Question about 1992 Toyota Paseo

1 Answer

I re-aligned all both my cam sproket and crankshaft sprocket to specs and installed the timing belt. The car will turn on but wont accelerate. Thinking i misaligned the sprokets, i took everything out again and re-aligned the sprockets to specs and put back the timing belt, cover, pulley, and v-belts. I made sure i didnt mess up the timing when i put in the timing belt. The car will not raise rpm past 1500. I did not use a timing light to adjust the distrubitor. Could that be the problem??car starts fine but does not go past 10mph and rpm is stuck at 1500. Please help!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 2,122 Answers

Are you sure you have the correct marks?....The crankshaft marks wont be a problem, but the cams may be....There's usually a hole through the cam pulley and that should be lined up with a punch mark behind it....That will be on the camshaft cap....But you may be looking in the wrong place. Have a look at the map sensor, which is mounted onto the bulkhead firewall, about half way across the engine bay, near the top....It has an electrical socket with three cables going into it and a vacuum pipe which connects to the surge tank....Thats the part of the intake manifold which is cylindrical in shape....Make sure the pipe and the electrical connector are in place....
If that's all ok, next thing is to replace the fuel filter. There are two places it may be mounted....The most likely is under the hood (Bonnet) on the fire wall....Thats what the bulkhead that separates the cabin and engine compartment is called....Take a look down past the gear box close to the corner....The second place it can be is close to the fuel tank underneath the car....
If that's not the problem, have the fuel pump output pressure checked....For that you'll need a pressure guage, and it may be better to take it to a shop, if you don't have one....The pump is supposed to have an output of around three and a half bar or above when it's in the fuel circuit with the engine running....Make sure the knock sensor hasn't been damaged and the cable is still connected....
Also check the battery voltage to make sure your getting enough spark to th ignition system....
The last part which I believe maybe causing the problem can be the ignition system, and there you should try a new igniter....
let me know how you get on and when you do, let me know what engine and what ignition system you have in your car....If what I've said doesn't work out I'd like to know more about the car so we can put our heads together....Regards Johngee



Posted on Oct 14, 2010

Testimonial: "thank you so much for your help! I rechecked everything i did and now i just finished adjusting my ignition timing(was way off) and now it runs great"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.2 v6 dohc izuzu cylinder head torque specs. and timing marks diagrams including cam lobes. positions please anyone?


yet again
no car body stated, an ISUZU WHAT?> is this too much to ask?
no country,
no year stated,
and the poster dont know all books are indexed by...
drum roll, country model, then year., (all 3 missing, is this fun?)
and this engine, is twin cam.. the correct name is
6ve1 99 to 2004? is 3.5L
the early 2 cam is called 6VD1W (w= 4 cams total)
1998 to 2002 on usa spec troopers (guess #2)

the 2 cams in one head are gear driving side by side,
we have posted this answer on this forum over 5 times
search much>?

did i guess right? so now ill post again this data. using online official sources, not rag books.
photos posted yet again, here we go, the hard way, guessing the freakn car,.. wow.
called the VIN V engine. here.USA>






