Question about Chrysler Concorde

1 Answer

How do I take off harmonic balencer have all the tools just don't know where they go

Posted by on


1 Answer

You should have cone that goes on the puller screw to remove ,and a threaded adapter to pull new one on.

Posted on Oct 14, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1997 f-250 7.5l harmonic balancer removal how do you remove it

no set bolt you will need a harmonic balancer puller some truck take a special puller

Jan 05, 2016 | Cars & Trucks

1 Answer

5.7 tbi replaced cam, lifters, timing chane now won't start

check the crank position sensor and cam position and wires are connected
reset the ECM using a scan tool that has the protocols for GM

Jul 09, 2017 | Cars & Trucks

1 Answer

How would i time my 1992 ford mustang without a harmonic balencer pulley

if this a 2.3 set the key on the crank at the very top, this will get you real close to TDC.

May 23, 2012 | 1992 Ford Mustang 2.3

1 Answer

What would cause my harmonic balance to be off balance?

The harmonic balencer is to pieces of metal ,pressed together with a rubber insert in between. The ruber can be damaged after long exposure to oil .Let me know if that helps

Mar 27, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

Oil leak up by harmonic balencer on 4.3 chevy s-10

front of oil pan maybe or chain cover as well

Nov 24, 2009 | 2000 Chevrolet S-10

1 Answer

Crank shaft harmonic balencer bolt

THe Harmonic balanced bolt is loosened by turning it counter clockwise. It is recommended that you get the special tool to hold the harmonic pulley stationary while the bolt is loosened or tightened. However the bolt can be loosened if you use an impact socket and a very strong breaker bar and place it against a strong part of the frame and just bump the engine over very carefully with the high voltage coil wire disconnected so that the engine won't start when you bump it over with the starter and make sure the socket and the breaker bar are very secure when doing this. I recently bought the special Honda wrench from Snap-On tools and it works great for this, but it's very expensive but it's the only way to hold the Harmonic Pulley sufficiently in order to tighten it back to the recommended torque. Which can be several hundred ft pounds, see the service manual for the exact torque.

Aug 23, 2009 | 1992 Honda Accord

1 Answer

I have a 95 mazda b2300 timing belt broke I tried to install new belt went by the book on lining up the marks and it still wont start

Is you harmonic balencer back on? If it has timing sencer, it won't fire if it does'nt know when to fire.

Jul 16, 2008 | 2007 Mazda B2300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides