Question about Chevrolet 2500

1 Answer

Hello i changed out my wheel hub assembly and my abs light is on now and i even changed it back with the old hub and still shows the light on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

Disconnect the negative battery lead for a minute or two and reconnect. You disconnected the sensor while the battery was still connected.

Posted on Oct 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced rear hub assembly and got er55 on odometer and abs light


reset computer this should remedy problem
if doesnt replace abs sensors the wheels should always be done in pairs or all around brakes never one at a time very unsafe

Nov 09, 2013 | 2005 Subaru Legacy

1 Answer

I have a 2000 olds alero. I'm having a problem with the ABS, and Traction Control System. I've scanned the ABS system,and it shows RF wheel speed sensor ckt open/ shorted. I checked all fuses


The EBCM is looking for 1040-1160 ohms in the ABS sensor circuit. Check the two wires between the sensor and the EBCM. The wires in the area under the fender are prone to breakage caused by the flexing and turning of the suspension.

Mar 31, 2012 | Cars & Trucks

2 Answers

Front passenger brake is pulsing and there is no abs light on in my 1997 pontiac grand prix.I believe it might be abs sensor but don't know where to find it in wheel assembly.


A front brake pulsing with no ABS light is a rotor that is no longer true i.e warped. Pull off the tire and rotate the rotor. Hold a straight edge (ruler) across the outside of the rotor as your rotating the rotor. You will note that it changes distance on the straight edge / ruler as it rotates. (in out wobble) A good way to test for an out of true rotor is to drive at about 45 miles and hour and really stand on the brakes (do not lock them up) If the steering wheel and or brake pedal pulsate... you most likely have a rotor problem. If your rotor has never been "turned" it is probably time to do so.

The ABS sensor is behind the rotor on the lower control arm pointed outward toward the rotor with a flat button face. You can not see the button face with the rotor installed. If the sensor is bad you will have an ABS light. I think your troubleshooting the wrong problem. i.e rotor vs your current focus of the ABS sensor.

I would like some feed back on the running dynamic on the road brake test.

Thanks for choosing FixYa,
Kelly

Jun 06, 2011 | 1997 Pontiac Grand Prix

3 Answers

My 2003 mercury mountaineer ABS light is staying on. manually, the brakes work however they shimmy.changed the brake pads,checked the brake fluid and ABS fuse,bud when changing the pads,did now clean the...


I replaced the hub bearing assembly on drivers side twice and the light stayed on and the brakes worked fine. It was the wires (visible just above the tire on the frame) that rubbed against the frame that had shorted out. It was simply repaired and clip-stripped up out of the way. The light has been off every since then.

Dec 30, 2010 | 2003 Mercury Mountaineer

2 Answers

My abs break light comes on when i have to hit my breaks hard. sometimes it comes on and go's out after i turn the car off.I was told that i needed a left wheel hub bearings. It's a 98 acura 3.2 TL I was...


Hi

This is most likely one of 2 things 1 the abs sensor on one wheel is faulty, not uncommon cost about $80 for a new one. or you can clean the old one as often they get dirty from brake dust.

secondly the brake pads may need replacing, the ABS warning light is to let you know that these may need replacing, often when it is the brakes they will fel different as you press it down, sometimes they push back up towards you as your pushing down. I would have the back brakes checked as that is normally the cause.

you can still drive the car no problem.
hope that helps
Regards
Dan

Dec 27, 2010 | Acura TL Cars & Trucks

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

How can I tell if a wheel bearing is going bad.


Wheel bearings in the front or back will howl when going bad, and might even click and clack when going over bumps.

One can jack up the car and move the wheel in the 9 and 3 o'clock positions and the 12 o'clock and 6 o'clock positions to see if there is excessive movement of 1/4" or more.

Also, if a hub wheel bearing is bad, and the ABS light goes on for it, then sometimes the whole hub assembly must be replaced on the wheel affected to get ABS Braking back.

Aug 19, 2010 | 2003 Chevrolet Malibu

3 Answers

Abs code c 0036,front left wheel speed circuit range / performanc


I agree that it is more then like the the hub bearing assembly that also houses the speed sensor I would first check that there is no damage to the wiring that goes to the hub bearing that could be easy repaired, or debri that has been caked in between the sensor & the hub, use an air preesure to clean it out. Hub bearings are very expensive, so try this first. Good luck

Jun 26, 2010 | 2004 Pontiac Grand Prix

1 Answer

1992 Honda Accord EX Replacing the Rear Wheel Assembly


It won't make any difference, seeing that the car is older and you don't have the ABS functionable it won't change anything. You already have the ABS light on so nothing new will happen.
Regards
Sam

May 05, 2009 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...