Question about 2001 GMC Denali

1 Answer

Loosening calipers? - 2001 GMC Denali

Posted by on

  • Sean Marovich Oct 14, 2010

    back calipers or front. most likely on the front calipers there is a torq bit socket you will need i believe it is a t-55 or t-40.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 22,219 Answers

If you mean rears then use a G clamp to apply light pressure and turn piston clockwise or go to auto factor and buy the right tool ,not expensive

Posted on Oct 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake caliper mounting bolts


They are standard thread, and very tight.
If you are facing the bolts from the back of the caliper, you turn counter-clockwise to loosen. If you are facing the caliper from the front you would turn them clockwise. You may need a very large breaker bar and socket to get them loose.

Jun 05, 2013 | 2001 Chevrolet Monte Carlo

1 Answer

How do i repla


replace front axle shaft you need to loosen axle nut with vechicle weight on the wheel just unloosen axle nut dont take axle nut all the way off just loosen it enough first remove hub cap to loosen axle nut.once loosen then raise vechicle remove wheel tire.you need to remove loosen brake caliper bolts just move brake caliper out of way support caliper piece of wire dont have to disconnect brake caliper hose just move it aside let it hang with a piece clothe hanger or piece or cord dont hang caliper by brake hose will damage brake hose.you need to remove brake caliper mounting bracket.go ahead remove axle nut.you have to remove steering knuckle bolts pull steering knuckle out of the strut bracket.you can remove front axle shaft by using large pry bar to the inner cv pry inner cv joint use a little leverage front axle should pop out.when you install new axle shaft push it in place until you hear it snap in place try pull by hand make sure half shaft in place. when done axle nut torque is 191 ft lbs.strut bracket bolts torque at 133 ft lbs.if this is your first time working on vechicle let a garage do the job.but buy the new shaft then take it with you for garage to replace be cheaper take own parts help cut down costs for part just pay for labor.

Apr 05, 2012 | 1994 Chevrolet Beretta

2 Answers

I dont know what bolt to loosen to bleed my brakes.


You need to loosen the Bleeder valve on the brake caliper, it is located on top of the caliper loosen it slightly and you will notice fluid start to run. If you are doing it our self you will need to let each one gravity bleed for about 15 min each. Hope that helps you

Aug 05, 2011 | Mazda Protege Cars & Trucks

1 Answer

Change the brake pads


when you pull the weel, you need to loosen the caliper from the rotor. once they are loosened, pry the caliper off the rotor. remove the old pads. use a caliper tool, you can rent one from an auto parts store or buy one, they are not expensive. use this tool to push the caliper piston back. place new pads, hook the caliper back on the rotor and fasten. replace the wheel. your done. barring any problems, it will be about a 10-15 min per wheel.

Jan 04, 2011 | 2000 Mazda Protege

1 Answer

Sticky brakes on front right rotor


Check the caliper ,and the caliper brake hose,if the caliper will lock down,and not release,loosen the bleeder screw on the caliper,if the caliper releases,the brake hose is bad,if it does not release the caliper is bad.

Nov 14, 2009 | 2004 Ford Focus

1 Answer

How to get bolt loose on caliper


heat the around the bolt with propene or matt gas and than try to loose it

Mar 30, 2009 | 1992 Toyota Camry V6

2 Answers

I am trying to loosen a caliper bleeder valve.


Try hitting the area around the bleeder with a hammer .. it may help .. bleeders are tough if they don't go after being heated/lubed. You could try loosening the line into the caliper .. that may allow enough of a bleed, banking on the fact that there is still brake fluid in that caliper .. otherwise you may end up replacing that caliper.

Feb 20, 2009 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...