Question about 1993 Geo Metro

1 Answer

Belts the belts keep flying off

Posted by on

  • BEEEK Jun 16, 2008

    I haven't tried anything, I keep replacing them.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 126 Answers

Sound slike something is not in line

Posted on Jun 21, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

Why dose my serpentine belt keep sliding off on my 2003 trailblazer

Aaron did you recheck the belt tension within 30 days after the installs?Me personally I pop the hood an have look see make sure it won't fly apart on me !

Nov 16, 2015 | 2003 Chevrolet TrailBlazer

1 Answer


Make sure the timing marks are aligned, or the system has not been disturbed (if that's the way you fly). Starting at the crank, work counter-clockwise keeping tension on the belt. So, crank to oil pump, around idler pulley, around camshaft, and behind the tensioner arm/pulley. NOTE: this is for the 2.4l SOHC 4G64 engine

May 18, 2014 | 1995 Eagle Summit

1 Answer

Hellow i have a question .imy girfriend has a honda civic 2006 and she crashed it and the place where she took it to fix it told her that she has to replace her seat belts and that they are 400 $ o

Seat belts keep you from flying out of the windshield and dying. Since they have already absorbed the shock of one accident, no one can guarantee that they will offer the same level of protection next time. And yeah, they're expensive.

Apr 07, 2012 | Honda Civic Cars & Trucks

1 Answer

Timing diagram for both belts

always timing mark at the rear of cam shaft by useing special tools . for crankshaft on gear box housing there is plastic cover remove you can see mark on flywheel . there mark for timing belt tensioner try to keep not too mach tight ( you can press timing belt with your fn). for 1.8 over head camshft there is mark on camshat and camshaft bracket keep two point together for each camsh.then but the chain . for 1.2 engine use special tools rear camsh.with mark on fly wheel

Jun 19, 2011 | Volkswagen Camper Cars & Trucks

1 Answer

Where is the starter located what is it near or next to

located on the backside of the motor next to the fly wheel/drive plate end
standing in front of the car looking at the car ,you are at the front of the engine. you have to go under the car to the other side of the engine.find the belts should be up and over just a bit from the belts
going to keep the car suggest you get a do it yourself book try half priced book store or aotu parts store

Aug 05, 2010 | 1995 Kia Sephia

1 Answer

I cut the Ac on and the timing belt came loose. I am being told the tension pulley is bad? Could this be true?

Sure, the tensioner holds tension on the belt and keeps it from flying off.
I suspect the belt was tightened and this occurred afterward?

Jul 23, 2010 | 1998 Chevrolet Cavalier

1 Answer

How do i replace the timming belt on a 1996 vw glof 2.0

if you havn' t done it before best to get an experienced technician to do it. [critical part, can cause major damage if incorrectly fitted]. before removing belt line up timing mark on crankshaft pulley with arrow on timing belt cover. remove inspection plug on top of gearbox bell housing. v cut away on fly wheel should be lined up with notch on g/box housing. timing mark on inside of camshaft pulley must line up with top of cylinder head surface at front of head. if distributor fitted, remove cap . rotor should be pointing to mark on distributor housing. remove old belt, fit new keeping timing marks in same positions. tension cambelt. should be able to turn belt 90 degrees side ways between cam pulley and intermediate pulley if tension is correct. reset ignition timing on completion.

May 20, 2010 | 1996 Volkswagen Golf

1 Answer

Snow and slush causes the belt to slip off. Belt is on properly and all the tensioners and fly wheels are lined up. Belt never came off in rain or dry conditions, only when there is snow on the road.

Not sure why but the only thing that keep the belt on tight is size and a good tensioner. You may need to replace both the belt and tensioner to fix this condition.
I have seen this condition before on chrysler/dodge vans

Dec 29, 2009 | 1999 Plymouth Voyager

1 Answer

1984 Cadillac Deville Ddiesel

You need to pull the starter out and check the drive gear. If the drive gear is no good you will have to replace the starter. Make sure the cogs on the fly wheel are okay. If the fly wheel is damaged you will have to replace the fly wheel.

Apr 25, 2009 | 1984 Cadillac DeVille

Not finding what you are looking for?
1993 Geo Metro Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Mike Gilbreath

Level 1 Expert

50 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides