Question about Chevrolet 1500
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
try this website to see if they have you car listed its www.edmund.com if they do you be able to download a owner manual also would like to give you this information if you every have a hard to find GM-part they only sells GM-parts uts Schram auto & truck parts 1-800-292-1032 and they website is www.schramauto.com i hope i was able to give you some help Michigan Man.
Posted on May 22, 2009
FIRST OF ALL YOU NEED STEERING WHEEL PULLER.AND LOCK PLATE TOOL J - 23653. GETTING STARTED.DISCONNECT THE NEGATIVE BATTERY CABLE.REMOVE THE LOWER TRIM PANEL.REMOVE THE STEERING COLUMN RETAINING BOLTS.LOWER THE STEERING COLUMN ASSEMBLY TO GAIN ACCESS TO THE SWITCH RETAINING SCREWS.BECAREFUL DONT DAMAGE THE COLLAPSIBLE COLUMN.MAKE SURE THE SWITCH IS IN THE LOCK POSITION.IF THE LOCK CYLINDER IS OUT PULL THE SWITCH ROD UP TO THE STOP THEN GO DOWN 1 DETENT.REMOVE THE ELECTRICAL CONNECTIONS FROM THE SWITCH.REMOVE THE SWITCH RETAINING SCREWS.REMOVE THE SWITCH FROM THE COLUMN.INSTALLATION IS THE REVERSE OF THE REMOVAL PROCEDURE.BEFORE INSTALLATION MAKE SURE THE SWITCH IS IN THE LOCK POSITION.WARNING USE ORIGINAL SCREWS.IF YOU USE TOO LONG SCREWS IT WILL PREVENT THE COLUMN FROM COLLAPSING ON IMPACT. NOW IF YOU ARE REMOVING THE IGNITION LOCK CYLINDER.DISCONNECT THE NEGATIVE BATTERY CABLE.REMOVE STEERING WHEEL.USING A STEERING WHEEL PULLER AND LOCK PLATE TOOL. J-23653 REMOVE THE TURN SIGNAL SWITCH. IT IS NOT NECESSARY TO COMPLETELY REMOVE THE SWITCH FROM THE COLUMN. PULL THE SWITCH REARWARD FAR ENOUGH TO SLIP IT OVER THE END OF THE SHAFT BUT DO NOT PULL THE HARNESS OUT OF THE COLUMN.TURN THE LOCK TO RUN.REMOVE THE LOCK RETAINING SCREWS.AND REMOVE THE LOCK CYLINDER.NOTE IF THE RETAINING SCREW IS DROPPED ON REMOVAL.IT MAY FALL INTO COLUMN REQUIRING COMPLETE DISASSEMBLY OF THE COLUMN TO RETRIEVE THE SCREW.TO INSTALL. ROTATE THE KEY TO THE STOP WHILE HOLDING ONTO THE CYLINDER.PUSH THE LOCK ALL THE WAY IN.INSTALL THE SCREW TIGHTEN THE SCREW TO 40 INCH LBS FOR REGULAR COLUMNS 22 INCH LBS FOR ADJUSTABLE COLUMNS.INSTALL THE TURN SIGNAL SWITCH AND STEERING WHEEL.WARNING THIS JOB IS A SKILL LEVEL B MEANING YOU MUST HAVE BASIC KNOWLEDGE OF COMPLEX SYSTEM.DONT DO THIS JOB IF THIS IS YOUR FIRST TIME WORKING ON A VECHICLE.
Posted on Nov 11, 2009
pick up a chilton book from chapters indago and check the diagrams they might be similar but i believe the wiring is a lot different '
it is likely you will need both manules
Posted on Jan 08, 2010
Tips for a great answer:
Nov 13, 2017 | Cars & Trucks
Jul 29, 2016 | Chevrolet Cars & Trucks
May 25, 2014 | 1984 Chevrolet C2500
Jan 08, 2010 | Chevrolet Chevy Cars & Trucks
Dec 23, 2009 | 1981 Ford F 100
Nov 27, 2009 | 1981 Chevrolet Corvette
Dec 31, 2008 | 1994 Dodge B Series Cargo
132 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: