Question about 1995 Oldsmobile Cutlass Ciera

1 Answer

Location of ignition control box - 1995 Oldsmobile Cutlass Ciera

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 6,826 Answers

Ignition Module 2.2L ENGINE

  1. Disconnect the negative battery cable.
  2. Raise and support the car.
  3. Remove the ignition coil assembly from the engine. Disconnect the coils from the assembly.
  4. Remove the module from the assembly plate. To install:
  5. Install the new module to the plate.
  6. Install the coils to the assembly, and install the coil assembly on the engine.
  7. Lower the car. Connect the negative battery cable, then reset the clock, radio and any other accessories.
2.5L, 2.8L, 3.1L (VIN T) AND 3.8L ENGINES
  1. Disconnect the negative battery cable.
  2. Remove the DIS assembly from the engine.
  3. Remove the coils from the assembly.
  4. Remove DIS module from the assembly plate. To install:
  5. Install the DIS module to the assembly plate.
  6. Install the coils to the assembly.
  7. Install the DIS assembly to the engine.
  8. Connect the negative battery cable, then reset the clock, radio and any other accessories.
  9. On 3.1L engine perform the idle learn procedure.
3.1L (VIN M) ENGINE
  1. Disconnect the negative battery cable.
  2. Remove the 6-way, 3-way and 2-way connectors at the ignition control module.
  3. Remove the plug wires from the coil assembly.
  4. Disconnect the 6 screws that secure the coil assemblies to the ICM.
  5. Remove the nuts and washers securing the ICM assembly to the bracket and remove the ICM. To install:
  6. Install the coils to the ICM installing the 6 screws.
  7. Tighten the screws to 40 inch lbs. (4-5 Nm).
  8. Install the nuts and washers securing the assembly to the bracket and torque them to 70 inch lbs. (8 Nm).
  9. Engage the 2, 3, and 6 way connectors to the ICM.
  10. Connect the negative battery cable, then reset the clock, radio and any other accessories.
Crankshaft Position Sensor (CKP) 2.2L ENGINE
  1. Disconnect the negative battery cable.
  2. Raise the car and support.
  3. Disconnect the harness at the sensor.
  4. Remove the bolt to the sensor.
  5. Remove the sensor from the engine. To install:
  6. Inspect the O-ring and replace if needed. Lubricate the O-ring with engine oil.
  7. Install the sensor to the block.
  8. Insert the bolt and tighten to 71 inch lbs. (8 Nm).
  9. Engage the harness on the sensor.
  10. Lower the car, Connect the negative battery cable, then reset the clock, radio and any other accessories.
2.5L, 2.8L, 3.1L (VIN T) AND 3.8L ENGINES
  1. Disconnect the negative battery cable.
  2. Disconnect crankshaft sensor electrical connector.
  3. Remove the crankshaft sensor attaching bolt, then remove the crankshaft sensor from the vehicle. To install:
  4. Inspect the sensor O-ring for wear, cracks or leakage. Replace as necessary. Lubricate the new O-ring with engine oil prior to installation.
  5. Install the sensor into the hole in the engine block and install retaining bolt.
  6. Engage the electrical connector.
  7. Connect the negative battery cable, then reset the clock, radio and any other accessories.
  8. On 3.1L engine perform the idle learn procedure.
3.1L (VIN-M) ENGINE WITH 3X CKP NOTE: On cars equipped with manual transaxles, the CKP is easily accessed from beneath the engine. For automatic transaxles, the rack and pinion heat shield and the converter intermediate exhaust assembly must be removed.
  1. Disconnect the negative battery cable.
  2. Unplug the sensor connector.
  3. Remove the sensor bolts and the sensor from the engine. Fig. 3: 3X CKP mounting on 3.1L Vin-M location of ignition control box - 86812067.gif

  4. Inspect the O-ring and replace if needed. This is always advisable anyway. To install:
  5. Install the sensor to the engine, tighten the mounting bolt to 88 inch lbs. (10 Nm).
  6. Insert the connector to the sensor, then connect the negative battery cable.
  7. Reset the clock, radio and any other accessories.
3.1L (VIN-M) ENGINE WITH 24X CKP
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley. Fig. 4: 24X CKP mounting 3.1L Vin-M 86812066.gif

