Question about 1994 Chevrolet Caprice Classic

1 Answer

Water pump is leaking and its not the o-ring on the front cover of the water pump and its the pump that runs off the cam shaft and there is a hole in the bottom the bleeder valve what should i do

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 303 Answers

That is the weep hole when the pump diaphram goes bad it leaks there you need a pump

Posted on Oct 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Oil leak on a '92 Geo Tracker. Installed an O Ring, but still leaking. Any suggestions?


O-ring where? The drain plug? Distributor shaft? Or do you mean oil seal?
Geo oil drain plug specifies a compressible copper ring washer I think? Need to clean the surfaces well, and torque to spec. My own plug's seal is not perfect, but only a drop here and there usually. Autozone or NAPA can supply you a new plug and washer if needed.

Apr 19, 2015 | 1992 Geo Tracker

1 Answer

If the water pump is leaking, where will you see the leak? Bottom of P.S. bracket at back of timing cover or out timing cover @ crankshaft, front of timing cover?


Look under the pump on the pulley shaft. there should be a little hole, if water leaks it will come out there.

Mar 17, 2015 | Cars & Trucks

1 Answer

Losing a lot of coolant. I don't see a leak. I started to drain the system and it smells burnt to s**t. What might my problem and possible solutions be?


see this causes and fix it. God bless you
Water pump -- A bad shaft seal will allow coolant to dribble out of the vent hole just under the water pump pulley shaft. If the water pump is a two-piece unit with a backing plate, the gasket between the housing and back cover may be leaking. The gasket or o-ring that seals the pump to the engine front cover on cover-mounted water pumps can also leak coolant. Look for stains, discoloration or liquid coolant on the outside of the water pump or engine.
Radiator -- Radiators can develop leaks around upper or loser hose connections as a result of vibration. The seams where the core is mated to the end tanks is another place where leaks frequently develop, especially on aluminum radiators with plastic end tanks. On copper/brass radiators, leaks typically occur where the cooling tubes in the core are connected or soldered to the core headers. The core itself is also vulnerable to stone damage. Internal corrosion caused by old coolant that has never been changed can also eat through the metal in the radiator, causing it to leak.
Most cooling systems today are designed to operate at 8 to 14 psi. If the radiator can't hold pressure, your engine will overheat and lose coolant.
Hoses -- Cracks, pinholes or splits in a radiator hose or heater hose will leak coolant. A hose leak will usually send a stream of hot coolant spraying out of the hose. A corroded hose connection or a loose or damaged hose clamp may also allow coolant to leak from the end of a hose. Sometimes the leak may only occur once the hose gets hot and the pinhole or crack opens up.

Sep 28, 2012 | Cars & Trucks

1 Answer

Water pump 2000 3.0 liter dodge caravan


For The 3.0 Motor. (3.3 Way down the line.)

Drain cooling system.
Remove timing belt. Refer to Engine for procedure.
Remove water pump mounting bolts.
Separate pump from water inlet pipe and remove water pump.

Timing Belt Removal
Raise vehicle and remove accessory drive belt splash shield (Fig. 66).
Remove accessory drive belts.
Remove crankshaft pulley and damper (Fig. 68).
Support engine and remove right side engine mount.
Remove engine support bracket (Fig. 67).
Remove timing belt covers (Fig. 67).
Mark belt running direction for installation (Fig. 69).
Loosen timing belt tensioner bolt (Fig. 71) and remove timing belt.
Remove crankshaft sprocket flange shield (Fig. 68). CAMSHAFT SPROCKETS To remove camshaft sprockets
Hold camshaft sprocket with Spanner Tool MB-990775. Loosen and remove bolt and washer (Fig. 70).
Remove camshaft sprocket from camshaft. To install camshaft sprockets:
Place camshaft sprocket on camshaft.
Install bolt and washer to camshaft. Using Spanner Tool MB-990775, hold camshaft sprocket and torque bolt to 95 Nm (70 ft. lbs.) (Fig. 70). TIMING BELT TENSIONER
Install timing belt tensioner and tensioner spring.
Hook spring upper end to water pump pin and lower end to tensioner bracket with hook out (Fig. 71).
Turn timing belt tensioner counterclockwise full travel in adjustment slot and tighten bolt to temporarily hold this position (Fig. 72).

INSTALLATION


Install timing belt on crankshaft sprocket and keep belt tight on tension side (Fig. 69). Install belt on the front (radiator side) camshaft sprocket. Install belt on the water pump pulley, rear camshaft sprocket and finally on the timing belt tensioner.
Rotate the front camshaft sprocket in opposite direction to take up belt slack. Check that all timing marks are aligned (Fig. 69).
Install crankshaft sprocket flange (Fig. 68).
Loosen tensioner bolt and allow spring to tension timing belt.
Turn crankshaft two full turns in clockwise direction. Turn smoothly and in clockwise direction ONLY.
Align the timing marks on the sprockets and tighten the timing belt tensioner locking bolt to 28 Nm (250 in. lbs.) torque.
Install timing belt covers.
Install engine support bracket.
Install right side engine mount.
Install crankshaft damper and pulleys (Fig. 68). Tighten damper center bolt to 135 Nm (100 ft. lbs.) .
Install accessory drive belts.
Install accessory drive belt splash shield (Fig. 66).

