Question about Chevrolet Venture
TAKE THE WHEEL AND BRAKES OFF THERE IS AN AXLE NUT IN THE MIDDLE TAKE IT OFF AND THEN THERE ARE 3 BOLTS THAT COME IN FROM THE BACK SIDE REMOVE THEM AND THE BEARING WILL COME OUT (MAY HAVE TO USE A HAMMER THEY DO STICK)
Posted on Oct 14, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: replace front wheel bearings
The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.
On a scale of 1-10 difficulty, Id rate it a strong 7
Posted on Jun 20, 2008
SOURCE: replacing a front wheel bearing
here is a step by step instructions on how to replace your bearing. please copy and paste the link into your browser for an image.
please do not forget to rate and comment about your experience with fixya today.
Removal & Installation
CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during removal. Hold the bolts stationary in the steering knuckles while removing the nuts, then tap the bolts out using a pin punch.
NOTE Use caution when separating the ball joint stud from the steering knuckle, so the ball joint seal does not get cut.
NOTE Do not allow the driveshaft to hang by the inner C/V joint; it must be supported to keep the joint from separating during this operation.
NOTE The cartridge type front wheel bearing used on this vehicle is not transferable to the replacement steering knuckle. If the replacement steering knuckle does not come with a wheel bearing, a new bearing must be installed in the steering knuckle. Installation of the new wheel bearing and hub must be done before installing the steering knuckle on the vehicle.
http://www.chiltonlibrary.com/content/images/32050/images/32050_ptcr_g0035.gif The separation of the ball joint and the knuckle
CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during installation. Install the nuts while holding the bolts stationary in the steering knuckle.
Posted on Apr 17, 2009
SOURCE: replacing front wheel bearing
Posted on Apr 25, 2009
SOURCE: Replacing front wheel bearings
It isn't a particularly hard job but there are a few techniques that you need to know.
I wouldn't recommend you do it yourself but I would recommend you do it under supervision of someone who knows their stuff.
Retensioning the bearings correctly is extremely important.
Posted on Jun 27, 2009
remove the hub and spinle ,tie rod end ,axle nut.ball joint,and seperate from strut and then have new bearing pressed in...or rent a bearing press that works with an impact wrench,but they are a little hard to work with...good luck...lee
Posted on Sep 07, 2009
Tips for a great answer:
Dec 09, 2015 | Kia Cars & Trucks
Nov 06, 2015 | 2002 Kia Rio
Sep 09, 2015 | 2005 Mercury Mariner
Aug 16, 2015 | Honda Cars & Trucks
Aug 03, 2014 | 2002 Mitsubishi Lancer
Feb 22, 2012 | Ford F-250 Cars & Trucks
Apr 09, 2010 | 2003 Ford Explorer Sport Trac
Apr 07, 2010 | 2003 Chevrolet Suburban 1500
Oct 23, 2009 | 2006 Hyundai Sonata
Jul 26, 2008 | 2004 Ford Crown Victoria
Aug 22, 2017 | 1998 Chevrolet Camaro
105 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: