Question about 1993 Chevrolet S-10 Blazer

1 Answer

Need to change the fuel pump can i cut a hole in the floor, if so where

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 127 Answers

Hi, you will have to drop the tank to change it,I would not suggest cutting hole in floor,you might cut wires or even worse fuel lines ( ca-boom ) the tank is not to hard to drop.( should just be 2 straps holding tank up. good luck. yz-maniac

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to drop fuel tank on 1988 surburban


Drain the gas tank. I didn't have a lift so I used a floor jack under neath the gas tank. I used a piece of plywood on top of floor jack that would fit between tank straps. Take the fill tube loose, take fuel lines and electrical connectors loose. Take tank straps loose,you may have to drop tank a little to reach some connections. If I remember correctly the fuel pump is in the middle of tank. I don't know if you would want to cut hole in floor of surburban to reach pump? I don't have any info about cutting that hole, if you try that, that is your responsibility.

Dec 11, 2016 | 1988 Chevrolet Suburban

1 Answer

I have a 1995 dodge neon need to make an access panel for fuel pump where do I need to cut , have no ability to drop the tank


go to the junkyard and look at a fuel tank for a neon and you'll know. or cut a large hole in trunk floor

Mar 28, 2015 | 1995 Dodge Neon

1 Answer

Can I cut an access hole in floor above fuel tank to remove fuel pump on a 2001 Pontiac Grand Am instead of dropping fuel tank and if so, where would I cut out access hole location?


You would have to figure out a way to cut the floor without cutting the tank. The gap is less than one inch. And the fuel lines come out with the sending unit. They have to be disconnected a few inches away from the sending unit.

Dec 19, 2012 | Cars & Trucks

1 Answer

Do you have to drop the fuel tank to change the fuel pump?


IN most veihicles the fuel pump is on top of the fuel tank so yes you have to drop the tank. I have seen my friend cut hole in the floor board and tank the fuel pump out that way but im sure you dont want to do it that way.

Dec 20, 2010 | 2003 Pontiac Aztek

2 Answers

Fuel pump access


fuel tank will need to be dropped down to gain access

Mar 04, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Why not cut a hole in the floor above the gas tank and remove the fuel pump that way. Probably a dumb question, but I need the ask. Thanks


some have a trap door in floor board to get to fuel pump, check it out.
need to take tank out to cut hole anyway :(

Sep 08, 2009 | 1994 Plymouth Grand Voyager

2 Answers

What is the best way to access the fuel pump to repalce it without adding expenses? They want to cut the floor and do it. Will this cause problems in the winter? We live in Michigan with a lot of deep...


Too bad GM doesnt provide a cover to access tank without dropping the tank. I would think creating this "hole" would be quite the endeavor and done correctly would add quite the additional time and expense. Decline cutting holes and drop the tank in order to service the pump/sender. Any reputable repair firm should or would never recomend this measure in order to access the pump in the fuel tank I would hope....

Jul 10, 2009 | 1997 GMC Jimmy

1 Answer

Can I cut a hole thru the trunk to access fuel pump?


If you can do it without damaging anything. it is all up to you. I would make sure to seal it back tight after cutting the hole. Don't use anything bit a chisel. I have never seen it done but it's your car.

Feb 16, 2009 | 1994 Buick Park Avenue

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

418 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...