Question about Nissan Altima

1 Answer

How to assemble a serpatine belt - Altima Nissan Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 266 Answers

THERE IS A WEB SITE ACCESSDAYCO.COM IT WILL SHOW YOU THE ROUTING

Posted on Oct 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I started my 2001 camero and smoke filled the inside through the vents this happened after a hard feeze, there was antifreez in the car, smoke also came out from under the hood. I turned the car off and my...


It sounds more likely to be the water pump that has failed.You should have it repaired as soon as possible or your timing belt may snap and cause further damage.
I hope I have been of help

Feb 14, 2011 | Chevrolet Camaro Cars & Trucks

1 Answer

How to replace serpatine belt


The diagram should be around the engine somewhere, shows the pattern of the belt. You need to put a socket in the crankcase. Pull the socket toward the front. This will move the pulley, so you can slip the belt on.

Feb 13, 2011 | 1997 Toyota Avalon

1 Answer

Trying to find the adjustment for the serpatine belt. how to loosen to gt belt back on


serpentine belts ussually have a spring loaded idler pulley, they are like that to maintane constant pressure on belt,no adjust nessary,find idler pulley,it's on a accentic, turn it against the spring to loosen, slide off belt

Jan 31, 2010 | Jeep Wrangler Cars & Trucks

1 Answer

Changing a serpatine belt on s40 volvo


Use a rachet to relieve the tension on the idler wheel, remove old belt, install new belt using the guide, either under the hood, or from the manual. Again use the idler tension relief to finish. when the rachet is on the idler wheel it is usually used to lift wheel off belt, to relieve tension.

Dec 28, 2009 | 2005 Volvo S40

1 Answer

1999 serpatine belt


Hi,the serpentine belt is tensioned automatically by means of a spring loaded tensioner,this is released by using a long 1/2 inch extension bar which fits into a square hole, once pulled back the tensioner can then be held by a nail etc, which is inserted into a hole which aligns with another hole,thus holding the tensioner back in a pre-loaded position to allow you to replace the belt,once replaced you can then pull back the extension bar to remove the nail again and then slowly let off the tension, IF replacing the tensioner, The new one comes pre-loaded with a pin in location to hold it ,hope this is of some help, Bill.

Feb 20, 2009 | 1999 Saab 9-5

1 Answer

Size of serpatine belt to reroute with out AC


hi the only way to get the size is to use a piece of string and wrap it around all of the pullies.in the proper order. and subtract 1-2 inches so thy tenshioner will work buy a couple of belts at diffrent sizes and return the ones you dont need

Feb 02, 2009 | 1996 Jeep Grand Cherokee

1 Answer

I need to do serpatine belt on 96 ford taruaus 3.0


On the Inside of the Engine Compartment you will find the Routing Sticker for the Belt to Reinstall. Locate the Tensioner (Will look like a Pulley that has one Round Pulley Under the Belt and One larger Round Pulley Mounted Above that. In the Middle of the Large Pulley there is a Bolt. Get a Wratchet and Turn it. It will Lower the Pulley under the Belt and Loosen the Tension Off of the Belt. Remove the Belt. Follow the Diagram Under Hood to Reinstall.

Dec 31, 2008 | 1996 Ford Taurus

1 Answer

Serpatine belt replacement


hope this is what youre looking for.1bb6526.gif

Nov 30, 2008 | 1991 Chevrolet S-10

1 Answer

Serpertine belt diagram


0900c152800a326f.gif
Copyright © 2002 Delmar, All Rights Reserved.

Oct 19, 2008 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...