Question about 1993 Nissan 240SX

1 Answer

Water pump how to put on water pump

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 37 Answers

This covers it from start to finish

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Engine+Electrical&partName=Engine+%26+Engine+Overhaul&pageId=0900c152800996da&subChapterTitle=Water+Pump&partId=0900c1528009969a#hd1-1-1

Posted on Apr 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace water pump torrent


drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs torque.you should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

I need to replace the water pump and put the car back to geather


For water pump replacement i suggest you to check the help link provided below.

click the link below :----

Water pump replacing procedure for all vehicles?

http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
---------

HOW TO REPLACE A WATER PUMP

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

------------------
How to route Water Pump Belt for 1992 Oldsmobile ?

http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

---------
How to replace Water Pump on Car ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

---------
How to Remove Water Pump?

http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

-------
Where is Water Pump located ?

http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

-----------

This will help. Thanks.

Jan 21, 2012 | 1996 Mitsubishi Galant

1 Answer

Losing water and running hot.water is not leaking out onto ground.just have to keep putting water in car


Ur car is having a clogging water pump or a dying water pump problems.The car water pump it is not doing it job like circulation of the water in the car through out the car engine evenly.The car keep losing water that u keep putting it in because of the car engine keep overheating and causes water candensation and evaporation of the water u keep putting it into the car.This car must have be check out by an auto mechanic for changing it holes systems on the car water pump or must have be do a replacement of the whole water pump unit itself.

Sep 28, 2011 | Cars & Trucks

1 Answer

Need instruction for replacing water pump 2004 GMC Envoy 4.2 liter engine.


TO REPLACE WATER PUMP.FIRST YOU HAVE TO DRAIN THE COOLANT SYSTEM. REMOVE AIR INTAKE DUCT AND RESONATOR. REMOVE THE RADIATOR SHROUD AND FAN CLUTCH ASSEMBLY REMOVE THE DRIVE BELT. REMOVE WATER PUMP PULLEY.YOU NEED A PIN SPANNER WRENCH OR STRAP WRENCH TO HOLD WATER PUMP PULLEY WHILE LOOSEN WATER PUMP PULLEY BOLTS .YOU CAN BUY STRAP WRENCH OR RENT PIN SPANNER WRENCH AT AUTO ZONE PARTS STORES OR OTHER STORES HAS TOOLS CAN BE RENT. ONCE WATER PUMP PULLEY REMOVED. REMOVE THE WATER PUMP MOUNTING BOLTS. REMOVE WATER PUMP. IF WATER PUMP STUCK YOU CAN TAP WITH SOFT FACE HAMMER OR A LONG PIECE OF ROUND WOOD.WHEN WATER REMOVED.YOU NEED TO CLEAN THE SEALING SURFACE CAREFUL DONT SCRATCH SEALING SURFACE. YOU CAN BUY CAN OF SPRAY GASKET REMOVER.CLEAN SURFACE GOOD THEN WIPE WITH LACQUER THINNER OR ACETONE.THEN GET WATER PUMP NEW GASKET MATCH HOLES UP WITH GASKET TO WATER PUMP. ONCE HOLES MATCH UP APPLY RTV SEALANT ON BOTH SIDES WATER PUMP GASKET. THEN PUT GASKET ON WATER PUMP THEN INSTALL WATER PUMP TO VECHICLE.TORQUE WATER PUMP BOLTS TO 89 INCH LBS .TIGHTEN WATER PUMP PULLEY BOLTS TO 18 FT LBS THEN PUT EVERY THING BACK VISA VERSA.

Aug 26, 2011 | GMC Envoy XL Cars & Trucks

1 Answer

Where do you put water in the water pump on a 2002 alero?


Well you must put the water in the radiator or deposit for water that your car has instead of the water pump, the water pump is an internal part bolted in the engine that has a pulley that makes circulate the water inside the engine.

Jun 27, 2011 | 2002 Oldsmobile Alero

3 Answers

Water pump leaks


If your water pump is leaking, that is the first sign of a bad water pump. This means that you will have to replace the water pump.

Feb 28, 2011 | 1997 Oldsmobile Regency

1 Answer

How do you change the water pump on a 1998 buick skylark?


Hi This is d_hubbs: Removal and replacement of your water pump.I'm assuming you have a 2.5 Engine.You did'nt give your engine Information but about 75% of your Year and Model had the 2.5 in them.
1st start by disconnecting your negative cable on your Battery. Then Drain your Coolant into a Container: then remove your drive belts remove your fan from the water pump: You probally should also remove your alternator and A/C Compressor to make it easier to get to your water pump, now remove your lower Radiator Hose, then remove your water pump mounting bolts, now remove the water pump: Now Clean the water pump surface on your engine where your gasket will be. Besure its Clean Good : NOTE: Sometimes if you purchase a New water pump it will not have the drive belt pulley on it. if this is the case Remove your Pulley from your old Pump and install it on your New pump : now Run some gasket sealer on your new water pump where the gasket will go.put gasket on the new pump lining up your mounting bolt holes.also put a small bead of sealer on the engine where your water pump will mount: now Mount your New water pump to the engine with the Mounting Bolts.Torque the Mounting bolts at 25-30 Foot Lbs.
Inspect your Drive belts and Hoses its a good time to put new ones on if needed.Now put your lower Hose back on-re-install your A/C compressor and Alternator-Put your fan back on-now put All your Drive belts back on be sure to Adjust the Belt Tension and Lock down the Bolts.-Fill your Radiator back up with coolant,If the Fluid you took out is still fairly new ,you can use it. If its Aged best off putting new Coolant. Replace the Battey Cable Start your Car and Check for any Leaks , After your Thermastat opens you'll need to recheck your Coolant Level. if no Leaks and Cooling System is Full you Are Done. Please let me know how my advice and Solutions have Helped you. Thanks for Using FIXYA From d_hubbs

Jun 09, 2010 | 1998 Buick Skylark

1 Answer

WATER PUMP REPLACE DIAGRAM


  1. Step 1 Drain the antifreeze from cooling system. Remove belt from water pump. Examine and see if you have to remove anything else to get out the water pump. If so make a diagram of everything you are removing so you can put it back together.
  2. Step 2 Remove the hoses from the water pump. Find all bolts holding the water pump in . Loosen each one a little bit. After all are lose you can then remove them. Remove water pump. Put new gasket on and install new water pump. Hook up hoses to water pump. Look at your diagram and replace everything you had to remove earlier. Put the belt back on.
  3. Step 3 Shut the drain on system and refill cooling system. Make sure you use the antifreeze that is designed for system. Run engine for a couple of minutes. Check for leaks and check coolant level. Add if necessary. If there is no leaks you are ready to go.

Jun 04, 2010 | 2001 Mazda MPV

1 Answer

Water pump


Hello drain the water from the radiator by removing the hose from the radiator to the water pump,after having taken out the hoses,then unscrew the bolts that hold the water pump.After having taken the pump,clean the surface where the pump is fitted on the engine.Now when putting,the new pump,put a clear layer of silicone gasket on the surface where the pump will fit to prevent leakage,now you screw the bolt to the same torque,then after put the hose back like it was before,fill your radiator ,do not put the cap now,because of an air lock in the water circuit,start the engine,you will see the water level lower,fill it to its level,then put the radiator cap.Hope that help you in changing the pump,good luck

Dec 26, 2009 | 2000 Nissan Maxima

2 Answers

Water pump


buy a new water pump, remove the radiator, remove the hose from the pump, remove the bolts that holds the pump, remove the old pump.

put the new gasket in the pump, dont forget to put a little bit of grease just to hold the gasket inplace. put the new pump, use the old bolts from where they are taken ( sometimes they are not of equal length ). if you have a torque wrench then use it to tighten the bolts with equal amounts of torque. put the hose back, put the radiator back, put water in the radiator, run the engine and look for some leaks at the new pump.

i hope i did it..

tnx, drcool

Jul 28, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1993 Nissan 240SX Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63572 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...