Question about 1996 Mitsubishi Mirage

Open Question

I want to adjust valves on a 4G15 mitsu engine 1996 mirage 1.5. I have specs, feeler guages general purpose tools. Before I pull of the valve cover, was wondering if any special toos are required.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MrScary66613
  • 1990 Answers

SOURCE: What would cause the fuel trim check engine code?

It sounds like it is telling you that the Fuel Cap needs to be Replaced. if the Seal on the Cap is Bad, It will **** air into the Fuel tank.

Posted on Jan 23, 2009

Ad
c17hydro
  • 2984 Answers

SOURCE: need engine specs for mitsubishi pajero 1996 3.5 lt 24 valve dohc

ed904ac.gif
Here ya go....get the rest of the info right now.

Posted on Mar 26, 2009

  • 64 Answers

SOURCE: Mitsubishi Eclipse Harmonic Balancer 3.0L Removal

There is a panel inside the wheel well that you can take off that gives you perfect access to the harmonic balancer. A special tool is required. i had my dad make one because he has access to whatever he needs at the factory. but you can get them at the dealer. i have no clue how much they cost. I can't see any way of doing it without the special tool. after you get the tool its pretty simple to get off. it takes alot of force to break the bolt loose though. i used the handle off my jack as a cheater bar. hope this helps...

Posted on Jun 29, 2009

  • 510 Answers

SOURCE: need valve adjustment for 1998 lancer 4g15 engine

I take it you mean 4g13 engine
if so inlet mm 0,20 HOT
ex mm 0,25 HOT.

Posted on Nov 08, 2009

  • 181 Answers

SOURCE: My 1994 Mitsubishi Lancer (4g15) engine stops

Fuel pump

Posted on Mar 06, 2010

Testimonial: "It's the fuel pump indeed. Also the gas tank found to be very dirty. The fuel pump was replaced, fuel system cleaned, now the car runs perfectly."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I set tappets on Nissan 1400


With a special tool called a feeler gauge remove the valve covers and one by one bring the cylinders up to top dead center (both valves are fully closed at this point) adjust to factory spec. All adjustments are done cold. If engine is very high miles reduce the clearances in specs by slight amount (.002") to the tight side to account for wear in the valve train parts.

Nov 16, 2015 | 2006 Nissan 1400 Bakkie

1 Answer

Need valve lash specs for 1980 suzuki dr400


Suzuki DR400S - Motorcycle Specs

www.motorcyclespecs.co.za/model/suzu/suzuki_dr400s%2080.ht
1980. Engine. Air cooled, four stroke, single cylinder, SOHC, 2 valves per cylinder ....Valve adjustment can be done without a feeler gauge and the CDI has ..

Dr400 valve adjustment 1 - YouTube

? 2:08
www.youtube.com/watch?v=BH-KFrpwo3w
Nov 19, 2010 - Uploaded by obtrailriders
Dr400 valve adjustment 1. ... Suzuki DRZ 400 Valves clearance check \ sprawdzanie luzu zaworowego PART 2 ...

Nov 01, 2015 | Suzuki Cars & Trucks

1 Answer

How to adjust valves on Toyota 1991 23re engine


Very carefully my friend. Kidding. Ok, remove the valve cover and anything in your way of removing it. By hand, with a socket and ratchet, on the crankshaft bolt head, turn the engine over to get #1 piston to top dead center on compression stroke. You'll need to find out what the valve lash should be in order to adjust properly, I run the 22R engines and only have specs for that, and have a feeler gage to place between the valve head and rocker arm. Check the gap on the intake valve for it is in position to adjust now because the cam lobe is at the farthest away from the valve. If it needs adjusted closer, turn the nut loose and screw the center in to tighten and out to give more gap, then tighten the jam nut after adjusted. Now turn the crank to bring #3 to top dead center and adjust that intake. Once done go back to #1 exhaust and adjust it. You'll know when the #3 is TDC when the rocker is loose on intake valve along with #1 exhaust. Now bring #4 piston up to TDC and adjust intake valve. Like I said, you'll know when it's @TDC when that rocker is loose, but with the spark plugs out you can stick a screwdriver in the plug hole to be sure it's up. Firing order on 4 cylinders is 1-3-4-2 so do your adjustment in that order for each intake valve and go back to the last one adjusted and do the exhaust valve.

Dec 01, 2014 | Toyota Cars & Trucks

1 Answer

There is a tapping noise in the motor but its not knocking I think its a lifter it hasent lost any power and its really not getting worse I would like to know what the spec is for tighing down the lifter...


Depends on which engine you have. If you have


ADJUSTMENT Although it is sometimes possible to reuse an old cylinder head cover gasket, in most cases it makes more sense to purchase a new one before beginning the procedure. Some vehicles may require the use of silicone sealant either with or without a new cover gasket. For more details, please refer to the cylinder head cover procedures in Engine & Engine Overhaul of this repair guide and refer to the gasket manufacturer's instructions.

