Question about 2003 Jaguar S-Type

1 Answer

2003 jaguar s-type how to bleed the brake when there air in them

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jaguar Master
  • 17,970 Answers

For Jaguar 2000-06 - Bleeding the Brake System (Repair Guide)

WARNING Brake Fluid contains polyglycol ethers and polyglycols. Avoid contact with the eyes. Wash hands thoroughly after handling. If brake fluid contacts the eyes, flush the eyes for 15 minutes with cold running water. Get medical attention if irritation persists. If taken internally, drink water and induce vomiting. Get medical attention immediately. Failure to follow these instructions can result in personal injury.
CAUTION Make sure that the vehicle is standing on a level surface or supported on a wheel free lift.
CAUTION If brake fluid is spilt on the paintwork, the affected areas must be immediately washed down with cold water.
CAUTION Make sure that the filler cap does not become contaminated.
NOTE The system consists of separate circuits for each front and diagonally opposite rear wheel. Each front to rear circuit and each wheel circuit can be bled individually of each other.
NOTE The service ABS hydraulic control unit is supplied pre-filled with brake fluid. Therefore, a conventional bleed procedure should be adequate to remove all the air from the brake system.

  1. Remove the master cylinder reservoir filler cap.
  2. Fill up the master cylinder reservoir to the MAX mark as necessary.
  3. Install a bleed tube to the rear right-hand brake caliper bleed nipple.
  4. Bleed the circuit by performing the following:
    Make sure the bleed tube is firmly attached to the bleed nipple. Submerge the end of the bleed tube in a bleed jar containing a small quantity of approved brake fluid. Position the bleed jar base at least 300 mm above the bleed nipple to maintain fluid pressure and prevent air leaking past the bleed nipple threads. Open the bleed nipple half a turn. Slowly apply the brake pedal to its maximum travel (this forces brake fluid into the bleed jar). Close the bleed nipple. Return the brake pedal to the rest position. Wait 2 seconds to allow the brake fluid to replenish the system. Fill up the master cylinder reservoir to the MAX mark as necessary. Continue to bleed the circuit until air-free brake fluid is pumped into the jar. Fully tighten the bleed nipple.
  5. Repeat the procedure for the rear left, front right and front left-hand brake circuits.
  6. Fill up the master cylinder reservoir to the MAX mark.
  7. Install the master cylinder reservoir cap.
I hope helps.

Posted on Oct 13, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: How can you bleed the left rear brakes on a 2003 Jaguar X-type?

keep pumping the brakes .it will bled .

Posted on Feb 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't retract brake piston, right rear wheel


u need a special tool becuase the e brake is in it and it turns clock wise or it is a ceased piston replace caliper would have to it but one of them .good luck or make sure if u open the brake line u bleed the system accordingly to manurfactsure.

Feb 18, 2011 | 2003 Jaguar X-Type

2 Answers

Thanks for the help ! but how do you bleed the lines?


Bleeding brakes in not difficult; however, it must be done correctly. The attached link is very discreptive and will walk you through everything needed (pictures are included).

http://www.popularmechanics.com/cars/how-to/maintenance/4213448

Please remember to rate my solution. Thanks!

Jan 24, 2011 | 2003 Jaguar X-Type

1 Answer

Brake problem


If you have broken the brake lines loose from the brake system anywere, thenit will have to bleed the air out of the brake lines. Check the fluid level in the master cylinder and keep it full while bleeding the brakes. Also you could have a leaking caliper on the car. Hope this will help you.

May 12, 2010 | Cars & Trucks

1 Answer

Brake problem


hi this is air in the system if you pump them do they go hard as normal? what you will need to do is , starting from the furthest caliper away from the fluid bottle you have to bleed the air out, you can buy bleeding systems for a few bucks/pounds but you can also do it yourself, to do this, find a length of small bore clear hose/pipe, locate the bleed nipple on the caliper, find a wrench/spanner that will fit the bleed nipple, put that on first, then get your pipe/hose, and slide that over the end of the bleed nipple ( make sure the pipe/hose is a nice tight fit ) locate a small clear glass jar partly fill it with brake fluid, put the hose/pipe into the jar so the fluid covers the end ( we don't want air to go up the pipe/hose ) then get a friend to pump hard on the brake pedal till it goes hard, and when it does tell them to keep their foot hard on the pedal , you then undo the bleed nipple ( you should get some fluid come out fast) when the pedal reaches the floor ( this happens immediately if you have opened the nipple far enough, then when it has hit the floor do the bleed nipple up again before they raise the pedal keep doing this till you see no bubbles coming through the hose/pipe, repeat the operation on the next furthest away, and so on till all the air has been removed from the system, be sure to check the fluid in the reservoir regularly as this will cause air to get back into the system again if it runs to low....hope this has helped and good luck, please vote thanks

Mar 20, 2010 | 2002 Jaguar X-Type

1 Answer

Just changed brakes but the pedal will not biuld pressure


antilock brake actuator has air trapped in it.

Mar 24, 2009 | 2002 Jaguar X-Type

1 Answer

How do you bleed the left rear brake 03 Jaguar.


i would try vacum bleeding it....you can use a tool like a "mity-vac"

Feb 24, 2009 | 2003 Jaguar X-Type

Not finding what you are looking for?
2003 Jaguar S-Type Logo

Related Topics:

1,087 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...