Question about 1997 Chevrolet Blazer

1 Answer

Installed starter......still won't turn over - 1997 Chevrolet Blazer

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

You could have a bad battery cable

Posted on Oct 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1988 2wd pickup and the starter won't


starter wont turn or engages the flext plate,flywheel and still wont turn engine over?if this is the case you have a seized up motor,but if it doesnt even click check signal wire from ignition switch for power when you turn the key to crank.if no power your ignition switch,park/neutral safety switch(clutch switch if manual trans) or wrongly installed wired could be the problem.

Jul 18, 2013 | Cars & Trucks

2 Answers

I try to start my Lincoln town car and when I turn the ignition on the electrical battery system goes down but won't turn over. I have installed a new car battery


You would need to take a meter or test light and check for power after the battery. You could have a bad connection inside one of the cables.
There should be 12 volts at the battery post and at the cable end on the starter. Also be sure and check the ground connections.

Jan 30, 2013 | Lincoln Town Car Cars & Trucks

2 Answers

My 1973 porsche 914 had a new starter installed but when you turn the ignition to start it won't engage. Any clues as to what it could be?


I'm probably stating the obvious but I presume you've cleaned and checked all the wire connections. If you haven't yet done so, it might be a good time to install the hot-start relay kit that AutoAtlanta sells for these cars. That may solve the problem and will prevent the future non-starts when the engine is hot. Also, ask the same question on the 914 Club or World forum and you'll get some real expert advice.

Dec 31, 2012 | 1973 Porsche 914

1 Answer

Disconnected battery and now won't start


Won't start as in no rotation of the starter motor and no clicking sound? Or starter turns slowly with the engine? Or the starter and engines turns normally but will not start? Or starter turns normally but engine will not turn?

Oct 15, 2012 | 2004 Jeep Grand Cherokee

1 Answer

Installed new starter still wont start


Well, I guess the starter was not the problem then. Please review the following articles. You may find them helpful.

What Else Could Be Wrong?

My Car Won't Turn Over

Jan 08, 2012 | 2002 Ford Taurus

1 Answer

Car won't start. New battery installed recently. Only clicks when trying to start.


one single click any time you turn the key usually indicates a bad solenoid on the starter. A new starter will typical get you going.

A series of rapid clicks when you try to start usually indicates a weak battery. There could also be a bad connection at the terminals on the battery or even a poor connection at the starter.

If you get a single click and everything goes dead for a couple of seconds than you definitely have a bad connection at the battery.

Let me know what you find or if you have any questions.

Dec 28, 2011 | 2007 Chevrolet Tahoe

1 Answer

HOW TO INSTALL STARTER ON A 97 FORD THUNDERBIRD


I'm not sure that your starter is in good condition .You have to pull your starter out from engine .
Ensure the safety dental starter and the engine .
If you find that the dental starter Moving north and right .
You have to replace the starter .
good luck , and let me know .............

Nov 02, 2011 | Cars & Trucks

3 Answers

REMOVED ALARM -STARTER WON'T ENGAGE-NO POWER TO ENGINE


When you removed the alarm unit you cut the line to the Starter kill switch that was installed. Remove the starter kill switch which is most likely located under the dash spliced into the ignition wiring harness.

Jul 08, 2011 | 1999 Dodge Intrepid

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...