Z24i Engine
See Figures 1, 2 and 3
For the intake valves: 1-4-5-8 valve clearance is 0.012 in. (0.30mm). For the exhaust valves: 2-3-6-7 valve clearance is 0.012 in. (0.30mm). The pivot locknut torque specification is 12-16 ft. lbs. (16-22 Nm).

  1. The valves must be adjusted with the engine warm, so start the truck and run the engine until the needle on the temperature gauge reaches the middle setting. After the engine is warm, shut it off.
  2. Note the location of any wires and hoses which may interfere with cylinder head cover removal, disconnect them and move them to one side. Remove the bolts holding the cylinder head cover in place and remove the cover. Remember, the engine will be hot, so be careful!

fb38656.gif


Fig. Fig. 1: Check the valve clearance with a flat feeler gauge-Z24i engine





e459ab8.gif

Fig. Fig. 2: Loosen the locknut and turn the adjusting screw to adjust the valve clearance-Z24i engine


1c1d35c.gif


Fig. Fig. 3: With the No. 1 piston at TDC, adjust the top set of valves FIRST; with the No. 4 piston at TDC, adjust the bottom set of valves SECOND-Z24i engine

  1. Rotate the crankshaft until the timing marks indicate that the No. 1 piston is at TDC of the compression stroke. If you're not sure of which stroke you're on, remove the No. 1 spark plug and hold your thumb over the hole. Pressure will be felt as the piston starts up on the compression stroke.
  2. Refer to the accompanying illustration (upper part), then check valves (1), (2), (4) and (6) using a flat bladed feeler gauge. The feeler gauge should pass between the valve stem end and the rocker arm screw with a very slight drag. Insert the feeler gauge straight, not at an angle.
  3. If the clearance is not within the specified value, loosen the rocker arm lock nut and turn the rocker arm screw to obtain the proper clearance. After correct clearance is obtained, tighten the locknut.
  4. Rotate the crankshaft until the timing marks indicate that the No. 4 piston is at TDC of the compression stroke. If you're not sure of which stroke you're on, remove the No. 4 spark plug and hold your thumb over the hole. Pressure will be felt as the piston starts up on the compression stroke.
  5. See the illustration (lower part), then check valves (3), (5), (7) and (8). Check and adjust valve clearance as necessary.
  6. Install the cylinder head cover gasket, the cover itself and any wires or hoses which were removed. Check the engine oil level.

KA24E, VG30i and VG30E Engines
See Figures 4 and 5
These models utilize hydraulic valve lifters. Periodic adjustment is neither necessary or possible. There is however a bleed down procedure that is necessary when the valve train has been disassembled.
HYDRAULIC LIFTER BLEED DOWN
  1. Remove the cylinder head cover.
  2. Check the lifters for proper operation by pushing hard on each lifter with fingertip pressure.
  3. If the valve lifter moves more than 0.04 in. (1mm), air may be inside it. Make sure the rocker arm is not on the cam lobe when making this check.
  4. Install the cylinder head cover.
  5. If there was air in the lifters, bleed the air by running the engine at 1000 rpm for 10 minutes.


4df22a2.gif


Fig. Fig. 4: Cross-sectional view of an installed hydraulic valve lifter-4 cylinder engine


6e01bb3.gif


Fig. Fig. 5: Cross-sectional view of an installed hydraulic valve lifter-6 cylinder engine

Oct 29, 2010 | 1989 Nissan Hardbody King

2 Answers

Procedure of tappet adjustment


make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl #4.now tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

Mar 14, 2010 | 1986 Suzuki Samurai

2 Answers

Rebuilt engine valves not adjusted.1970,s model 350 chevy i need to know the proper way to adjust before start up


you need feeler guage, youl need find the valve clearence to set it and adjust each one by using the rule of 9

Sep 21, 2009 | 1983 Chevrolet Chevy

1 Answer

How to adjust the valve adjustments


you need to remove the valve cover and if they are even adjustable there will be locknuts on a stud on one side you need feeler gauges and adjust by loosenin the nut with cylinder in compression sequence tightrn stud with screw driver or allen wrench whichever applies put feeler guage probably.018 between rocker and vale tightrn untilfeeler gauges move with some resistance lock nut tight but be sure you can still move feeler gauge get all cylnders then reinstall valve cover

Jul 21, 2009 | 1992 Daihatsu Rocky

3 Answers

Valve ajustment


easyiest way to do that is to go to your local library and look up you torque specs and sequence for your car.

Aug 03, 2008 | 1990 Honda Civic

2 Answers

New rebuild chatters


adjust your valves your oil pickup tube needs to be adjusted you need feeler guages to adjust the valves down properly
make sure lifters and oil pick up tubes are not clogged

feeler guage is---> thin pieces of metal cut to different sizes to hold under valve adjusters till the play and chatter gone
check by book what the feeler size needed for adjustment

Jun 07, 2008 | 1983 Chevrolet C3500

Not finding what you are looking for?
1996 Mitsubishi Mirage Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...