Question about 1990 Nissan Hardbody King Cab

Open Question

What size bolts are on a starter 91 nissan pickup 2x4 2.4 liter

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I have a 1995 nissan

The starter has to be removed from the top through the right side of the engine. Removing the bracket holding the gas filter allows enough room for the starter and solenoid to pass through the opening. I had to use a 14 mm wrench instead of a socket to remove the bolts as there is no room for the socket wrench even with extensions.

Posted on Jul 31, 2008

  • 140 Answers

SOURCE: Chevy S10 Pickup Starter. Removed the two bolts

you also have two or three wires holding the starter inplace.. remove the wires and your problem should be solved.. p.s. it is a tight spot so you will need to wig. it alot... good luck keith..

Posted on Mar 14, 2009

  • 10 Answers

SOURCE: Can't get the starter out of a 1991 Nissan pickup.

The second bolt is hidden way up and tucked in near the solenoid. You need to setup a ratchet with extensions/socket (14mm) combination that is just a little longer than the starter motor. If you just can't picture where the bolt is, then go down to the parts store and look at/purchase the replacement starter to see how it mounts up.
There are two bolts for the starter mount and one nut for the main starter power lead. There is one plug for the starter key switch.
Disconnect plug. Loosen lower bolt. Remover upper bolt. Remove lower bolt. Twist starter so you can remove main power cable nut (be sure to have disconnected the battery first!) Pull starter.

Posted on May 10, 2009

  • 434 Answers

SOURCE: I Have a Nissan/Datsun 720 Pickup (Gas). Trying to

You can use any carb as long as it bolts up and seals, and the cfm is the same

Posted on Jun 26, 2009

  • 2 Answers

SOURCE: 1993 Nissan pickup, replacing starter

I have a '95. It's behind the passenger side tire. Remove tire and rock guard if you have one--couple of screws--and you can easily access it. two bolts facing rear of car, two connections up front. Honestly it was the easiest replacement I've ever done. Just disconnect your battery first.

Posted on Jul 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 nissan pickup Fan Replacement


The bolts will be either 6mmx1.25 or8mmx1.25. The 1.25 is the thread pitch . They are about 12-15mm long. The spanner size is 10mm. I hope you mean the viscous hub to water pump flange or is it the fan from the viscous hub

Mar 03, 2013 | 1994 Toyota Pickup

1 Answer

91 nissan will not engage starter when ignition is turned


It could be that relay, or a dead spot on the starter.
Can you jumper the starter and make it crank ?

Jan 17, 2013 | 1991 Nissan Pickup

1 Answer

How to change a starter for a 4x4 sr 5 91 toyota v6


you must remove oil filter and exhaust heat shield.

May 10, 2010 | 1991 Nissan Pickup

1 Answer

1992 Pickup: how to change a starter on 92 toyota pickup...


disconnect the battery take the power wires off the starter turn the bolts counterclockwise pull up slightly on the starter and pull out reverse process to reinstall.

May 07, 2010 | 1992 Nissan Pickup

1 Answer

How do I remove/install a starter on 1996 nissan


this is pretty cut and dry, remove neg battery terminal, raise vehicle if needed, remove the wiring from the back of starter, then remove the two starter mounting bolts and pull starter out, to install reverse directions, good luck.

Mar 06, 2010 | 1996 Nissan Pickup

1 Answer

How to replace a starter on a 95 nissan hardbody 3.0 liter


disconnect the battery and then the starter wires on the starter underside of the engine then undo the two boltsx and slide the starter out. you might got to library and get a Haney's manual

Dec 06, 2009 | 1995 Nissan Pickup

1 Answer

Can't get the starter out of a 1991 Nissan pickup.


The second bolt is hidden way up and tucked in near the solenoid. You need to setup a ratchet with extensions/socket (14mm) combination that is just a little longer than the starter motor. If you just can't picture where the bolt is, then go down to the parts store and look at/purchase the replacement starter to see how it mounts up.
There are two bolts for the starter mount and one nut for the main starter power lead. There is one plug for the starter key switch.
Disconnect plug. Loosen lower bolt. Remover upper bolt. Remove lower bolt. Twist starter so you can remove main power cable nut (be sure to have disconnected the battery first!) Pull starter.

Apr 18, 2009 | 1991 Nissan Pickup

Not finding what you are looking for?
1990 Nissan Hardbody King Cab Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...