26271340-uzkuy1j30zzkgz3vrz2nwusy-5-0.jpg
and the words


  1. Verify that the sprocket timing marks are still aligned and that the groove and the keyway on the crankshaft timing sprocket align with the mark on the oil pump. The white pointers on the camshaft timing sprockets should align with the dots on the front plate.
  2. Install the timing belt. Use clips to secure the belt onto each sprocket until the installation is complete. Align the dotted marks on the timing belt with the timing mark opposite the groove on the crankshaft sprocket. NOTE The arrows on the timing belt must follow the belt's direction of rotation. The manufacturer's trademark on the belt's spine should be readable left-to-right when the belt is installed.
  3. Align the white line on the timing belt with the alignment mark on the right bank camshaft timing pulley. Secure the belt with a clip. WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.
  4. Rotate the crankshaft counterclockwise to remove the slack between the crankshaft sprocket and the right camshaft timing belt sprocket.
  5. Install the belt around the water pump pulley.
  6. Install the belt on the idler pulley.
  7. Align the white alignment mark on the timing belt with the alignment mark on the left bank camshaft timing belt sprocket.
  8. Install the crankshaft pulley and tighten the center bolt by hand. Rotate the crankshaft pulley clockwise to give slack between the crankshaft timing belt pulley and the right bank camshaft timing belt pulley.
  9. Insert a 1.4mm piece of wire through the hole in the pusher to hold the rod in. Install the pusher assembly while pushing the tension pulley toward the belt.
  10. Pull the pin out from the pusher to release the rod.
  11. Remove the clamps from the sprockets. Rotate the crankshaft pulley clockwise 2 turns. Measure the rod protrusion to ensure it is between 0.16-0.24 in. (4-6mm).
  12. If the tensioner pulley bracket pivot bolt was removed, tighten it to 31 ft. lbs. (42 Nm).
  13. Tighten the pusher bolts to 14 ft. lbs. (19 Nm).
  14. Remove the crankshaft pulley. Install the lower and upper timing belt covers and tighten their bolts to 12 ft. lbs. (17 Nm).
  15. Fit the oil cooler hose onto the timing cover and tighten its mounting bracket bolts to 16 ft. lbs. (22 Nm).
  16. Install the crankshaft pulley and tighten the pulley bolt to 123 ft. lbs. (167 Nm).
  17. Install fan pulley assembly and tighten the bolts to 16 ft. lbs. (22 Nm).
  18. Install and adjust the accessory drive belts.
  19. Install the cooling fan assembly and tighten the bolts to 72 inch lbs. (8 Nm).
  20. Install the upper fan shroud.
  21. Install the air cleaner assembly and intake air duct.
  22. Connect the negative battery cable

26271340-uzkuy1j30zzkgz3vrz2nwusy-5-1.jpg

26271340-uzkuy1j30zzkgz3vrz2nwusy-5-3.jpg

26271340-uzkuy1j30zzkgz3vrz2nwusy-5-6.jpg and wants head torque too, need egg in your beer?

Aug 31, 2016 | Isuzu Cars & Trucks

1 Answer

Cam timing for fiat siena 1.2 2001


There are no timing marks on this engine - the engine has to be "locked" using special engine locking / setting kit which you wil have to obtain to do the job.

I will give you the instructions to do the job for when you have the locking kit to do the job.. as follows:

Removal
  1. Raise and support front of vehicle.
  2. Remove:
      • RH front wheel.
      • RH inner wing panel.
      • Air filter assembly.
  3. Support engine.
  4. Remove:
      • RH engine mounting and bracket.
      • Timing belt upper cover,
      • AC receiver/drier (if fitted). DO NOT disconnect hoses.
      • Timing belt lower cover.
      • Auxiliary drive belt.
      • Support bracket between gearbox and cylinder block (Palio).
  5. Palio: Remove bell housing cover plate. Fit flywheel locking tool. Tool No.1.867.029.000. or equivalent commercially available.
  6. Remove:
      • Crankshaft pulley bolts
      • Crankshaft pulley
      • Spark plug leads.
      • Ignition coil and bracket.
      • Spark plugs.
  7. Fit dial gauge and adapter to No.1 cylinder. Tool No.1.860.895.000.
  8. Turn crankshaft to TDC on No.1 cylinder. Set dial gauge to zero.
  9. Ensure notch in rear of camshaft aligned as shown.
  10. Install camshaft aligning tool. Tool No.1.870.823.000