Be sure to also replace all the cam and crank seals why you are there. Might as well put a belt on too.

FOR THE 3.3 OR 3.8 MOTORS.

Drain Cooling System.
Remove accessory drive belt.
Remove right front lower fender shield.
Remove water pump pulley bolts and remove pulley.
Remove water pump mounting screws. Remove water pump.
Remove and discard O-ring seal.
Clean O-ring groove and O-ring surfaces on pump and chain case cover. Take care not to scratch or gouge sealing surface

Installation

Install new O-ring into groove.
Install water pump to chain case cover. Tighten screws to 12 Nm (105 inch lbs.) .
Rotate pump by hand to check for freedom of movement.
Position pulley on pump. Install screws and tighten to 30 Nm (250 inch lbs.) .
Install accessory drive belt.
Install right front lower fender shield.
Refill Cooling System.

FOR THE 2.4 MOTOR

Disconnect negative cable from battery.
Raise vehicle on a hoist. Remove right inner splash shield.
Remove accessory drive belts.
Drain cooling system.
Support engine from the bottom and remove right engine mount.
Remove right engine mount bracket.
Remove timing belt. Refer to Engine for procedure.
Remove timing belt idler pulley.
Hold camshaft sprocket with Special tool C-4687 and adaptor C-4687-1 while removing bolt. Remove both cam sprockets.
Remove rear timing belt cover.

Install new O-ring gasket in water pump body O-ring groove. CAUTION: Make sure O-ring is properly seated in water pump groove before tightening screws. An improperly located O-ring may cause damage to the O-ring and cause a coolant leak.
Assemble pump body to block and tighten screws to 12 Nm (105 inch lbs.) . Pressurize cooling system to 15 psi with pressure tester and check water pump shaft seal and O-ring for leaks.
Rotate pump by hand to check for freedom of movement.
Install rear timing belt cover.
Install camshaft sprockets and torque bolts to 101 Nm (75 ft. lbs.) .
Install timing belt idler pulley and torque mounting bolt to 61 Nm (45 ft. lbs.) .
Install timing belt. Refer to Engine for procedure.
Install right engine mount bracket and engine mount. Refer to Engine for procedure.
Fill cooling system.
Install accessory drive belts.
Lower vehicle and connect battery cable.

Mar 29, 2012 | Cars & Trucks

1 Answer

Antifreeze leaked out from somewhere in the back of motor .the two front holes are not leaking no check engine.temp gauge rises to the top cant see the leak i just here pressure being released and some...


if it is coming from behind the r front tire and is a 4cyl the water pump has an o-ring that fits between pump and block and is behind timing cover where you can not see it. usually if it is leaking you can look under car at the engine on r-side at p/s pump area and can see where coolant has run down oil pump to oil pan from behind t-cover. hope this helped give me more info if not and good luck................

Jun 17, 2011 | 1994 Toyota Camry

3 Answers

Where is the water pump located on a 1996 olds aurua the car is over heating


Hi, i would check the thermostat first unless the water pump is leaking as the water pump is where the timing belt is is the timing belt needs removing to get to the pump, take the thermostat out and place it in a tub of boiling water and check if it opens up if it dont then it will need replacing.

you need to bare in mind that it could also be head gasket failure so make sure you get this tested if the thermostat is found to be in working order.

let me know if you need further assistance ok

Sep 14, 2010 | 1996 Oldsmobile Aurora

3 Answers

1995 toyota camry leaking oil from behind the timing belt cover. Isn't this a major repair? Is the leak more than likely a camshaft seal?


If you haven't had the timing belt replace (60,000 miles is the suggested service intervale) this is an overlap of having the timing belt replaced.
If the timing belt is not due for replacement and its the cam shaft seal that is leaking. Its a pretty easy fix. Remove the top timing belt cover , and the crankshaft sensor wiring you may have to remove the front engine mount . Set #1 piston at TDC, Loosen tensioner w/ spring slip off belt. **Remove sprocket pull out old seal with a sharp pick. Greese and install new seal make sure its flush with its bore . Reistall sprocket. Slide belt over Cam sprocket tighten tensioner. Install cover and mount (if applicable) Check timing marks by turning crank two revolutions.
** If CamSprocket Bolt is difficult to remove then remove valve cover and use a 21mm wrench to hold the Camshaft while you crack off Cam Sprocket Bolt.
You will see the groves on the Camshaft where you can place a wrench to hold the shaft.
After you replaced the seal replace the valve cover gasket ONLY IF YOU HAD TO REMOVE THE COVER TO HOLD THE CAM WHILE REMOVING ITS BOLT.

This is about as major as it gets.

May 12, 2010 | 1995 Toyota Camry

2 Answers

Overheating


Check the water pump belt and make sure it did not come off the water pump pulley.It is on the rear of the valve cover on the front of the vehicle.It is run by the cam shaft.Hope this helps.Good luck.