  3. Raise the car on a hoist.
  4. Remove the crankshaft harmonic balancer retaining bolt. Use tool J-38197 or equivalent. Fig. 5: Special tool to remove the balancer

  5. Unplug the crankshaft sensor connector.
  6. Remove the 2 sensor mounting bolts, remove the sensor. To install:
  7. Connect the sensor with the 2 mounting bolts. Torque the bolts to 8 ft. lbs. (10 Nm).
  8. Reattach the sensor connector.
  9. Install the balancer on the crankshaft.
  10. Apply thread sealer GM# 1052080 or equivalent to the threads of the balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm).
  11. Lower the car.
  12. Install the serpentine belt.
  13. Connect the negative battery cable, then reset the clock, radio and any other accessories.
Camshaft Position Sensor 3.1L ENGINE (VIN M)
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt.
  3. Remove the power steering pump.
  4. Unplug the connector to the sensor. Fig. 6: Camshaft sensor mounting location on 3.1L engine - VIN M 86812070.gif

  5. Remove the mounting bolt for the sensor, and remove the sensor. To install:
  6. Install the camshaft sensor.
  7. Insert the bolt, tighten down to 8 ft. lbs. (10 Nm).
  8. Insert the electrical connector to the sensor.
  9. Install the power steering pump, and the serpentine belt.
  10. Connect the negative battery cable, then reset the clock, radio and any other accessories. Fig. 7: Conventional ignition system function
    Fig. 8: Distributorless ignition system function 86812073.gif next.gif

Posted on Oct 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Factory alarm wont turn off on a 2001 Chevrolet monte Carlo. Making honk go off till it drains battery.


Try shutting it off with the door key . Lock and unlock the drivers door with it.

Nov 06, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

Saturn 2000 SL: won't start


The ignition control module ( Body Control Module ) is located above the glove box, you'll need to remove it , and its right there.

Sep 20, 2014 | 2000 Saturn SL

1 Answer

Location ignition module


If you're asking about the ECM (Engine Control Module) it's under the dash behind the glove box.

Jul 09, 2014 | 1989 Cadillac Sedan DeVille

1 Answer

99 mercury mystique icm location 4cyl.


The ignition control module on your car is located right on top of the engine. Follow your spark plug wires up to where they all plug in to a small black box often referred to as the ignition coil. Thats it. The ignition control module is integrated into the coil on this car. Hope this helped.

Aug 15, 2012 | 1999 Mercury Mystique

1 Answer

Where is the ignition fuse located


Check with your owner's manual for fuse box location. Many car makers have an imprint on the bottom of the fuse box cover stating which each bank controls.

Apr 30, 2012 | 1995 Kia Sephia

3 Answers

I need to disable my alarm on a 1997 bmw 528i.


