs bleeding


Open the bleed port on each wheel Brake fluid starts to drip when one drop falls all the air is out. (one wheel at a time)

Feb 09, 2014 | 2003 Chrysler Town & Country

1 Answer

Replaced a rear brake line on my 98 bonneville w/abs. how do i bleed system


Same as we all have for 70 years
Nothing special because of the abs
RR,LR,RF,LF
Need a helper as always, to press the brake
pedal motor running.

Aug 11, 2013 | Pontiac Bonneville Cars & Trucks

1 Answer

Master cylinder replaced and still no brakes


Did you bleed the master cyclinder before installing it?

Aug 30, 2012 | 1998 Chrysler Town & Country

1 Answer

98 ford windstar brake pedal falls to floor master cyl replace bleed sytem with scan tool


your whole abs system dropped and you have to start with each wheel and bleed them so you can get you full abs system back up and have full pedal

Feb 04, 2010 | 1998 Ford Windstar

1 Answer

Brake pedal being soft on 02 town and country


Add brake fluid and bleed the air out of the brake lines.

Jun 06, 2009 | 2002 Chrysler Town & Country

2 Answers

Bleeding brakes on 98 yukon


Open the bleeders on the calipers in this order and let gravity bleed. Front pass & Driver rear then front driver & pass rear. ABS could be damaged if fluid is forced in to ABS Manifold when depressing piston in caliper. The correct way is to clamp brake line open bleeder then depress the piston. The key word here is COULD,

Mar 18, 2009 | 1998 GMC Yukon

1 Answer

Brakes fade when coming to a final stop 1998 Chevrolet silverado


this is the coming problem with '98 chevy trucks. abs system failure. you might need to replace complete abs unit and properly bleed your brakes. before you replace abs control unit you should pull the abs codes.

Mar 14, 2009 | 1998 Chevrolet K2500

1 Answer

98' Ford Windstar has a spongy brake


Have you had anyone try to clean and adjust the rear brakes? You will need a shop to scan the van for ABS codes first to cure the ABS light.

Mar 02, 2009 | 1996 Ford Windstar

Not finding what you are looking for?

Open Questions:

0 Answers

98 Lincoln TC,Cold starts fine ,runs good until warm, then shuts off. No codes,Cranks ok, have spark, PATS ok. No fuel pressure, cant hear fuel pump prime,New Fuel relay. jumped fuel pump - works. I do not hear fuel pump prime up, do not have fuel gauge, but pressing on valve in fuel rail- no pressurized fuel. Fuel regulator seems ok, not leaking / vacuum line dry as a bone. If I let it set for 15 min , it will start up again, but for a few minutes then dies out. If I let it set overnight it starts up perfectly and runs until operating temp is reached then stalls/stumbles, and shuts down. Vacuum is good while cranking, even with no start, Checked Inertia switch in trunk, it is not tripped. I have seen Ford TSB summaries' that mention issues like this , but I am not able to see to description. A point to add, the MAF sensor was cleaned, then I decided to replace it and did not make a difference. I do not have any stored codes, and the PATS is working fine, typical 2 second flash from and once key is inserted a 3 second steady light, then disappears. I have seen the TSB mentioning C103 Connector, it looks fine, I swapped out fuel pump relay with ac relay, still no difference.mention of wires around battery, do not know where to start. in dash service engine light and odometer is normal, seen other posts the say they only have lines, but mine is ok. the start of all of this , I washed engine with regular garden hose, ( not using pressure washer).also in the mean time, rear window defroster stopped working as well, can not say for same reason, but a mention.My problem started after washing engine. this is one of four Panther platform vehicles I owned with exact 4.6l w code engine, which I rinced down before. The only sensor I can think of is Oil pressure , or a corroded wire

Feb 27, 2017 | 1998 Lincoln Town Car

See all 1998 Lincoln Town Car Questions

1998 Lincoln Town Car Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...