Question about 2002 GMC Savana

1 Answer

How do I reprogram the keyless entry remote for a 2002 GMC Savana?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Expert
  • 87 Answers

Take it to the garage

Posted on Oct 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I went through programing as far as lock recycling but wont go any further


Remote Transmitter Programming NOTE: All keyless entry remote transmitters must be programmed at the same time.
NOTE: Programming (or reprogramming) the keyless entry remote transmitters into the central security module can be accomplished using a diagnostic tool or by carrying out the following steps.
  1. Turn the ignition switch from OFF to RUN eight times within 10 seconds, ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after Step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the doors will lock and unlock one last time to confirm.

Mar 18, 2016 | 2004 Ford F150

1 Answer

Bought a used keyless entry remote key fob, how do I reprogram it to a 2008 suzuki sx4?


the operators guide covers this.
lost that? (in the glove box is was)

Jul 02, 2014 | 2008 Suzuki SX4

1 Answer

Remote keyless entry 2002 pt cruiser


Hit and miss, they may need reprogramming to your key. Check that there are no loose wires around fuse box, relays and module. Its a known problem with cruiser (just some cars). There is lots about this on net, one guy just hits his dash and it works again, another guy opens hood and fault clears for a spell.

Apr 06, 2014 | 2002 Chrysler PT Cruiser

1 Answer

Tailgate on a 2002 trailblazer will not open. unlock button wont let it open. what fuse do I need to check or do I open from inside?


  • There was a Technical Service Bulletin concerning this.

  • Bulletin No.: 03-08-52-002
  • Date: March 27, 2003

  • Technical - Subject:
  • Remote Keyless Entry Inoperative (Reprogram Liftgate Module)
  • Models:
  • 2002-2003 Chevrolet TrailBlazer, TrailBlazer EXT
  • 2002-2003 GMC Envoy, Envoy XL
  • 2002-2003 Oldsmobile Bravada
  • Condition
  • Some customers may comment that the Remote Keyless Entry (RKE) is inoperative at times.

  • Cause
  • An anomaly has been identified with the software in the Liftgate Module (RKE functions). The Liftgate Module software is affected when the temperature is approximately 40°C (104°F).

  • Correction
  • Using normal SPS reprogramming procedures, reprogram the LGM Liftgate module. The information was released on TIS version 2.75 or newer broadcast in March 2003.

  • There is a fuse block under the rear seat on the drivers side. Fuse # 3 and # ^ are the ones you will check for the Lift Gate.
  • Often the problem can be in the harness going to the module.
  • Sometimes the module needs replaced and then reprogrammed.
  • Here is a copy of your owners manual for free http://www.extendedgmwarranty.com/owners-manual/chevrolet/2002-Chevrolet-TrailBlazer.pdf
  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.
Regards, Tony

Oct 01, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Keyless entry blinks dome light and does nothing else


The remote is fine - your problem is the lock actuators in the doors. They're a bit of a pain to replace - so, you may want to have a professional do it.

May 03, 2009 | Dodge Dakota Cars & Trucks

2 Answers

Reprogram a keyless entry remote


Hello
this is how to program the remotes/keyless entry

How
  • Obtain all remote transmitters
  • enter the 5 digit permanent code into the keyless entry pad on the drivers door
  • Press the 1-2 switch on the keyless entry pad
  • Within 5 seconds
  • Press any button on the first remote transmitter
  • The doors should open then lock
  • Within 5 seconds
  • press any button on the second & third remote
  • within 5 seconds for each remote
  • to exit programming
  • simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds
NOTE
The 5 digit permanent code is located in one of the following places
  1. On the owners warranty card
  2. On the label on the inside the trunk/ boot
  3. On the owners code card
  4. On the centrel locking control module located in the drivers door
  5. In the PCM ford can get this for about $25.00
I hope this help
Regards Paul
www.limotec.co.uk

Jan 13, 2009 | 1995 Lincoln Town Car

1 Answer

Keyless entry remote doesn't work with old or new batery. If sensor is bad where is sensor and how do you know if sensor is prolem with keyless remote.


I had the same problem. Went to dealer who said it probably needed to be reprogrammed (around $45-50). Paid for premium assistance with FixYA. Ginko gave me the procedure to reprogram my remotes. It was very easy and worked great. Now both of my remotes are working and it only cost me $9.99.

JOECOV

Jul 29, 2008 | 1999 Buick Century

Not finding what you are looking for?
2002 GMC Savana Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...