Mar 29, 2010 | 1997 Cadillac DeVille

1 Answer

How do i get to the water pump on a 1998 nissan altima


THE 2.4L AND 2.5L ENGINES.YOU HAVE TO SAFELY RAISE VECHICLE SUPPORT IT USING JACK STANDS.YOU HAVE TO REMOVE THE RIGHT HAND SPLASH SHIELD.THEN LOOSEN WATER PUMP PULLEY BOLTS LEAVE DRIVE BELT IN PLACE TO KEEP WATER PULLEY FROM TURNING WHILE LOOSEN PULLEY BOLTS.THEN YOU HAVE TO MOVE AC COMPRESSOR DONT DISCONNECT ANY REFRIGERANT LINES.JUST SET IT ASIDE THE ALTERNATOR AND ITS MOUNT ALSO HAS TO MOVED.THEN YOU ARE AT WATER PUMP.NOW THE 3.5L ENGINE WATER PUMP IS IN A TOUGH SPOT.YOU HAVE TO REMOVE ENGINE SPLASH SHIELD.REMOVE THE SUBFRAME BRACKET FROM THE RIGHT SIDE OF THE SUBFRAME ASSEMBLY. REMOVE THE INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM FROM THE ENGINE COMPARTMENT.REMOVE THE IPDMER UPPER COVER AND HARNESS COVER RELEASE THE TWO CLIPS.DISCONNECT THE ELECTRICAL CONNECTORS AND LIFT THE ASSEMBLY FROM THE CASE.REMOVE THE RADIATOR SHROUDS REMOVE THE DRIVE BELTS.REMOVE THE ENGINE COOLING FAN.REMOVE THE RADIATOR AND THE COOLANT RESERVOIR.REMOVE THE IDLER PULLEY AND THE POWER STEERING AND ALTERNATOR ADJUSTMENT BRACKETS.REMOVE THE FRONT ENGINE MOUNT.REMOVE COOLANT DRAIN PLUG FROM THE WATER PUMP SIDE OF THE ENGINE BLOCK.REMOVE CHAIN TENSIONER COVER AND THE WATER PUMP COVER FROM THE ENGINE FRONT COVER.REMOVE THE CHAIN TENSIONER.PULL THE LEVER DOWN TO RELEASE THE PLUNGER STOPPER TAB.INSERT A STOPPER PIN INTO THE TENSIONER BODY HOLE TO RETAIN THE LEVER IN THE RELEASED.NO CHAIN TENSION POSITION.MOVE THE PLUNGER INTO THE TENSIONER BY PRESSING THE CHAIN GUIDE AND PUSHING WITH A SCREWDRIVER.MAKE A GAP BETWEEN THE WATER PUMP GEAR AND THE TIMING CHAIN BY ROTATING THE CRANKSHAFT PULLEY 20 DEGREES COUNTERCLOCKWISE.REMOVE THE THREE WATER PUMP MOUNTING BOLTS.INSTALL 2 BOLTS SIZE M8 1.25 X 50 MM INTO THE WATER PUMP BOLT HOLES AND TIGHTEN THEM EQUALLY UNTIL THEY BOTTOM AGAINST THE CHAIN COVER.IT WILL BE NECESSARY TO ROTATE THE WATER PUMP SLIGHTLY TO ALLOW THE BOLTS TO DRIVE AGAINST THE REAR TIMING CHAIN CASE COVER INSTEAD OF THE BOLT HOLES.REMOVE THE WATER PUMP.CLEAN THE SEALANT FROM THE MATING SURFACE AND REPLACE THE O-RINGS.INSTALL THE OUTER O-RING WITH THE WHITE PAINT MARK FACING THE FRONT OF THE ENGINE AND THE INNER O-RING BLACK NEXT.APPLY A LIGHT AMOUNT OF OIL TO THE O-RINGS.TIGHTEN THE WATER PUMP BOLTS TO 62 - 89 INCH POUNDS.TIGHTEN WATER PUMP BOLTS EVENLY DONT OVER TIGHT OR YOU WILL DAMAGE WATER PUMP AND HAVE LEAKS.REINSTALL THE POWER STEERING AND ALTERNATOR ADJUSTMENT BRACKETS AND ANY OTHER COMPONENTS REMOVED FOR ACCESS TO THE WATER PUMP.REFILL THE COOLING SYSTEM.RUN THE ENGINE AND CHECK FOR LEAKS.YOU NEED TO BUY THE HAYNES REPAIR MANUAL.SO THE PHOTOS WILL HELP YOU WHEN REMOVING AND INSTALLING WATER PUMP.

Nov 14, 2009 | Nissan Altima Cars & Trucks

1 Answer

I have a coolant leak coming from the front of the engine. looks like it is leaking around the cam shaft pulley. The vehicle is a 2001 Nissan Frontier v6


Sounds like either the water pump or the thermostat housing. The water pump has a small hole in the bottom where the shaft comes through, when the water pump gets worn it will leak here so you know to replace the pump. The thermostat housing will be at the motor end of the upper radiator hose where it attaches to the motor. Hope this helps.

Aug 11, 2008 | Nissan Frontier Cars & Trucks

Not finding what you are looking for?
1994 Chevrolet Caprice Classic Logo

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...