Question about 2001 Ford Taurus

1 Answer

Can i change my altenator pully? - 2001 Ford Taurus

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

Yes, but you might need an impact wrench

Posted on Oct 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, i am changing my 1.6lt 95model ford lasers alternator belt, wich runs from the harmonic balancer to the water pump pully to the alt' pully.... Please!.... how do i back the altenator off? Not much room...


I would have thought it is a stretch belt you wind the old 1 off ( that's easy) then wind the new 1 on ( with out the tool mind even with the tool tricky) remember to wind the crank clockwise or you could jump timing hope this helps

Jan 22, 2015 | Ford Cars & Trucks

1 Answer

Rattling noise,and think it is the pully on the altenator 2001


Remove fan belt start car and see if there is still a noise. If there is its not the alt.

Aug 02, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

Need to know how to put a serpentine belt on a 1995 302 ford motor


Below the altenator is a tensioning pully, insert a 3/8" ratchet or breaker bar in the square hole on the tensioner and release the tension on the surpentine belt and remove the belt. Route the new surpentine belt in place up to the altenator and take the tension off the tensioner and put the belt over the altenator pully. Double check to make sure the belt is riding correctly on all the pullies before starting. Crank the engine over several times before starting to seat the belt. f78f558.jpg

Jun 02, 2010 | 1995 Ford Mustang

1 Answer

Change alternator


It's easy...
Disconnect the battery
Remove the supentine belt from the altenator pully, you can use a 3/8" drive breaker bar on the belt tensioner, just insert into the square slot on the tensioner and rotate it clockwise.
Remove the power wire and the harness
Remove the mounting bolts 1 under and 2 on the sides.

Just reverse the process to install the new altenator.
Make sure the supentine belt is in the proper position.
Make sure the battery is charged before starting, a drained battery can damage the FETs on the new altenator.

May 22, 2010 | 2004 Ford Mustang

1 Answer

Install a altenator for a 2006 jeep commander


I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

May 20, 2010 | 2006 Jeep Commander

2 Answers

Replace altenator 2002 bmw 325ci


disconnect the negative battery. remove the belt by rotate the tensioner roller clockwise. from the left car side u will see three hexagon screw 13mm under the altenator. loose out the screw and remove the altenator. before that unplug the two wire behind the altenator.tq

Feb 28, 2010 | 2001 BMW 325

1 Answer

One bolt is in the way by a 8th of an inch.


You may be able to get it out with the altenator if you have the other bolts rmoved. You will have to place this bolt in hole when reinstalling the altenator.

Dec 31, 2009 | 1994 Mazda MPV

1 Answer

Replace serpentine belt in 1996 Grand AM


One belt to replace, get the correct belt and wrap around all pullys, smooth pullys get smooth side of belt and rigid pullys get rigid side of belt, loosen altenator for removal and remounting then moove back to position and tighten.

Jun 13, 2009 | 1996 Pontiac Grand Am

1 Answer

Altenator replacement


has a tention pully holding on the belt.. the pully will have a single bolt head ing the center.. its on a piviting arm thats spring loaded.. get a wrench or ratchet on the bolt in the middle of the pully and push or pull it till it releaves the stress on the belt..

Nov 11, 2008 | 1995 Buick Riviera

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...