Question about 1992 Chevrolet S-10

1 Answer

Fiber timing gear was slipping on alunm. bought new gears,how do you set timing marks since gears are offset,mark to mark or straight up and down

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 540 Answers

Mark to mark..

Posted on Oct 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i set timing chian marks


The marks are on the crank and cam gears. They either have a mark on the head that coincides with the mark on the cam gear AND you set that AND then bring the crank shaft gear to TDC on the timing marks OR you have both marks on the gears and you line them up with each other using a straight edge through the center of the shafts, then you put the chain on.

Jun 03, 2014 | 1997 Nissan Maxima

1 Answer

How to remove the timeing chian


22R 4 cyl.Get # 1 piston to TDC(stick the harmonic balancer back on temporary)setting the mark to O on the timing tab,pull the balancer back off and slip the chain on the crank gear after finding the single dot on the chain.Set the mark on the cam gear at very top and put the chain mark on that mark on the cam gear.Stick the cam gear back on the cam and bolt it back on.Your set now.

Apr 11, 2014 | Toyota Hilux Cars & Trucks

1 Answer

Looking for timing marks for a 3.1


set the ff:
cranckshaft set the gear straight up = 12 o'clock (#1 piston must be at TDC)
camshaft set the gear straight down = 6 o'clock
to verify, the rotor of the distributor is pointing at #1 plug wire.

Feb 24, 2012 | 1993 Oldsmobile Cutlass Supreme

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

1 Answer

I changed out the old timing gear for a new one. How do I set the timing gear?


have the cam gear and the crank gear dimples facing one another. The crank gear has the dimple facing straight up and the cam gear dimple straight down. The dimples are marked in the flat side facing outward in one tooth in each gear

Apr 09, 2010 | 1985 Chevrolet Chevy

1 Answer

How do you replace timing chain in a1988 chevy s10 with a 2.8 where are marks on gears set do you use #1 top dead center or #4 tdc


Line up the crank gear timing straight up, line up the cam gear timig mark straight down (so the marks are closest to each other, or facing each other). the distributor will be firing #4.

Mar 05, 2010 | 1988 Chevrolet S-10

1 Answer

I need to correctly put a F250 with a 86 351 winsdor motor back in time? - time chain and gears


Not terribly complicated. Set the crankshaft at TDC on timing scale before you start, as a reference. If the cover is off just stick it back on there for a minute and same for harmonic balancer.
Once you have done that you should see a mark on the lower gear, either straight up at the top or straight down (if at bottom, put damper back on and turn till it points up.) You should be able to find a corresponding mark on the cam gear. That mark needs to point down, directly at the one on the crank gear. To do that, loosely install the cam gear on the cam and turn it till it lines up. Remove the cam gear and place the chain over it and the bottom gear. do not change the crank or cam position. To check for proper alignment, put the balancer on the crank ant turn it exactly two turns. the marks should return to original indexing. Make sure you have everything tightened up and then put the remainder of the engine back together.

Dec 08, 2009 | 1986 Ford F 250

1 Answer

Want to know positioning of the timing mark on the timing gears5.8L


The Timing Marks should face each other crank gear mark straight up and cam gear mark should point down straight at crank gear mark

Oct 25, 2009 | Ford E-250 Cars & Trucks

1 Answer

How to align timing marks on gears of 1992 chevy truck with a 350 5.7 engine


Mark on cam gear points straight down, one on crank gear points straight up directly at the one on cam gear.

Oct 03, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Timing marks and procedures


If it is the 2.5 EJ25 motor the marks ar on the cover and pulleys. Top pulleys are Single line straight up and double straight down which should line up with bottom pulleys double marks. This should line up the single lines on bottom pulleys with 90 degree mark on outer cover both sides.The center pulley for crank should be straight up with notch in block.

Jul 23, 2008 | 1998 Subaru Legacy

Not finding what you are looking for?
1992 Chevrolet S-10 Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...