  11. NOTE: If camshaft aligning tool cannot be fitted: Turn crankshaft one turn clockwise.

Installation
  1. Ensure No.1 cylinder at TDC by turning crankshaft slightly clockwise and anti-clockwise. Use dial gauge .
  2. Ensure camshaft aligning tool fitted correctly
  3. Hold camshaft sprocket. Use tool No.1.860.831.000/001
  4. Slacken camshaft sprocket bolt
  5. Fit timing belt in following order:
      • Crankshaft sprocket.
      • Water pump sprocket.
      • Camshaft sprocket.
      • Tensioner pulley.
    NOTE: Observe direction of rotation marks on belt.
  6. Fit tensioning tool locating pegs to tensioner pulley holes -Tool No.1.860.745.100/300. Ensure tensioning tool arm is horizontal.
  7. Set weight at 70 mm mark on scale bar.
  8. Hold camshaft sprocket
  9. Tighten camshaft sprocket bolt - Tightening torque: 70 Nm.
  10. Remove aligning tool
  11. Turn crankshaft two turns clockwise.
  12. Ensure No.1 cylinder at TDC by turning crankshaft slightly clockwise and anti-clockwise. Use dial gauge
  13. Ensure camshaft aligning tool can be fitted - If not: Repeat installation procedure.
  14. Tighten tensioner nut to 28 Nm
  15. Remove:
      • Tensioning tool
      • Camshaft aligning tool
      • Dial gauge
  16. Install components in reverse order of removal.
  17. Tighten crankshaft pulley bolts - Tightening torque: 20 Nm + 90°.

Jun 26, 2016 | Fiat Cars & Trucks

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

Hi, I am looking for a timing belt diagram for a 1998 2.5ltr Subaru Outback or can you tell me which timing marks on the sprockets line up to the encasing.


Timing Belt Cover, Belt & Sprockets Removal & Installation 2.5L Engine To Remove:
  1. Remove the drive belts.
  2. Remove the A/C compressor drive belt tensioner. Timing belt & cover DOHC exploded view subaru-03-25-6470.gif

  3. Remove the crankshaft pulley.
  4. Remove the mounting bolts and left timing belt cover.
  5. Remove the mounting bolts and right timing belt cover.
  6. Remove the mounting bolts and front timing belt cover.
  7. Vehicles W/ M/T: Remove the timing belt guide.
  8. Ensure that the timing belt rotation arrows are still visible. If the marks are worn off, place new rotation marks on the belt. Timing belt alignment marks DOHC subaru-03-25-6472.gif

  9. Turn the crankshaft using a breaker bar and special adapter socket on the crankshaft. Align the timing mark on the crankshaft sprocket (1), left intake sprocket (2), left exhaust sprocket (3), right intake sprocket (4) and right exhaust sprocket (5) with the notches in cylinder block and timing belt cover.
  10. Paint alignment marks on the timing belt at the crankshaft and camshaft sprockets timing marks. CAUTION
    Do not turn the camshaft sprockets with the timing belt removed. The valves heads will contact each other causing the valve stems to bend.
  11. Remove the lower right idler pulley.
  12. Remove the timing belt.
  13. Remove the upper right idler pulley.
  14. Remove the lower left (toothed) idler pulley.
  15. Remove the belt tensioner.
  16. Hold the sprocket and remove the left intake and exhaust camshafts.
  17. Hold the sprocket and remove the right intake and exhaust camshafts.
  18. Remove the crankshaft sprocket.
To Install:
  1. Install the crankshaft sprocket.
  2. Hold the sprocket and install the right intake and exhaust camshafts with the mounting bolts. Tighten 58 ft-lb (78 Nm).
  3. Hold the sprocket and install the left intake and exhaust camshafts with the mounting bolts. Tighten 58 ft-lb (78 Nm).
  4. Reset the automatic belt tensioner as follows:
    • Remove the mounting bolt and belt tensioner. NOTE: Do not exceed more than 2,205 lb. (9,807 N).
    • Place the belt tensioner on a press. Press the adjuster rod down gradually (using more than 3 minutes) 66- lb (165 N) or more until the adjuster rod is aligned with the stop pin hole in the cylinder.
    • Insert a 0.08 in (2 mm) diameter pin or hex wrench into the pin hole to lock the adjuster rod.
    • Install the automatic belt tension adjuster with the mounting bolt. Tighten 18 ft-lb (25 Nm).
  5. Install the lower left (toothed) idler pulley. Tighten 29 ft-lb (39 Nm).
  6. Install the upper right idler pulley with the mounting bolt. Tighten 29 ft-lb (39 Nm). Crankshaft sprocket and oil pump cover alignment marks 2.5L DOHC subaru-03-25-4890.gif

  7. Align the timing mark on the crankshaft sprocket with the mark on the oil pump cover. Timing belt alignment marks DOHC subaru-03-25-6472.gif

  8. Align the single timing mark on the right exhaust camshaft sprocket with the notch on the timing belt cover.
  9. When the single timing mark on the right exhaust camshaft sprocket is aligned with the notch on the timing belt cover, ensure that the double lines on the intake camshaft and exhaust camshaft sprockets are aligned.
  10. Align the single timing mark on the left exhaust camshaft sprocket with the notch on the timing belt cover by turning the sprocket counter clockwise (viewed from front of engine).
  11. Ensure that the double lines on the intake camshaft and exhaust camshaft sprockets are aligned when the single timing mark on the left exhaust camshaft sprocket is aligned with the notch on the timing belt cover. CAUTION
    • The camshafts can be rotated independently causing the valves heads to contact each other resulting in bent valve stems.
    • When the timing belt is removed the camshafts will turn to the lowest cam lobe position by the force of the valve springs. Before installing the timing belt the 4 camshafts are in the lowest lift position (valves closed).
    • When the camshafts are rotated to install the timing belts, # 2 intake and # 4 exhaust cam lobes of the left camshafts are held to push their corresponding valves down. In this position, these valves are held in the open position. Right camshafts are held so their cam lobes do not push the valves down.
    • The left camshafts must be rotated from the lowest lobe position to the position where the timing belt can be installed at the smallest possible angle in order to prevent intake and exhaust valve contact. Camshaft sprockets rotation subaru-03-25-6473.gif

    • Do not turn the camshafts in the direction shown in the illustration because the valves will open at the same time and contact each other.
    CAUTION
    If the timing belt alignment is off the mark buy more than 3 teeth, the valves and pistons may have contact.
    Timing belt alignment marks DOHC subaru-03-25-6472.gif

  12. Align the timing marks on the belt with the marks on the sprockets in the numerical order shown in the illustration.
  13. Install the lower right idler pulley with the mounting bolt. Tighten 29 ft-lb (39 Nm).
  14. Ensure that the timing mark alignment is correct and remove the tensioner stop pin.
  15. Vehicles W/ M/T: Install the timing belt guide and temporarily tighten the mounting bolts.
  16. Vehicles W/ M/T: Measure the clearance between the guide and timing belt. The clearance should measure 0.039 ± 0.020 in (1.0 ± 0.5 mm).
  17. Vehicles W/ M/T: Tighten the guide bolts 7.2 ft-lb (9.8 Nm).
  18. Install and secure the front timing belt cover with the mounting bolts.
  19. Install and secure the right timing belt cover with the mounting bolts.
  20. Install and secure the left timing belt cover with the mounting bolts.
  21. Install the crankshaft pulley.
  22. Install the A/C compressor drive belt tensioner.
  23. Install the drive belts.
prev.gif next.gif

Sep 30, 2010 | Subaru Outback Cars & Trucks

1 Answer

Need to know what the timing marks and locations for replacing the timing belt


Timing Belt Removal & Installation 3.0L Engine To Remove:
Exploded view of the timing belt and sprocket assembly (3.0L engine) 86723255.gif

