Question about 1997 Mercury Villager

1 Answer

Step by step guide on how to replace a front blower motor on a 1997 Mercury Villager

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Posted on Oct 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The front blower switch works only in 4 position


it the resister in the plenum case. Your blower motor is going and drawing too much current. If repat failure, replace the blower motor. not hard.

http://groups.yahoo.com/group/villagerquest/

Aug 30, 2010 | 2001 Mercury Villager

1 Answer

A/C fan switch only works on high


it's your blower motor resistor in the plenum case. They usually blow the thermal limiter because the blower motor is drawing too much current. It's starting to go.
You can replace the resistor, 2 screws under the dash on the passenger side. It has a 4 or 5 wie connector. About $25 from a Ford or Mercury dealer.
Also go to the Villager site for more help.

http://groups.yahoo.com/group/villagerquest/

Jun 15, 2010 | 2001 Mercury Villager

1 Answer

1999 mercury villager put in new blower motor and resistor. Every so often when change modes from defrost to lower for example or on start up it blows the front blower motor fuse. the blower motor is a...


it could be the electronic blend door motor. Try not changing any settings for a week and see if the fuse blows. Leave it on floor/defrost.

usually it is the bearing in the blower motor going bad. I believe it's a 25 amp fuse. The motor draws about one amp for each volt increase up to 14 volts.

go to our site for more help.

http://groups.yahoo.com/group/villagerquest/

Feb 02, 2010 | 1999 Mercury Villager

3 Answers

How many oxygen censor in 1997 mercury villager van I have to change new one some one told me more than two censor problem is check engine light is on


I have a 1997 Mercury Villager with many miles. We get poor gas mileage. The check engine light is on. I want to replace the 02 sensor but cannot locate it on the engine. Is there a link with photo of physical location of the sensor and what are the steps to replace it?

Oct 19, 2009 | 1997 Mercury Villager

2 Answers

My rear ac on my mercury villager is not woring the ligth on it are on just it is not blowing , i replace the blower and resistor and all fuses are ok still not working , help please


yes hi you guys was right about the resistor needed to be clean with some alcohol and it work out reaaly good and the blower stort blowing , full ac/ haet all are working thanks fixya

Jun 05, 2009 | 1997 Mercury Villager

1 Answer

How can i replace it?


http://autos.groups.yahoo.com/group/villagerquest/

it's usually called the trans mount cause that's what's on that side.

Section 02-03: Engine and Transaxle Mounting 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Support Insulator, Front Transaxle Removal
  1. Remove the battery (10655). Refer to Section 14-01 for the removal procedure.
  2. Remove the Engine Air Cleaner (ACL) (9600). Refer to Section 03-12 for the removal procedure.
  3. Remove the radiator coolant recovery reservoir (8A080). Refer to Section 03-03 for the removal procedure.
  4. Remove the battery tray (10732). Refer to Section 14-01 for the removal procedure.
  5. Support the transaxle with a floor jack.
  6. Remove the front transaxle support insulator through bolt and nut.
  7. Remove the three front transaxle support insulator bolts and the front transaxle support insulator.
-----------------------------------------------------------
Support Insulator, Rear Transaxle Removal
  1. Remove the rear transaxle support bracket. Refer to the procedure in this section.
  1. Raise and support the vehicle.
  1. Remove the three rear transaxle support insulator nuts.




  1. Lower the vehicle.
  1. Remove the rear transaxle support insulator from the vehicle.

Mar 29, 2009 | 1997 Mercury Villager

Not finding what you are looking for?
1997 Mercury Villager Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...