Now im not sure since the manual says your model has the same alarm system as the 328i and on the 328i you can remove the module to disable by doing the following. you can unplug the control module. It is located under the glove box. Climb under the dash on the passenger side and remove a few screws on the trim panel under the glove box. Theres a black control module with a green connector. There should be a lock tab on the connector. press the lock tab and pull out the connector. The alarm should now be disabled. But if it has the special transponder key this may not work.
But if the only reason you want to disable it is because of the motion sensor setting of the alarm for no reason there is a solution for this. To disable the motion sensor, hit the lock button to arm, then hit lock button again within four seconds to disable motion sensor. Red light on rearview mirror should flash four times, then pause, then start flashing on regular intervals. this is most likely the reason if your having the issue where the alarm goes off every 20 minutes.
If you want to completely remove it below is a wiring diagram taken from the manual for you alarm system.
this is from the manual its the alarm wiring diagram.
Battery Constant 12v Positive Wire ( ): Red/White or RedBattery Constant 12v Positive Wire Location: Ignition Switch Harness
Starter Positive Wire ( ): Black/Yellow or Black
Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire ( ): Green
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire ( ): Purple/White or Purple
Second Ignition Positive Wire Location: Ignition Switch Harness
Parking Light Positive Wire ( ): Gray/Purple and Gray/Yellow. Use Both Wires. This vehicle has a dual parking light system that will require 2 extra relays.
Parking Light Positive Wire Location: At Headlight Switch
Power Door Lock Positive Wire ( ): White/Red
Power Door Lock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Power Door Unlock Positive Wire ( ): Blue/Red
Power Door Unlock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Door Trigger Negative Wire (-): Brown/Gray
Door Trigger Negative Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Domelight Supervision Wire: Turns On With Unlock
Domelight Supervision Wire Location: N/A
Horn Negative Wire (-): Brown/Red or Brown/Yellow
Horn Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): Black
Tachometer Wire Negative Wire Location: At Instrument Cluster
Brake Light Positive Wire ( ): Blue/Red or Green/Red
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): Disarms With Factory Remote Only. Factory Alarm Disarm Wire Location: N/A
Factory Anti-Theft System: Transponder Anti-Theft System, Requires Bypass And Extra Ignition Key. The 1997 model year vehicle may require a bypass module and an extra ignition key, if vehicle is equipped with a special key from BMW.
Factory Anti-Theft System Location: Transponder At Ignition Switch Tumbler
if you require further assistance please let me know and i will help assist you from there. Thanks, Midwest-Tek

Aug 27, 2010 | 1997 BMW 328

2 Answers

1989 Dodge Truck B250 Van V8-318 ignition control module location?


its built into the ecm located right in the middle of he firewall from under the hood, big black box with two plugs.

Jan 31, 2010 | 1988 Dodge B250

1 Answer

What color is the power wire in 1994 toyota pick up


this might help
1994 Toyota Pickup Car Security Wiring Diagram
Battery Constant 12v+ Positive Wire (+): White And White/Red
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness
Starter Positive Wire (+): Black
Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire (+): Black/Yellow
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire (+): Black/Yellow Or Black/Red
Second Ignition Positive Wire Location: Ignition Switch Harness
Accessory Positive Wire (+): Blue/Red
Accessory Positive Wire Location: Ignition Switch Harness
Parking Light Negative Wire (-): Red/Black
Parking Light Negative Wire Location: At Steering Column Harness
Parking Light Positive Wire (+): Green
Parking Light Positive Wire Location: In Drivers Kick Panel
Power Door Lock Negative Wire (-): Blue/White
Power Door Lock Negative Wire Location: At Door Control Relay. The door control relay, is located behind the driver dash speaker.
Power Door Unlock Negative Wire (-): Blue/Yellow
Power Door Unlock Negative Wire Location: At Door Control Relay. The door control relay, is located behind the driver dash speaker.
Door Trigger Negative Wire (-): Black/White Or Black
Door Trigger Negative Wire Location: At 2-Pin Plug, Top Of Fusebox
Domelight Supervision Wire: Use Door Trigger, Requires Relay
Domelight Supervision Wire Location: N/A
Horn Negative Wire (-): Green/Red
Horn Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): Black
Tachometer Wire Negative Wire Location: At Diagnostic Connector. The diagnostic connector, is located on the passenger inner fender near the fuse/relay box.
Brake Light Positive Wire (+): Green/White
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): N/A
Factory Alarm Disarm Wire Location: N/A
Factory Anti-Theft System: N/A
Factory Anti-Theft System Location: N/A

Nov 29, 2009 | 1994 Toyota Pickup

2 Answers

Where is the ignition control module located on a 1990 Subaru legacy 2.2l


Center of firewall. It is a black plastic box with 2 screws or e the ignition module could be mounted below the steering column.

Jul 04, 2009 | Subaru Legacy Cars & Trucks

1 Answer

Ignition Module


They don't have an ignition module per say.. You firing is controled by the PCM, which is the computer and is locater under your air intake box, which has to be remover for access. How did you come up with the idea it was a bad ignition module??

Aug 11, 2008 | 1997 Dodge Intrepid

Not finding what you are looking for?
1995 Oldsmobile Cutlass Ciera Logo

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...