  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts. Remove the engine mount insulator from the engine support bracket.
  3. Remove the engine support bracket. Remove the crankshaft pulleys and torsional damper. Remove the timing belt covers.
  4. Rotate the crankshaft until the sprocket timing marks are aligned. The crankshaft sprocket timing mark should align with the oil pump timing mark. The rear camshaft sprocket timing mark should align with the generator bracket timing mark and the front camshaft sprocket timing mark should align with the inner timing belt cover timing mark.
  5. If the belt is to be reused, mark the direction of rotation on the belt for installation reference. Mark the direction of travel for the timing belt for correct installation 86723p72.jpg
  6. Loosen the timing belt tensioner bolt and remove the timing belt.
  7. If necessary, remove the timing belt tensioner. Turn the center tensioner pulley bolt until the timing belt has enough slack . . . 86723p73.jpg
    . . . then slide the timing belt off of the camshaft sprockets 86723p74.jpg
  8. Remove the crankshaft sprocket flange shield and crankshaft sprocket.
  9. Hold the camshaft sprocket using spanner tool MB990775 or equivalent, and remove the camshaft sprocket bolt and washer. Remove the camshaft sprocket.
To Install:
  1. Install the camshaft sprocket on the camshaft with the retaining bolt and washer. Hold the camshaft sprocket using spanner tool MB990775 or equivalent, and tighten the bolt to 70 ft. lbs. (95 Nm).
  2. Install the crankshaft sprocket.
  3. If removed, install the timing belt tensioner and tensioner spring. Hook the spring upper end to the water pump pin and the lower end to the tensioner bracket with the hook out.
  4. Turn the timing belt tensioner counterclockwise full travel in the adjustment slot and tighten the bolt to temporarily hold it in this position.
  5. Rotate the crankshaft sprocket until its timing mark is aligned with the oil pump timing mark.
  6. Rotate the rear camshaft sprocket until its timing mark is aligned with the timing mark on the generator bracket.
  7. Rotate the front (radiator side) camshaft sprocket until its mark is aligned with the timing mark on the inner timing belt cover.
  8. Install the timing belt on the crankshaft sprocket while keeping the belt tight on the tension side. NOTE: If the original belt is being reused, be sure to install it in the same rotational direction.
  9. Position the timing belt over the front camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the rear camshaft sprocket and finally over the tensioner. CAUTION
    If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.
    Rent or borrow the special tool to hold the camshaft sprockets steady . . . 86723p75.jpg
    . . . while loosening the center retaining bolt on the camshaft pulley, then . . . 86723p76.jpg
    . . . remove the camshaft sprocket from the end of the camshaft 86723p77.jpg
    Timing belt tensioner and spring positions 86723254.gif
    Timing belt routing and timing mark locations 86723256.gif

  10. Apply rotating force in the opposite direction to the front camshaft sprocket (radiator side) to create tension on the timing belt tension side. Check that all timing marks are aligned.
  11. Install the crankshaft sprocket flange.
  12. Loosen the tensioner bolt and allow the tensioner spring to tension the belt.
  13. Rotate the crankshaft two full turns in a clockwise direction. Turn the crankshaft smoothly and in a clockwise direction only.
  14. Again line up the timing marks. If all marks are aligned, tighten the tensioner bolt to 250 in. lbs. (28 Nm). Otherwise repeat the installation procedure.
  15. Install the timing belt covers. Install the engine support bracket. Tighten the support bracket mounting bolts to 35 ft. lbs. (47 Nm).
  16. Install the engine mount insulator, torsional damper and crankshaft pulleys. Tighten the crankshaft pulley bolt to 112 ft. lbs. (151 Nm).
  17. Install the accessory drive belts.
  18. Reconnect the negative battery cable.
  19. Run the engine and check for proper operation.
prev.gif next.gif

