Question about 1992 Acura Legend

1 Answer

I have repair my cooling sytem replaced from top to bottom new radiator,water pump, timebelt, thermostat, and new switch in radiator. but my fan are not running need help why???

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

These cars have been known to have bad radiator fan relays/condensor fan relay. they're located on drivers side,in small relay box attached to radiatortop support bracket.that relay is also common with several others on car so you could `technically swap out with another identical relay from car for testing purposes.anyways.

Posted on Oct 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Overheating 97 Lincon Town car


Connie, Were the radiator,water pump and thermostat replaced to try and fix the over heat issue or as maintenance. Engine overheating can be caused by a lot of things, Leak in cooling system, air in system, bad rad. cap, slipping belt, faulty thermostat or installed upside down, faulty water pump, plugged radiator (inside/outside), collapsing rad hose, faulty cooling fan, leaking head gasket, sludge plugging engine water passages, poorly tuned engine, etc..
Take into a good shop for diagnoses and estimate for repair. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Troubleshoot an Overheating Engine
Steve Litt Overheating Guide
Diagnose Engine Overheating Auto Repair Help
How to Troubleshoot an Overheating Engine DoItYourself com

Jul 21, 2016 | Cars & Trucks

3 Answers

Car overheating


Two things to check:

1. Make sure you do not have an air bubble in your cooling system. Easiest way is to park facing uphill and let the car cool off. Remove the radiator cap, start the car and let run until the thermostat opens. If there are air bubbles in the cooling system the should be forced out. Top off fluid.
2. Are you sure that the cooling fan is running? When the car is getting hot, open the hood and make sure the radiator fan is actually turning.

Aug 31, 2015 | 2001 Pontiac Grand Am SE

2 Answers

Have a 02 trail blazer blew rad apart replace


check thermostat in boiling water make sure it opens. make sure it is not fitted up side down, check the radiator pressure with a gauge there may be a leaking head gasket. also check the relief valve on the radiator cap.

Sep 21, 2014 | 2002 Chevrolet TrailBlazer

1 Answer

2004 Jetta 4 1.6 Overheating problem. i noted that the radiator fan did nit switch on. Also noted that the top hose to radiator was warm and botttom hose was "cold". I changed the fan, the heat...


remove cooling flute and thermostat fit1/3 off radiator cleaner with fresh water top up 1/3 more in and 1/3 two days later drive for 1 week and flush your system fit new thermostat new radiator cup and antifreeze .notes radiator blockage after removing the thermostat is,when engine is hot top hose expand and is hotter then the bottom hose notes when the fans engage.

Sep 02, 2012 | Cars & Trucks

1 Answer

01 freelander condenser/cooling fan donot switch off


DII thermostat works. At idle it pretty much redirects hot coolant into the water pump. Dumb system that works of coolant pressure and not temperature.bad thermostat or water pump or cloged sytem your vehicle thermostat is different then most vehicles your vehicle thinks its over heating when its not i would start by changeing the thermostat and haveing a radiator flush done ive learned something new today happy holidays god bless

Dec 15, 2010 | 2002 Land Rover Freelander

2 Answers

Car overheats


The problem of over-heating could be due to one or all of these defective parts:
(i) thermostat
(ii) radiator
(iii) fan relay
(iv) fan switch
(v) water temperature sensor.
In your case, I suspect that your radiator probably is clogged, so needing replacement.

To Replace the radiator:
a. allow the engine to cool.
b. place a suitable container under the radiator, and drain it out by turning backward the wing-nut under it.
c. open the radiator cap to allow atmospheric air to further push down the coolant.
d. with a piece of pliers, depress the top clamp holding the radiator hose. Do the same for the lower radiator hose.
e. remove from the bottom of the radiator and plug wth suitable bolts, the two transmission fluid rubber lines.
f. with a 10-mm socket and wrench remove the two bolts holding the radiator to the front frame.
g. depress the electrical plug at the bottom of the radiator. Remove its thermo switch at the bottom left hand side of the radiator. (replace with new if changing to new radiator) Also notice two rubber cups at bottom of radiator.
i, installation of the new radiator is reverse of removal. Refill radiator with new coolant.

To replace thermostat:
a. disconnect the negative terminal of the battery.
b. drain the coolant into a container, as
explanied above.
c. remove the upper radiator hose from the thermostat housing on the engine block.
d. remove the two bolts from the thermostat housing. Please note the way it was bolted to the engine. Clean its housing and seating areas.
e. fit a new o-ring to the thermostat, and replace with a new thermostat.
f. tighten its bolts to 14-12-foot pounds.
g. Replace the top and bottom hoses back.
i. refill with new coolant.

To replace the fan relays:
a. open the hood.
b. disconnect the negative battery terminal.
c. locate the meduim-size black plastic box on the driver's side fender. This is where the fan relays are. Look inside the cover of the medium-size plastic box to see the fan relay positions.
d. gently and firmly pull out each fan relay. Replace with new ones as needed.

To replace the water temperature sensor:
a. this is bolted to the top of thermostat housing.
b. unplug it from it location.
c. use a 14-mm deep socket to remove the temperature sensor. Replacement is reverse of removal.

Dec 09, 2009 | 1995 Toyota Camry

1 Answer

94 toyota 4 runner overheating


The engine is kept cool by a liquid circulating through the engine to a radiator. In the radiator, the liquid is cooled by air passing through the radiator tubes. The coolant is circulated by a rotating water pump driven by the engine crankshaft. The complete engine cooling system consists of a radiator, recovery system, cooling fan, thermostat, water pump and serpentine belt.

Check the coolant level in the recovery bottle or surge tank, usually mounted on the inner fender. With the engine cold, the coolant level should be at the FULL COLD or between the FULL HOT and ADD level. With the engine at normal operating temperature, the coolant level should be at the FULL HOT or HOT mark. Only add coolant to the recovery bottle or surge tank as necessary to bring the system up to a proper level. On any vehicle that is not equipped with a coolant recovery bottle or surge tank, the level must be checked by removing the radiator cap. This should only be done when the cooling system has had time to sufficiently cool after the engine has been run. The coolant level should be within 2 in. (51mm) of the base of the radiator filler neck. If necessary, coolant can then be added directly to the radiator.

While you are checking the coolant level, check the radiator cap for a worn or cracked gasket. If the cap doesn't seal properly, fluid will be lost and the engine will overheat.

Worn caps should be replaced with a new one.

Periodically clean any debris; leaves, paper, insects, etc. from the radiator fins. Pick the large pieces off by hand. The smaller pieces can be washed away with water pressure from a hose.

Carefully straighten any bent radiator fins with a pair of needle nose pliers. Be careful, the fins are very soft. Don't wiggle the fins back and forth too much. Straighten them once and try not move them again. It is recommended that the radiator be cleaned and flushed of sludge and any rust build-up once a year. If this has not been administered within the stated time, this may be why your vehicle is overheating at this time. Have the Radiator flushed asap if this is the case.

Now, if the coolant level is proper and, the cap is in fair or good condition, i would advise to move in the direction of the cooling fans and sensors as well. These fans are vital to the cooling process as well. The cooling fans must cycle in intervals to keep the coolant cool during stop and go driving or, long idle. They are also very important during the operational period of the AC during travel as well. i recommend inspecting the cooling fans while the engine is running. they should cycle during the running period. if thsi is not the case, you will need to test the operational value of these devices. The test procedure follows below


TESTING


1. If the fan doesn't operate, disconnect the fan and apply voltage across the fan terminals. If the fan still doesn't run, it needs a new motor.

2. If the fan runs, with the jumpers but not when connected, the fan relay is the most likely problem.

3. If fan operates but a high current draw is suspected continue with the following ammeter TESTING.

4. Disconnect the electrical connector from the cooling fan.

5. Using an ammeter and jumper wires, connect the fan motor in series with the battery and ammeter. With the fan running, check the ammeter reading, it should be 3.4-5.0 amps; if not, replace the motor.

6. Reconnect the fan's electrical connector. Start the engine, allow it to reach temperatures above 194°F and confirm that the fan runs. If the fan doesn't run, replace the temperature switch.



Ok, Now we will move on to the next possible issue. The water pump. ok, due to the fact that your pump is driven by the drive belt, you will need to start the engine and listen for bad bearing, using a mechanic's Stethoscope or rubber tubing.

* Place the stethoscope or hose on the bearing or pump shaft.
* If a louder than normal noise is heard, the bearing is defective.

Replace the pump in this case.

You will also notice leakage around the pump housing if the seal has failed as well. this will strain the impeller and, ruin the pump.

Now. the last area of concern will be the thermostat. this is the most common issue that will inflict overheating in many vehicles. The thermostat is used to control the flow of engine coolant. When the engine is cold, the thermostat is closed to prevent coolant from circulating through the engine. As the engine begins to warm up, the thermostat opens to allow the coolant to flow through the radiator and cool the engine to its normal operating temperature. Fuel economy and engine durability is increased when operated at normal operating temperature.


There are several ways to test the opening temperature of a thermostat.

One method does not require that the thermostat be removed from the engine.

* Remove the radiator pressure cap from a cool radiator and insert a thermometer into the coolant.
* Start the engine and let it warm up. Watch the thermometer and the surface of the coolant.
* When the coolant begins to flow, this indicates the thermostat has started to open.
* The reading on the thermometer indicates the opening temperature of the thermostat.
* If the engine is cold and coolant circulates, this indicates the thermostat is stuck open and must be replaced.

The other way to test a thermostat is to remove it.

* Suspend the thermostat completely submerged in a small container of water so it does not touch the bottom.
* Place a thermometer in the water so it does not touch the container and only measures water temperature.
* Heat the water.
* When the thermostat valve barely begins to open, read the thermometer. This is the opening temperature of this particular thermostat.
* If the valve stays open after the thermostat is removed from the water, the thermostat is defective and must be replaced.
* Several types of commercial testers are available. When using such a tester, be sure to follow the manufacturer's instructions.
* Markings on the thermostat normally indicate which end should face toward the radiator. Regardless of the markings, the sensored end must always be installed toward the engine.
* When replacing the thermostat, also replace the gasket that seals the thermostat in place and is positioned between the water outlet casting and the engine block.

* Generally, these gaskets are made of a composition fiber material and are die-cut to match the thermostat opening and mounting bolt configuration of the water outlet.
* Thermostat gaskets generally come with or without an adhesive backing. The adhesive backing of gaskets holds the thermostat securely centered in the mounting flange, leaving both hands of the technician free to align and bolt the thermostat securely in place.

Nov 25, 2009 | 1994 Toyota 4Runner

1 Answer

Overheating 97 V6 pontiac grand am


1 Inspect Cooling System Mix Coolant level low or flow is restricted. grey_line.gif 2 Inspect Belt Incorrectly routed, adjusted, tensioned, missing, or worn water pump belt(s). grey_line.gif 3 Inspect Oil Pan Gasket - Performance Ruptured, cracked or leaking radiator hose. grey_line.gif 4 Inspect Radiator Cap Worn or damaged radiator cap grey_line.gif 5 Inspect Thermostat Thermostat stuck closed grey_line.gif 6 Inspect Fan Blade Broken, missing, or defective fan blade(s). grey_line.gif 8 Inspect Water Pump Damaged, worn or leaking water pump. grey_line.gif 9 Inspect Intake Manifold Plenum - Perform Leaking water pump gasket. grey_line.gif 10 Inspect Cooling Fan Control Faulty cooling fan control or circuit. grey_line.gif 11 Inspect Cooling Fan Switch - Radiator Faulty radiator cooling fan switch or circuit. grey_line.gif 12 Inspect Engine Temperature Sensor Faulty engine temperature sensor or circuit. grey_line.gif 13 Inspect Temperature Switch Damaged or faulty temperature switch or temperature switch circuit. grey_line.gif 14 Inspect Fan Clutch Worn, loose or faulty fan clutch. grey_line.gif 15 Inspect Ported Vacuum Switch Damaged, leaking, or faulty ported vacuum switch. grey_line.gif 16 Inspect Radiator Obstructed radiator core or radiator cooling fins. grey_line.gif 17 Inspect Head Gasket - Performance Head gasket leaking coolant into cylinders

Dec 01, 2008 | 1997 Pontiac Grand Am

1 Answer

Car is overheating


2 Inspect Belt Incorrectly routed, adjusted, tensioned, missing, or worn water pump belt(s). grey_line.gif 3 Inspect Oil Pan Gasket - Performance Ruptured, cracked or leaking radiator hose. grey_line.gif 4 Inspect Radiator Cap Worn or damaged radiator cap grey_line.gif 5 Inspect Thermostat Thermostat stuck closed grey_line.gif 6 Inspect Fan Blade Broken, missing, or defective fan blade(s). grey_line.gif 8 Inspect Water Pump Damaged, worn or leaking water pump. grey_line.gif 9 Inspect Intake Manifold Plenum - Perform Leaking water pump gasket. grey_line.gif 10 Inspect Cooling Fan Control Faulty cooling fan control or circuit. grey_line.gif 11 Inspect Cooling Fan Switch - Radiator Faulty radiator cooling fan switch or circuit. grey_line.gif 12 Inspect Engine Temperature Sensor Faulty engine temperature sensor or circuit. grey_line.gif 13 Inspect Temperature Switch Damaged or faulty temperature switch or temperature switch circuit. grey_line.gif 14 Inspect Fan Clutch Worn, loose or faulty fan clutch. grey_line.gif 15 Inspect Ported Vacuum Switch Damaged, leaking, or faulty ported vacuum switch. grey_line.gif 16 Inspect Radiator Obstructed radiator core or radiator cooling fins. grey_line.gif 17 Inspect Head Gasket - Performance Head gasket leaking coolant into cylinders here is a list of things to check Shaun

Nov 17, 2008 | 2000 Cadillac DeVille

Not finding what you are looking for?
1992 Acura Legend Logo

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...