Question about 1993 Jeep Grand Cherokee

4 Answers

93 jeep grand cherokee, cruise control

I just purchased a grand cherokee and I cannot get the cruise control to work, can you tell me where the fuse or relay is in the vehicle..Thanks

Posted by on

  • 2 more comments 
  • Anonymous Mar 14, 2014

    fuel pump relay control circuit

  • Anonymous Mar 25, 2014

    My original question was getting a 2012 maintain/ repair manual,I have maintained all my vehicles for 30 years,to date I can not find this manual . Thx

  • Anonymous Mar 30, 2014

    Cruise control stopped working on my 2001

  • Anonymous Mar 30, 2014

    Where is it located

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

First, there is no 'fuse' identified in either of the Haynes or Chilton's manuals. I've looked. There could be a 'fuse link' somewhere in the line, as it's incomprehensible the folks at Chrysler would design this vehicle with a fire hazard built into it like that, no fuse or fuse link or relay known, but the mythological 'fuse' referenced in the troubleshooting section of both manuals.

In any case, if the vacuum line appears to not leak when you open it and **** on the line going to the rest of the vacuum system, or pull vacuum on it with a small handheld vacuum pump, and it doesn't leak, it then becomes an 'electrical' issue.

mine worked flawlessly for a a long time, and suddenly without warning 'died' and wouldn't work one day. It didn't go out on the job, in other words.

last but not least, references to the brake switch are made, but if the brake lights work, that seems to eliminate the brake switch as a possibility.

sounds expensive taking it to a Jeep dealership, but if you have a reputable one (hahahahahahah!) in your vicinity, they might zero in on it fast and fix it cheap, then again, they may not. Driving this vehicle without cruise control across country isn't so bad, but it requires a lot of foot wedging near the pedal, to get that done without having a very tired leg over time.

Posted on Jun 14, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Mine turned out to be the brake switch. I could get it to work by tapping the back of the brake pedal with my foot, but it wasn't too reliable that way. The brake lights always worked.

Posted on Aug 04, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Just in case you haven't got this fixed already, I just noticed on my 93, the cable from the vacuum control, (the cone shaped device on the passenger side near the coolant overflow ) was sitting against the tubes from the ac compressor, it had started to melt from me using the ac, if it melts through I am not sure if it would cause a vac leak, but if it did, you would only be able to detect it with the cruise on, not easy to check with the vehicle parked. I used a couple of cable ties to secure it away from the tube..not sure if you can tape around it to fix if it has melted.
just thought I would throw it into the mix.
j

Posted on Aug 13, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Maybe you can read some literature before of your visit to the Chrysler Deal; I have this doc in spanish language, but is easy understood...
Cruise Control System - Inspection and Diagnostic (spanish)

Good luck!!!

Posted on Aug 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cruise control doesn't work 1995 jeep grand Cherokee laredo


being a 95 locate cruise control unit under hood & check for broking vacume hose
and replace make sure fuse is active

May 02, 2011 | 1995 Jeep Grand Cherokee

1 Answer

I wanted to know what fuse 8 in the 1995 jeep grand cherokee controls?


We assuming that you are talking about Fuse Block Compartment (inside the car) and the Fuse 8 15AMP work for Fused Battery-Memory Circuits

Additional details could fin in the Jeep-ZJ-Secc-8W-Wiring-Diagrams; keep in mind that you have a nice SUV, I have the same but '93 Grand Cherokee Limited 5.2L V8.

Good luck.

Mar 07, 2011 | 1995 Jeep Cherokee

1 Answer

My Jeep Grand Loredo 2004 cruise control went out


Check the vacuum hoses it is easy to notice if one is missing or not. If that doesn't work, I'd try the cruise control switch. Hope this helps

Apr 05, 2010 | 2004 Jeep Grand Cherokee

1 Answer

Cruise control no go when button is pushed


I press the control switch on my 1999 Jeep cherokee. the cruise light doesn't come on and the cruise does not engage. Please offer a solution.

Nov 14, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Cruise control just quit working


Check fuses/relays and make sure they are all good; if so check the electrical wiring/connectors in the dash. Jeeps are notorious for loose wires in the dash.

Sep 01, 2009 | 1995 Jeep Grand Cherokee

1 Answer

WHERE IS THE CRUISE CONTROL FUSE FOR A 1996 JEEP GRAND CHEROKEE?


According to my wiring diagram there is no dedicated fuse for cruise.The cruis is tied into the powertrain control module.

Aug 05, 2009 | 1996 Jeep Grand Cherokee

3 Answers

2003 jeep grand cherokee cruise control not working.


Ok, the '03 Jeep Grand Cherokee uses a small vacuum line to control the servos. Since your light comes on, it's obviously getting power. 9 out of 10 times it's the vacuum hose.
Pop the hood and look on the passenger side towards the back for the engine coolant reservoir. It's most likely underneath it so you may have to remove the res. Check the vacuum hose and all vac. connections then check the electrical connections. If that's not the problem, check the cruise control connection to the throttle linkage.
If that still doesn't do it, you may need use scan tools and diagnostic procedures that are out of the scope of home mechanics.
Wish ya luck!

Jun 18, 2009 | 2003 Jeep Grand Cherokee

1 Answer

Cruise not working is there a fuse for 2000 jeep grand cherokee?


Look on the drivers side of the intake manifold to see if the vacuum line fell off. It will be a 90 degree elbow coming down from the firewall area.

May 01, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Cruise control not working


Review this information about Jeep-WJ-Cherokee-Service-Manual-PDF-08W-Diagrama-de-Cableado (Wiring Diagrams / Section 8W Page 181 (8W 33-1)

Is in spanish, but the graphics can help you.

Good luck!!!

May 01, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

920 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...