Question about 1993 Jeep Wrangler

1 Answer

The whole circuit board on my 1993 jeep wrangler went out. any way to fix it without replacing the whole thing??

Posted by on

  • Richard Scordino Oct 14, 2010

    Which board??? really does not mater....when a board goes, it's gone. Even a difference in solder composition can change the way it works after a "repair"

  • mari36bel Oct 14, 2010

    well all i know is that all the gauges are not working - they were and i went over a speed bump and they stop! help!

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

So you are assuming the board is bad.....Jeep gauge clusters are notorious for problems at the plug behind the board. Sometimes you can get it working just by giving the dash a good whack with your hand right above the gauges.(not kidding) If that works, best thing to do is remove the cluster and spray contact cleaner on the pins and contacts.. In extreme cases you can slightly twist the pins very slightly to make them fit tighter. (last resort).

Posted on Oct 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where's the orifice tube on a 4.0 jeep wrangler? It's a 1999 modle


THE FIX ORIFICE TUBE AND LINE TO EVAPORATOR IS A INTEGRAL PART IN WHICH THE WHOLE LINE TO EVAPORATOR HAS TO BE REPLACED.BECAUSE THE ORIFICE FIX INSIDE IT CANT BE REMOVED THE WHOLE LINE HAS TO BE REPLACED.

Mar 04, 2011 | 1999 Jeep Wrangler

1 Answer

I just bought a 1993 jeep wrangler 4wd. The only thing is the horn isn't working. How can I fix this?


First check that the fuse for the horn is good and if it is you will need to replace the horn relay that is found in the under hood high amp fuse box.

Feb 22, 2011 | 1993 Jeep Wrangler

1 Answer

2004 jeep wrangler SE start circuit will not pull in the starter


Is your starter good? What happens when you try and start the jeep? Does the starter just spin? If so you have a bad pull in winding on your starter. You can just get that fixed or get a whole new starter.

Jun 20, 2010 | 2004 Jeep Wrangler

1 Answer

I have a 93 Jeep wrangler the slave cylinder went out I need step by step instructions on how to replace it please make the instructions idiot proof


u have to pull trans back or out to do this,,if u want step by step,,get a haynes repair book on ur jeep;;auto zone or advance sell them,,about twenty dollars,,it is not a easy fix,,

May 24, 2010 | 1993 Jeep Wrangler

1 Answer

I have a 1993 jeep wrangler soft top with half doors i need to know how to remove the windows from the doors


it has velcro at bottom of the window, pull it loose and the whole window frame will come off

May 21, 2010 | 1993 Jeep Wrangler

1 Answer

Where is the water pump located on a 1993 jeep wrangler? how involved is replacing it?


Its the big metal thing that the raidator fan is attached to. Its not hard to do, but you need to know what you are doing. Pay a repair shop to do it right.

May 14, 2010 | 1993 Jeep Wrangler

1 Answer

1993 Jeep Wrangler Fuse #12 melted and that's the one that goes to the heater and A/C do i replace the fuse or get professional help?


Well you can try and replace the fuse, but it might burn the vehicle to the ground or might not. If the fuse has melted then I would guess that there is not much voltage going through that circuit, since if it was amps the fuse would have simply blown.
If this is the case then replacing the fuse won't help, go to a good shop and tell them all you can. To find a good shop ask around to friends and see where they have gone or go and talk to the shop and see if they give you straight answers or a bunch of things you don't understadn. I find a good shop can usually explain things clearly and simply without insulting your intelligence.
Best of luck

Jun 22, 2009 | 1993 Jeep Wrangler

2 Answers

Hard to get into reverse


try shifting in to first and then reverse. reverse might be worn out. you can have that gear replaced without replacing the whole transmission.

Jun 19, 2009 | 1998 Jeep Wrangler

2 Answers

My 93 jeep wrangler speedometer stopped working on day it was rainin out and hasnt worked since any idea why and how to fix


Check the connection to the speed sensor gear. It will be a cable plugged into the output shaft on the top of the transfer case (behind the transmission). It is possible that it became disconnected or has a broken wire.

Apr 09, 2009 | 1993 Jeep Wrangler

2 Answers

Second tinme throw out bearing has to be replaced.


This is a weird one. Unless there is a TSB on bad bearings from the dealer, the only thing I could GUESS is a bad pressure plate, but you said you are replacing the whole thing.

Nov 22, 2008 | 2008 Jeep Wrangler

Not finding what you are looking for?
1993 Jeep Wrangler Logo

Related Topics:

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...