Aug 17, 2010 | 1997 Dodge Caravan

2 Answers

Timming bailt marks for 1990 plym laser rs


REMOVAL & INSTALLATION 1.8L Engine
  1. If possible, position the engine so the No. 1 piston is at TDC.
  2. Disconnect the negative battery cable.
  3. Remove the timing belt covers.
  4. Remove the timing (outer) belt tensioner and remove the outer timing belt.
  5. Remove the outer crankshaft sprocket and flange.
  6. Remove the silent shaft (inner) belt tensioner and remove the belt. Fig. 1: Silent shaft belt timing marks — 1.8L engine 89573g93.gif
    Fig. 2: Checking the silent shafts for proper positioning 89573g94.gif
    Fig. 3: Timing belt timing mark alignment — 1.8L engine 89573g95.gif
    To install:
  7. Align the timing marks of the silent shaft sprockets and the crankshaft sprocket with the timing marks on the front case. Wrap the timing belt around the sprockets so there is no slack in the upper span of the belt and the timing marks are still aligned.
  8. Install the tensioner pulley and move the pulley by hand so the long side of the belt deflects about 1⁄4 in.
  9. Hold the pulley tightly so the pulley cannot rotate when the bolt is tigthened. Tighten the bolt to 15 ft. lbs. (20 Nm) and recheck the deflection amount.
  10. Install the timing belt tensioner fully toward the water pump and tighten the bolts. Place the upper end of the spring against the water pump body.
  11. Align the timing marks of the camshaft, crankshaft and oil pump sprockets with their corresponding marks on the front case or rear cover. NOTE: There is a possibility to align all timing marks and have the oil pump sprocket and silent shaft out of time, causing an engine vibration during operation. If the following step is not followed exactly, there is a 50 percent chance that the silent shaft alignment will be 180 degrees off.
  12. Before installing the timing belt, ensure that the left side (rear) silent shaft (oil pump sprocket) is in the correct position as follows:
    1. Remove the plug from the rear side of the block and insert a tool with shaft diameter of 0.31 in. (8mm) into the hole.
    2. With the timing marks still aligned, the shaft of the tool must be able to go in at least 2 1/2 in. If the tool can only go in about 1 in., the shaft is not in the correct orientation and will cause a vibration during engine operation. Remove the tool from the hole and turn the oil pump sprocket 1 complete revolution. Realign the timing marks and insert the tool. The shaft of the tool must go in at least 2 1/3 in.
    3. Recheck and realign the timing mark.
    4. Leave the tool in place to hold the silent shaft while continuing.
  13. Install the belt to the crankshaft sprocket, oil pump sprocket, then camshaft sprocket, in that order. While doing so, make sure there is no slack between the sprocket except where the tensioner is installed.
  14. Recheck the timing marks' alignment. If all are aligned, loosen the tensioner mounting bolt and allow the tensioner to apply tension to the belt.
  15. Remove the tool that is holding the silent shaft and rotate the crankshaft a distance equal to 2 teeth on the camshaft sprocket. This will allow the tensioner to automatically apply the proper tension on the belt. Do not manually overtigthen the belt or it will howl.
  16. Tigthen the lower mounting bolt first, then the upper spacer bolt.
  17. To verify correct belt tension, check that the deflection at the longest span of the belt is about 1⁄2 in.
  18. Install the timing belt covers and all related items.
  19. Connect the negative battery cable.

Aug 02, 2010 | 1990 Plymouth Laser

1 Answer

Timing belt instalation


as long as the the hole in the cam sproket is facing straight up and the crank on 0 youre timing should be good there are marks on the back plate for the cam sprocket its like a little indent line the hole up with that and the crank has a dot on the oil pump and a small v on the crank sprocket youre key way should be facing up on the crankshaft

Feb 26, 2010 | 1997 Toyota Camry

1 Answer

How do you align the camshaft & crankshaft timing marks 1.9


This is the same as a Ford Escort 1.9, the #1 cylinder should be all the way up. To confirm- the crak shift mark should be on zero which is Crank Shift Center- THe camshift sproket should align with the headmark. Make sure both marks don't move. Align the belt- not too tight , not to loose

Jul 12, 2009 | 1995 Mercury Tracer

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

3 Answers

How to replace timing belt on 1997 kia sportage


you have 2 sprokets to worry about the top two and crank gear, the crank gear has knocht on it and index on block ( towards back of gear visible from top) place on tdc mark ( top dead center), install the timing belt on this gear first then secure it with a piece of hose or anything that fits in between housing and belt to secure belt from moving from gear) then align the right side sproket on "E" for exhaust cam at top marks on cover and sprocket, then install belt over that sprocket, finally align left side sprocket "I" for intake to the top mark and install belt not too tight or it will make noise just make sure it is firm. now to double check from left to right with you standing in front of vehicle you should have left cam sprocket with "I" for intake to the top and right sproket with "E" for exhaust to the top. having bottom gear on tdc (top dead center mark) and all marks lined up with belt installed and proper tension secured, turn engine over twice and make sure marks meet in the same place then put everything back together. ( recommend you replace both idler and tension pulleys and check water pump, replace if needed or you'll be back.- this procedure goes the same to spectra, sephia, sportage, you will not damage the engine on these vehicles if belt goes out except rio. if timing belt goes out on the rio it will need an engine, if lucky just head. recommended replacement on all is every 60k miles) goo luck tightening the power steering drive belt when you put everything back together, just use a long bar to pry and good leverage. and a second hand comes in handy.

Aug 02, 2008 | 2002 Kia Sportage

Not finding what you are looking for?
1992 Toyota Paseo Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...