1998 Honda CR-V Logo

Related Topics:

Posted on Oct 14, 2010

How to replace front headlight buble 1998 honda crv

5 Related Answers

Anonymous

  • 5 Answers
  • Posted on Dec 23, 2008

SOURCE: How to change the whole headlight assembly on a 05 Honda CRV

When you raise the hood, look for a Phillips screw that holds the parking lamp in. if it is there remove screw and pull parking lamp toward front of vehicle. If headlamp and side lamp are 1 piece, there should be 2 number 10 mm headed bolts that are vertical, that hold the assembly in. The side lamp will have a stud that holds the light to the fender. You may have to pry it loose. Reverse procedure to install.

Ad

Anonymous

  • 1 Answer
  • Posted on Jan 01, 2009

SOURCE: how to change my headlights on Honda 2005 CRV

easy cheesy! Ive changed mine twice. The headlights are small bulbs. Make sure you get the right one (hi-beam vs low-beam). Unplug connector at back of bulb / headlamp unit, remove rubber weather seal (pops right ot). The bulb is held in with a small wire clip that is hard to get back on but can be done. Its spring loaded. Drop wire clip, turn bulb assya 1/4 turn, and it comes right out. Remove bulb from holder and replace. Reverse steps and VOILA!

satitus

steve titus

  • 277 Answers
  • Posted on Jan 30, 2010

SOURCE: Clock does not work. crv 1998

If it is not the fuse then it is most likely an internal issue with the clock itself. These clocks (and many other models) commonly burn out internally. I offer a very cost effective repair solution. Check it out!
www.autoclockrepair.com

$200 less than the dealer and a lifetime guarantee

Anonymous

  • 1 Answer
  • Posted on Apr 15, 2010

SOURCE: how to replace headlight washer jet for honda crv

how do you replace the headlight water jet on a honda crv

johnjohn2

Johnny Brown

  • 5763 Answers
  • Posted on Apr 21, 2010

SOURCE: replacing cruise control bulb on honda crv 2006

JUST POP SWITCH OUT AND BULB GOES INTO SWITCH USE SMALL SCREW DRIVER TO REMOVE YOU WILL HAVE TO TWIST IT COUNTERCLOCKWISE TO REMOVE, TWIST CLOCKWISE TO INSTALL.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to replace lower ball joint on 1998 Honda CRV?

On a car this old, I would replace the whole lower arm, because the inner bushing is probably worn out, too. Much easier to do, so the cost of the part might be offset by the savings in labor. Just a few nuts and bolts and getting the ball joint to release from the knuckle with a few hammer hits.
1helpful
2answers

Where can i find the routing diagram for the a/c belt on a 1998 Honda CRV

You need the routing diagram for the a/c belt on this 1998 Honda CRV


here is a diagram of all three belts, this one is simple , the ac belt just goes around the pulleys. hope this is helpful good day2_3_2013_8_04_36_pm.gif
0helpful
1answer

1998 Honda CRV Drivers side window(power)

Did you check for power and ground at the window motor connector before you replaced it? Apparently not....
2helpful
1answer

How do you release the headlight retaining clip on 1998 crv

Click HERE to view video of a 2000 CRV bulbe replacement , it is the same.
0helpful
2answers

Install honda crv headlight

Welcome to FixYa.com

Thank you for using FixYa.com, Regards, Lee Davidian

b8680b3.png0526d13.png


Thank You for using FixYa - a 4 THUMBS- UP rating is appreciated for answering your FREE question!!!!!

3helpful
1answer

Hi Honda crv (98) R overheating.

SOUNDS LIKE YOUR THERMOSTAT IS STICKING,REPLACE THERMOSTAT FIRST OVERHEATING WILL DAMAGE ENGINE.IF THAT DOSEN'T WORK HAVE WATER PUMP CHECKED.FANS WON'T TURN ON IF HEAT FROM ENGINE IS NOT FLOWING INTO RAD BECAUSE THEROMOSTAT STUCK CLOSED,OR WATER PUMP FAILING
0helpful
2answers

Honda CRV 98 Radio fuse

The ground wire (usually black) is dirty/defective.
11helpful
2answers

How to change the whole headlight assembly on a 05 Honda CRV

You have to remove the front bumper and grill etc

There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.

Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.
Not finding what you are looking for?

348 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...